Abstract:This article reports on the design and characterization of a high-overtone bulk acoustic wave resonator (HBAR)-oscillator-based 4.596~GHz frequency source. A 2.298~GHz signal, generated by an oscillator constructed around a thermally-controlled two-port AlN-sapphire HBAR resonator with a Q-factor of 24000 at 68$^{\circ}$C, is frequency multiplied by 2 to 4.596~GHz, half of the Cs atom clock frequency. The temperature coefficient of frequency (TCF) of the HBAR is measured to be $-23$~ppm/$^{\circ}$C at 2.298~GHz. The measured phase noise of the 4.596~GHz source is $-105$~dBrad$^2$/Hz at 1~kHz offset and $-150$~dBrad$^2$/Hz at 100~kHz offset. The 4.596~GHz output signal is used as a local oscillator (LO) in a laboratory-prototype Cs microcell-based coherent population trapping (CPT) atomic clock. The signal is stabilized onto the atomic transition frequency by tuning finely a voltage-controlled phase shifter (VCPS) implemented in the 2.298~GHz HBAR-oscillator loop, preventing the need for a high-power-consuming direct digital synthesis (DDS). The short-term fractional frequency stability of the free-running oscillator is 1.8 $\times$ 10$^{-9}$ at one second integration time. In locked regime, the latter is improved in a preliminary proof-of-concept experiment at the level of 6.6 $\times$ 10$^{-11}~\tau^{-1/2}$ up to a few seconds and found to be limited by the signal-to-noise ratio of the detected CPT resonance.
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to develop a high - performance 4.596 GHz local oscillator (LO) suitable for micro - atomic clock (MAC) applications. Specifically, the research team designed and characterized an oscillator based on a high - order - harmonic bulk acoustic wave resonator (HBAR), which can generate a 2.298 GHz signal and then double the frequency to 4.596 GHz, which is half of the cesium atomic clock frequency. The paper explores in detail how to meet the requirements of this local oscillator in terms of volume, power consumption, output power range, frequency tuning resolution, phase noise, etc., in order to achieve a high - stability and low - power - consumption micro - cesium atomic clock.
### Main Problems and Challenges
1. **Volume and Power Consumption Requirements**:
- The oscillator needs to be integrated on an area of less than 1 square centimeter, and the maximum power consumption should not exceed 50 mW, so as to be suitable for battery - powered applications.
2. **Output Power Range**:
- The output microwave power needs to be adjustable between - 6 dBm and several dBm to drive a vertical - cavity - surface - emitting laser (VCSEL).
3. **Frequency Tuning Resolution**:
- The output frequency must have high resolution to ensure that the relative frequency error is much smaller than the target clock stability. Usually, a frequency resolution at the mHz level is required to ensure that the frequency stability is lower than 10^−12.
4. **Phase Noise**:
- The short - term frequency stability will be affected by the LO phase noise. The paper mentions that in order to achieve a short - term frequency stability of 2 × 10^−11 within 1 - second integration time, the phase - noise power - spectral density (PSD) of the LO at 2 kHz Fourier frequency must be lower than - 77 dBrad^2/Hz.
### Solutions
1. **Design of HBAR Oscillator**:
- Use a two - port AlN - sapphire HBAR resonator, whose Q - factor reaches 24,000 at 68°C. Through temperature control and a voltage - controlled phase shifter (VCPS) for coarse and fine tuning, the output frequency is accurately locked at 4.596 GHz.
2. **Frequency Doubling**:
- Double the 2.298 GHz signal to 4.596 GHz to drive the VCSEL laser.
3. **Phase Noise Optimization**:
- By optimizing the oscillator design and using a high - quality HBAR resonator, lower phase noise is achieved. The paper mentions that the phase noise of the 4.596 GHz signal at 1 kHz offset is - 105 dBrad^2/Hz, and at 100 kHz offset is - 150 dBrad^2/Hz.
4. **Experimental Verification**:
- Use the 4.596 GHz signal in a coherent population trapping (CPT) cesium atomic clock experiment. By adjusting the bias voltage of the VCPS, the LO frequency is locked at the atomic transition frequency, thus improving the short - term frequency stability of the clock.
### Conclusion
This paper successfully designed and implemented a 4.596 GHz local oscillator based on HBAR, which meets the strict requirements of micro - cesium atomic clocks for volume, power consumption, frequency stability, and phase noise. The experimental results show that the short - term frequency stability of this oscillator in the free - running mode is 1.8 × 10^−9, and in the locked mode it can reach 6.6 × 10^−11 τ^−1/2, demonstrating its potential in high - performance micro - atomic clock applications.