CESR positron source

A. Mikhailichenko

DOI: https://doi.org/10.48550/arXiv.1505.01406

2015-05-06

Abstract:Some details of the new positron converter and power supply are described. This converter unitso far doubled the amount of positrons accelerated in CESR.

Accelerator Physics

What problem does this paper attempt to address?

High Power Polarized Positron Source

Alexander Mikhailichenko

DOI: https://doi.org/10.48550/arXiv.1610.04666

2016-10-15

Abstract:We discuss the basis of polarized positron production by low energy polarized electrons. Efficiency of conversion ~0.1-1% might be interesting for CEBAF facility and ILC as well.

Accelerator Physics
Development of a Solid-State, High-Current, Repetitive Pulse Power System for Positron Source Prototype

Jingdong Liu,Xiaoping Li,Yunlong Chi,Jingyi Li,Dayong He,Xiang He,Guoxi Pei,Lei Shang

DOI: https://doi.org/10.1109/tps.2021.3132149

IF: 1.368

2022-01-01

IEEE Transactions on Plasma Science

Abstract:The positron source is one of the most important parts of the circular electron–positron collider (CEPC) linear accelerator. The design goal is to obtain a 3 nC bunch charge positron beam from a 4 GeV primary electron beam with an intensity of 10 nC/bunch. In this study, an all-solid-state, high-current pulse power system was developed to drive a flux concentrator to capture positrons by generating a magnetic field with a peak value of 6 T. Based on the inductive load topology circuit, the optimized parameters were designed to generate a pulse current with a high peak value and a high rise rate pulse current. In addition, a non-reverse voltage was realized to protect the solid-state switch components. For the characteristics of the long-distance transmission between the pulse power supply and the load in the system, the influences of the cable distribution parameters on the pulse were analyzed, and the design of the damping circuit was proposed to suppress the high-frequency ripples of the peak pulse current. An optimized coaxial discharge structure was designed to reduce the stray parameters in the main circuit. The design was verified through simulations and experiments, and the results demonstrated that the developed prototype successfully generated an ideal half-sinusoidal pulse current with a peak value of 15 kA, and a front pulsewidth of $2.5 ~\mu \text{s}$ at a repetition rate of 50 Hz. The pulse repetition stability is better than 0.1%. The final output was consistent with the theoretical analysis. The system can be applied in the CEPC positron source, which also provides a reference for the subsequent development of a positron source system at research facilities.
A polarized positron source for CEBAF

J. Dumas,J. Grames,E. Voutier

DOI: https://doi.org/10.48550/arXiv.0907.5348

2009-07-30

Accelerator Physics

Abstract:A compact polarized positron source for Jefferson Lab is discussed. This scheme relies upon a high polarization (85%), high current (1 mA), low-energy (<100 MeV) electron beam to generate polarized positrons in a conversion target via polarized bremsstrahlung and pair creation. GEANT4 is used to simulate source distributions suitable for a CEBAF-like injector with positron polarization ~60% and nano-Ampere intensity. An experiment to test this scheme is outlined.
System Design and Measurements of Flux Concentrator and Its Solid-State Modulator for CEPC Positron Source

Chinese Academy of Sciences,Li Xiao-Ping,University of Chinese Academy of Sciences,Chi Yun-Long,He Da-Yong,Li Jing-Yi,Sun Xian-Jing,Zhang Jing-Ru,Shang Lei

DOI: https://doi.org/10.1007/s41365-021-00904-z

2021-01-01

Abstract:Positron sources are one of the most important components of the injector of a circular electron positron collector (CEPC). The CEPC is designed as an e+e− collider for a Higgs factory. Its accelerator system is composed of 100-km-long storage rings and an injector. The design goal of the positron source is to obtain positron beams with a bunch charge of 3 nC. The flux concentrator (FC) is one of the cores of the positron source. This paper reports the design, development, and measurements of an FC prototype system. The prototype includes an FC and an all-solid-state high-current pulse modulator. Preliminary tests show that the peak current on the FC can reach 15.5 kA, and the peak magnetic field can reach 6.2 T. The test results are consistent with the theoretical simulation. The FC system fulfills the requirements of the CEPC positron source as well as provides a reference for the development of similar devices both domestically and abroad.
The Conversion of CESR to Operate as the Test Accelerator, CesrTA, Part 1: Overview

M.G. Billing

DOI: https://doi.org/10.1088/1748-0221/10/07/P07012

2015-05-05

Abstract:Cornell's electron/positron storage ring (CESR) was modified over a series of accelerator shutdowns beginning in May 2008, which substantially improves its capability for research and development for particle accelerators. CESR's energy span from 1.8 to 5.6 GeV with both electrons and positrons makes it ideal for the study of a wide spectrum of accelerator physics issues and instrumentation related to present light sources and future lepton damping rings. Additionally a number of these are also relevant for the beam physics of proton accelerators. This paper outlines the motivation, design and conversion of CESR to a test accelerator, CesrTA, enhanced to study such subjects as low emittance tuning methods, electron cloud (EC) effects, intra-beam scattering, fast ion instabilities as well as general improvements to beam instrumentation. While the initial studies of CesrTA focussed on questions related to the International Linear Collider (ILC) damping ring design, CesrTA is a very flexible storage ring, capable of studying a wide range of accelerator physics and instrumentation questions. This paper contains the outline and the basis for a set of papers documenting the reconfiguration of the storage ring and the associated instrumentation required for the studies described above. Further details may be found in these papers.

Accelerator Physics
Optimization of an hybrid positron source using channeling

I. Chaikovska,R. Chehab,H. Guler,P. Sievers,Xavier Artru,M. Chevallier,T. Suwada,M. Satoh,T. Kamitani,K. Furukawa,Fusashi Miyahara,K. Umemori,S. Jin

DOI: https://doi.org/10.1016/j.nimb.2017.03.012

2017-01-01

Abstract:The hybrid positron source made of a crystal-radiator, as a source of channeling radiation, and an amorphous converter is briefly described. Optimization of the heating effects and thermal shocks led to a granular converter made of small tungsten spheres. Simulation results with application to two linear collider projects CLIC and ILC are presented. A test operated with this kind of source at KEK is described and the results gathered last year, reported. Plans for the future are briefly described.
Positron Sources for Future High Energy Physics Colliders

P. Musumeci,C. Boffo,S. S. Bulanov,I. Chaikovska,A. Faus Golfe,S. Gessner,J. Grames,R. Hessami,Y. Ivanyushenkov,A. Lankford,G. Loisch,G. Moortgat-Pick,S. Nagaitsev,S. Riemann,P. Sievers,C. Tenholt,K. Yokoya

DOI: https://doi.org/10.48550/arXiv.2204.13245

2022-04-28

Abstract:An unprecedented positron average current is required to fit the luminosity demands of future $e^+e^-$ high energy physics colliders. In addition, in order to access precision-frontier physics, these machines require positron polarization to enable exploring the polarization dependence in many HEP processes cross sections, reducing backgrounds and extending the reach of chiral physics studies beyond the standard model. The ILC has a mature plan for the polarized positron source based on conversion in a thin target of circularly polarized gammas generated by passing the main high energy e-beam in a long superconducting helical undulator. Compact colliders (CLIC, C3 and advanced accelerator-based concepts) adopt a simplified approach and currently do not plan to use polarized positrons in their baseline design, but could greatly benefit from the development of compact alternative solutions to polarized positron production. Increasing the positron current, the polarization purity and simplifying the engineering design are all opportunities where advances in accelerator technology have the potential to make a significant impact. This white-paper describes the current status of the field and provides R\&D short-term and long-term pathways for polarized positron sources.

Accelerator Physics
The Conversion of CESR to Operate as the Test Accelerator, CesrTA, Part 4: Superconducting Wiggler Diagnostics

M.G. Billing,S. Greenwald,X. Liu,Y. Li,D. Sabol,E.N. Smith,C.R. Strohman,M.A. Palmer,D.V. Munson

DOI: https://doi.org/10.1088/1748-0221/11/10/T10009

2016-10-19

Abstract:Cornell's electron/positron storage ring (CESR) was modified over a series of accelerator shutdowns beginning in May 2008, which substantially improves its capability for research and development for particle accelerators. CESR's energy span from 1.8 to 5.6 GeV with both electrons and positrons makes it appropriate for the study of a wide spectrum of accelerator physics issues and instrumentation related to present light sources and future lepton damping rings. Additionally a number of these are also relevant for the beam physics of proton accelerators. This paper, the last in a series of four, describes the vacuum system modifications of the superconducting wigglers to accommodate the diagnostic instrumentation for the study of electron cloud (EC) behavior within wigglers. Earlier papers provided an overview of the accelerator physics program, the general modifications of CESR, the modifications of the vacuum system necessary for the conversion of CESR to the test accelerator, CesrTA, enhanced to study such subjects as low emittance tuning methods, EC effects, intra-beam scattering, fast ion instabilities as well as general improvements to beam instrumentation. While the initial studies of CesrTA focussed on questions related to the International Linear Collider damping ring design, CESR is a very versatile storage ring, capable of studying a wide range of accelerator physics and instrumentation questions.

Accelerator Physics
Massive Titanium Sublimation Pumping in the CESR Interaction Region

N. B. Mistry,R. Kersevan,Yulin Li

DOI: https://doi.org/10.1109/pac.1997.753273

2002-01-01

Abstract:The residual gas pressure within 30 m of the interaction point (IF) at the e/sup /spl plusmn// collider CESR is maintained in the low nanotorr range, despite the high gas loads produced by the intense flux of synchrotron radiation, in order to minimize the experimental backgrounds due to beam gas scattering. Within 12 m of the IP, the vacuum chambers incorporate large pumping plenums with massive titanium sublimation pumping to provide the necessary pumping speed and capacity. Operating experience over the last two years has shown that this method of pumping is efficient and inexpensive.
Polarized positron source with a Compton multiple interaction point line

I. Chaikovska,R. Chehab,O. Dadoun,P. Lepercq,A. Variola

DOI: https://doi.org/10.48550/arXiv.1405.2689

2014-05-12

Abstract:Positron sources are critical components of the future linear collider projects. This is essentially due to the high luminosity required, orders of magnitude higher than existing ones. In addition, polarization of the positron beam rather expands the physics research potential of the machine. In this framework, the Compton sources for polarized positron production are taken into account where the high energy gamma rays are produced by the Compton scattering and subsequently converted into the polarized electron-positron pairs in a target-converter. The Compton multiple Interaction Point (IP) line is proposed as one of the solutions to increase the number of the positrons produced. The gamma ray production with the Compton multiple IP line is simulated and used for polarized positron generation. Later, a capture section based on an adiabatic matching device (AMD) followed by a pre-injector linac is simulated to capture and accelerate the positron beam.

Accelerator Physics
Upgrade of the positron system of the ASACUSA-Cusp experiment

A. Lanz,C. Amsler,H. Breuker,M. Bumbar,S. Chesnevskaya,G. Costantini,R. Ferragut,M. Giammarchi,A. Gligorova,G. Gosta,H. Higaki,E. D. Hunter,C. Killian,V. Kraxberger,N. Kuroda,M. Leali,G. Maero,C. Malbrunot,V. Mascagna,Y. Matsuda,V. Mäckel,S. Migliorati,D. J. Murtagh,A. Nanda,L. Nowak,F. Parnefjord Gustafsson,S. Rheinfrank,M. Romé,M. C. Simon,M. Tajima,V. Toso,U. Uggerhøj,S. Ulmer,L. Venturelli,A. Weiser,E. Widmann,Y. Yamazaki,J. Zmeskal

2023-07-14

Abstract:The ASACUSA-Cusp collaboration has recently upgraded the positron system to improve the production of antihydrogen. Previously, the experiment suffered from contamination of the vacuum in the antihydrogen production trap due to the transfer of positrons from the high pressure region of a buffer gas trap. This contamination reduced the lifetime of antiprotons. By adding a new positron accumulator and therefore decreasing the number of transfer cycles, the contamination of the vacuum has been reduced. Further to this, a new rare gas moderator and buffer gas trap, previously used at the Aarhus University, were installed. Measurements from Aarhus suggested that the number of positrons could be increased by a factor of four in comparison to the old system used at CERN. This would mean a reduction of the time needed for accumulating a sufficient number of positrons (of the order of a few million) for an antihydrogen production cycle. Initial tests have shown that the new system yields a comparable number of positrons to the old system.

Atomic Physics,Plasma Physics
Undulator-Based Positron Source at 250 GeV CM Energy with Different Optical Matching Devices: Pulsed Flux Concentrator and Quarter Wave Transformer

Andriy Ushakov,Gudrid Moortgat-Pick,Sabine Riemann

DOI: https://doi.org/10.48550/arXiv.1801.08465

2018-01-26

Abstract:In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source. In this study the energy deposition in the pulsed flux concentrator (FC) of positron source is calculated for the ILC at 250 GeV center-of-mass energy. The peak energy of 33 J/g deposited by one beam pulse in the current design of the FC is above the limit for copper material. Several promising options were considered to solve the issue of overheating the FC: the quarter wave transformer (QWT) has a significantly bigger aperture and is considered as an valuable and safe alternative for the FC. Since the positron source with a QWT is expected to lead to a lower positron capture efficiency, also the expected positron yield was calculated in addition to the energy deposition in QWT.

Accelerator Physics
Modern High Intensity H- Accelerator Sources

Vadim Dudnikov

DOI: https://doi.org/10.48550/arXiv.1806.03391

2018-06-09

Plasma Physics

Abstract:A review of modern high intensity H- ion sources for accelerators is presented. The cesiation effect, a significant enhancement of negative ion emission from gas discharges with decrease of co-extracted electron current below negative ion current, was observed for the first time by inserting into the discharge chamber a compound with one milligram of cesium on July 1, 1971 in the Institute of Nuclear Physics (INP), Novosibirsk, Russia. This observation became the basis for the development of surface plasma negative ion sources (SPS). The efficiency of negative ion generation was increased by the invention of geometrical focusing. The magnetron-planotron with geometrical focusing SPS is discussed. The converter SPS is reviewed. Semiplanotron SPS is discussed. Penning discharge SPS, RF pulsed and CW SPS are reviewed. The history of negative ion source development is reviewed. Large development projects, including the SPS for the Large Hadron Collider (LHC) and for the International Thermonuclear Experimental Reactor (ITER) are being conducted. The development and fabrication of injectors with cesiated SPS has become a billion dollars scale industry.
POSITRON SOURCE FROM X-RAYS EMITTED BY PLASMA BETATRON MOTION

D. K. Johnson,C. E. Clayton,C. Huang,C. Joshi,W. Lu,K. A. Marsh,W. B. Mori,M. Zhou,I. Blumenfeld,C. D. Barnes,F. J. Decker,P. Emma,M. J. Hogan,R. Ischebeck,R. Iverson,N. Kirby

2006-01-01

Abstract:A new method for generating positrons has been pro- posed that uses betatron X-rays emitted by an electron beam in a high-K plasma wiggler. The plasma wiggler is an ion column produced by the head of the beam when the peak beam density exceeds the plasma density. The radial electric field of the beam blows out the plasma electrons transversely, creating an ion column. The focusing electric field of the ion column causes the beam electrons to exe- cute betatron oscillations about the ion column axis. At the proper plasma density, this leads to synchrotron radiation in the 1-50 MeV range. These photons strike a thin (.5Xo), high-Z target and create electron-positron pairs. Experi- mental results from work conducted at the Stanford Lin- ear Accelerator Center (SLAC), where a 28.5 GeV electron beam was used in a proof-of-principle demonstration of this scheme, were matched with a simulation model. This model was expanded to design a potential positron source, giving positron yields of 0.44 positrons/electron, a number that is close to the target goal of 1-2 positrons/electron for future positron sources.
Cascaded proton acceleration by collisionless electrostatic shock

t j xu,b f shen,x m zhang,l q yi,w p wang,l g zhang,jennifer c xu,x y zhao,yang shi,congbo liu,z k pei

DOI: https://doi.org/10.1063/1.4923455

IF: 2.2

2015-01-01

Physics of Plasmas

Abstract:A new scheme for proton acceleration by cascaded collisionless electrostatic shock (CES) is proposed. By irradiating a foil target with a moderate high-intensity laser beam, a stable CES field can be induced, which is employed as the accelerating field for the booster stage of proton acceleration. The mechanism is studied through simulations and theoretical analysis, showing that a 55 MeV seed proton beam can be further accelerated to 265 MeV while keeping a good energy spread. This scheme offers a feasible approach to produce proton beams with energy of hundreds of MeV by existing available high-intensity laser facilities. (C) 2015 AIP Publishing LLC.
An ECR hydrogen negative ion source at CEA/Saclay: preliminary results

R. Gobin,P-Y. Beauvais,O. Delferriere,R. Ferdinand,F. Harrault,J-M. Lagniel

DOI: https://doi.org/10.48550/arXiv.physics/0008143

2000-08-18

Abstract:The development of a high intensity negative ion source is part of a considerably larger activity presently undergoing at CEA Saclay in the field of high intensity linear accelerators. Preliminary studies toward the construction of a 2.45 GHz ECR H- ion source have been performed for few months. This new test bench takes advantage of our experience on the French high intensity proton source SILHI. In the new source, the high-energy electrons created in the ECR zone are trapped by a dipole magnetic filter. A rectangular 200 mm long plasma chamber and an intermediate iron shield are used to minimize the magnetic field in the extraction region. A second magnetic filter separates electrons and negative ions in a 10 kV extraction system. To reduce the electron/H- ratio, the plasma electrode is slightly polarized. The design allows future evolutions such as cesium injection, higher energy extraction and plasma diagnostics. The installation of the source is now in progress. The first helium plasma has been produced for few weeks to verify the electron separator behavior. The design, computations and the first results of the source are presented.

Accelerator Physics
Positron Source from Betatron X-Rays Emitted in a Plasma Wiggler

DK Johnson,CE Clayton,C Huang,C Joshi,W Lu,KA Marsh,W Mori,M Zhou,CD Barnes,FJ Decker,MJ Hogan,R Iverson,P Krejcik,C O'Connell,R Siemann,DR Walz,S Deng,T Katsouleas,P Muggli,E Oz

DOI: https://doi.org/10.1109/pac.2005.1590857

2005-01-01

Abstract:In the E-167 plasma wakefield accelerator (PWFA) experiments in the Final Focus Test Beam (FFTB) at the Stanford Linear Accelerator Center (SLAC), an ultra-short, 28.5 GeV electron beam field ionizes a neutral column of Lithium vapor. In the underdense regime, all plasma electrons are expelled creating an ion column. The beam electrons undergo multiple betatron oscillations leading to a large flux of broadband synchrotron radiation. With a plasma density of 3 × 1017cm-3, the effective focusing gradient is near 9 MT/m with critical photon energies exceeding 50 MeV for on-axis radiation. A positron source is the initial application being explored for these X-rays, as photo-production of positrons eliminates many of the thermal stress and shock wave issues associated with traditional Bremsstrahlung sources. Photo-production of positrons has been well-studied; however, the brightness of plasma X-ray sources provides certain advantages. In this paper, we present results of the simulated radiation spectra for the E-167 experiments, and compute the expected positron yield.
Proof-of-principle source for future colliders

N. Vallis,P. Craievich,M. Schär,R. Zennaro,B. Auchmann,H. H. Braun,M. I. Besana,M. Duda,R. Fortunati,H. Garcia-Rodrigues,D. Hauenstein,R. Ischebeck,E. Ismaili,P. Juranić,J. Kosse,A. Magazinik,F. Marcellini,T. Michlmayr,S. Müller,M. Pedrozzi,R. Rotundo,G. L. Orlandi,M. Seidel,N. Strohmaier,and M. Zykova

DOI: https://doi.org/10.1103/physrevaccelbeams.27.013401

2024-01-18

Physical Review Accelerators and Beams

Abstract:The PSI Positron Production ( P3 or P-cubed) experiment is a e+ source and capture system with the potential to increase by an order of magnitude the state-of-the-art e+ yield normalized to the drive linac energy, a highly desirable goal for future colliders. The experiment is framed in the FCC-ee injector study and will be hosted at SwissFEL, located at the Paul Scherrer Institute in Switzerland. This paper presents the P3 project at an advanced stage, with an emphasis on a capture system featuring a novel e+ matching device based on high-temperature superconducting solenoids, followed by two large aperture rf cavities surrounded by normal-conducting solenoids. The diagnostics design is also introduced, including monitors of charge, energy spectrum, and bunch-by-bunch longitudinal profile simultaneously for secondary e+ and e− . The last chapter of the text overviews the currently ongoing installation at SwissFEL, including the beam transfer line, rf network, radiation protection, and other relevant activities toward the operation with e+ in the coming years. https://doi.org/10.1103/PhysRevAccelBeams.27.013401 Published by the American Physical Society under the terms of the Creative Commons Attribution 4.0 International license. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI. Published by the American Physical Society

physics, particles & fields, nuclear
2X scaled Penning source developments

D. C. Faircloth,S. R. Lawrie,J. Sherman,P. Wise,M. O. Whitehead,T. Wood,T. Sarmento

DOI: https://doi.org/10.1063/1.5053326

2018-01-01

AIP Conference Proceedings

Abstract:To meet the full 2 ms 50 Hz 60 mA beam requirements for the Front End Test Stand (FETS) at the Rutherford Appleton Laboratory (RAL), a new cesiated Penning Surface Plasma Source (SPS) has been developed with a larger plasma volume with 2X (double) the linear dimensions of the standard ISIS source. This paper outlines the development work through preliminary tests and two prototypes. The latest results have demonstrated that operation at full duty cycle is possible but with a ‘noisy’ beam. A ‘clean’ beam was obtained at lower duty cycles and high cesium flux.
High-Intensity and High-Brightness Source of Moderated Positrons Using a Brilliant gamma Beam

C. Hugenschmidt,K. Schreckenbach,D. Habs,P.G. Thirolf

DOI: https://doi.org/10.1007/s00340-011-4594-0

2011-04-14

Abstract:Presently large efforts are conducted towards the development of highly brilliant gamma beams via Compton back scattering of photons from a high-brilliance electron beam, either on the basis of a normal-conducting electron linac or a (superconducting) Energy Recovery Linac (ERL). Particularly ERL's provide an extremely brilliant electron beam, thus enabling to generate highest-quality gamma beams. A 2.5 MeV gamma beam with an envisaged intensity of 10^15 s^-1, as ultimately envisaged for an ERL-based gamma-beam facility, narrow band width (10^-3), and extremely low emittance (10^-4 mm^2 mrad^2) offers the possibility to produce a high-intensity bright polarized positron beam. Pair production in a face-on irradiated W converter foil (200 micron thick, 10 mm long) would lead to the emission of 2 x 10^13 (fast) positrons per second, which is four orders of magnitude higher compared to strong radioactive ^22Na sources conventionally used in the <a class="link-external link-http" href="http://laboratory.Using" rel="external noopener nofollow">this http URL</a> a stack of converter foils and subsequent positron moderation, a high-intensity low-energy beam of moderated positrons can be produced. Two different source setups are presented: a high-brightness positron beam with a diameter as low as 0.2 mm, and a high-intensity beam of 3 x 10^11 moderated positrons per second. Hence, profiting from an improved moderation efficiency, the envisaged positron intensity would exceed that of present high-intensity positron sources by a factor of 100.

Nuclear Experiment,Accelerator Physics

CESR positron source

High Power Polarized Positron Source

Development of a Solid-State, High-Current, Repetitive Pulse Power System for Positron Source Prototype

A polarized positron source for CEBAF

System Design and Measurements of Flux Concentrator and Its Solid-State Modulator for CEPC Positron Source

The Conversion of CESR to Operate as the Test Accelerator, CesrTA, Part 1: Overview

Optimization of an hybrid positron source using channeling

Positron Sources for Future High Energy Physics Colliders

The Conversion of CESR to Operate as the Test Accelerator, CesrTA, Part 4: Superconducting Wiggler Diagnostics

Massive Titanium Sublimation Pumping in the CESR Interaction Region

Polarized positron source with a Compton multiple interaction point line

Upgrade of the positron system of the ASACUSA-Cusp experiment

Undulator-Based Positron Source at 250 GeV CM Energy with Different Optical Matching Devices: Pulsed Flux Concentrator and Quarter Wave Transformer

Modern High Intensity H- Accelerator Sources

POSITRON SOURCE FROM X-RAYS EMITTED BY PLASMA BETATRON MOTION

Cascaded proton acceleration by collisionless electrostatic shock

An ECR hydrogen negative ion source at CEA/Saclay: preliminary results

Positron Source from Betatron X-Rays Emitted in a Plasma Wiggler

Proof-of-principle source for future colliders

2X scaled Penning source developments

High-Intensity and High-Brightness Source of Moderated Positrons Using a Brilliant gamma Beam