Abstract:Introduction: There are significant individual variations in the polyethylene (PE) wear of Charnley total hip arthroplasty (THA) in published studies. This could be in part related to variations in hip joint kinematics with abnormal heating at the metal/PE interface. The objectives of our hip simulator experiment were: (1) to measure PE wear as a function of hip kinematics and temperature variations at the interface; (2) to compare ultra-high molecular weight polyethylene (UHMWPE) to latest generation highly cross-linked PE (XLPE). Hypothesis: Our hypothesis was that PE wear is correlated with temperature increases at the interface and thereby hip joint kinematics. Material and methods: A simulator study was performed with four UHMWPE cups (Initiale™, Amplitude, Valence, France) and two XLPE cups (X3, Stryker, Kalamazoo, Michigan, USA) subjected to 5 million cycles each. The temperature at the femoral head/cup interface was measured every 500 cycles and implant dimensions were measured every 1 million cycles. Results: The average temperature was 42°C for 1Hz and 50°C for 1.5Hz, no matter the type of PE tested. There was a large difference between UHMWPE and XLPE in their roughness, but no temperature variations or wear effects. Femoral head penetration after the first 1 million cycles was 0.18mm for the XLPE and 0.075mm UHMWPE on average. Between 1 and 5 million cycles, the penetration was less than 0.1mm per million cycles, with XLPE being similar to UHMPWE. Discussion: Our study found a significant temperature increase at the bearing interface as a function of frequency. But there was no correlation between temperature variations and PE degradation. However, shear stresses were under-estimated because our simulator could not reproduce abduction and adduction movements. Our hypothesis was not confirmed because PE deformation was not correlated to temperature variations. XLPE was not better than UHMWPE in the particular conditions of this study. Simulator studies are limited because of the lack of standards on cycling and the simulator bath. Level of evidence: III-prospective case-control study in vitro.

Effect of lipid absorption on wear and compressive properties of unirradiated and highly crosslinked UHMWPE: an in vitro experimental model

In-vitro oxidation model for UHMWPE incorporating synovial fluid lipids

Wear Mechanisms of Untreated and Gamma Irradiated Ultra-High Molecular Weight Polyethylene for Total Joint Replacements

[Crosslinking Modification of Ultra High Molecular Weight Polyethylene During Joint Arthroplasty].

Wear behaviour of cross-linked polyethylene assessed in vitro under severe conditions

Effects of Major Components of Synovial Fluid on the Morphology and Wear Rate of Polyetheretherketone (PEEK) Particles under an Accelerated Wear Process

Lipid index to quantify the absorbed lipids in retrieved UHMWPE components of joint arthroplasty

Highly Crosslinked vs Conventional Polyethylene Particles—An In Vitro Comparison of Biologic Activities

Do temperature variations at the bearing surface during gait affect polyethylene wear in Charnley low-friction arthroplasty of the hip? Simulator study comparing UHMWPE and highly cross-linked polyethylene

Comparative wear and wear debris under three different counterface conditions of crosslinked and non-crosslinked ultra high molecular weight polyethylene

Impact resistance and fractography in ultra high molecular weight polyethylenes

Structural modifications induced by compressive plastic deformation in single-step and sequentially irradiated UHMWPE for hip joint components

Wear Performance of UHMWPE and Reinforced UHMWPE Composites in Arthroplasty Applications: A Review

Anomalous Wear Behavior of UHMWPE During Sliding Against CoCrMo Under Varying Cross-Shear and Contact Pressure

Biotribological properties of UHMWPE grafted with AA under lubrication as artificial joint

Tribological properties of kaolin filled UHMWPE composites in unlubricated sliding

Natural Polyphenol-Stabilized Highly Cross-Linked UHMWPE for Joint Implants

Friction Properties at Polyethylene-Metal Interface in Total Joint Arthroplasty

Total Hip Wear Assessment: A Comparison Between Computational and In Vitro Wear Assessment Techniques Using ISO 14242 Loading and Kinematics

Wear Mechanism and Wear Debris Characterization of ULWPE in Multidirectional Motion

Development of an extremely wear-resistant ultra high molecular weight polyethylene for total hip replacements