Abstract:This paper describes the redesign of a high pressure rotor (with exit Mach number around 1.5) for the vaneless counter-rotating turbine by choosing adequate exit-to-throat width ratio. Based on the previous design analysis and test results, effects of the exit-to-throat width ratio on the performance of the transonic turbine cascade were proposed. In order to investigate the influence of the exit-to-throat width ratio on the performance of the turbine cascade, a flow model of the convergent-divergent turbine cascade was constructed by using the theory of Laval nozzle. Then a method on how to choose the adequate exit-to-throat width ratio for the turbine cascade was proposed. To validate the method, it was used to calculate the adequate exit-to-throat width ratio for the high pressure rotor of the vaneless counter-rotating turbine. The high pressure turbine rotor was redesigned with the new exit-to-throat width ratio. Numerical simulation results show that the isentropic efficiency of the redesigned vaneless counter-rotating turbine under the design condition has increased by 0.9% and the efficiencies under the off-design conditions are also improved significantly. On the original design, a group of compressional waves are created from the suction surface after about 60% axial chord in the high pressure turbine rotor. While on the new design the compressional waves are eliminated. Furthermore, on the original design, the inner-extending waves first impinge on the next high pressure turbine rotor suction surface. Its reflection is strong enough and cannot be neglected. However on the new design the inner-extending waves are weakened or even eliminated. Another main progress is that the redesigned high pressure turbine rotor is of practical significance. In the original rotor, a part of the blade (from 60% axial chord to the trailing edge) is thin leading to the intensity problem and difficult arrangement of the cooling system. In the new design, however, the thickness distribution of the rotor airfoil along the chord is relatively reasonable. The intensity of the rotor is enhanced. It is possible to arrange the cooling system reasonably.

A method to reduce the fluid mass transfer loss of rotating jet: A kind of microstructure design and research for wave rotor refrigerator

Numerical Study on the Effect of Nozzle Incident Angle on the Overall Performance of Gas Wave Refrigerator

Numerical study on cyclic driving force of enhanced refrigeration wave rotor based on optimized passage structure

Numerical study on zero-power operation strategy of radial gas wave refrigerator

Experimental investigation of pressure losses in a co-rotating cavity with radial inflow employing tubed vortex reducers with varied nozzles

Experimental and Numerical Investigation of a Novel Vortex Reducer in a Co-Rotating Cavity of Aeroengines

Investigation on non-equilibrium phase transition in wave rotor

Experimental Research on a Lightweight Miniature Wankel Compressor for a Vapor Compression Refrigeration System in Aerospace

Flow and Heat Transfer Characteristics of Coriolis-utilization Rotating Rectangular Smooth Cooling U-channel

Swirling and cavitating flow suppression in a cryogenic liquid turbine expander through geometric optimization

Research on the application performance of the corrugated structures in gas wave tubes

Influence of exit-to-throat width ratio on performance of high pressure convergent-divergent rotor in a vaneless counter-rotating turbine

Influence of the Internal Structures on the Performance of Sweeping Jet Film Cooling

Wave rotor as a pressure exchanger for lower rotational speed and lower shaft work in a supercritical carbon dioxide Brayton cycle

Heat Transfer and Flow Characteristics of U-shaped Cooling Channels with Novel Wavy Ribs under Stationary and Rotating Conditions

High-performance Marangoni hydrogel rotors with asymmetric porosity and drag reduction profile

Analysis, modeling and simulations of an innovative sliding vane rotary compressor with a rotating cylinder

Rotation Effect on Flow and Heat Transfer for High-Temperature Rotor Blade in a Heavy Gas Turbine

NUMERICAL INVESTIGATION ON LOSS MECHANISM AND PERFORMANCE IMPROVEMENT FOR A ZERO INLET SWIRL TURBINE ROTOR

The Influence of Structure Optimization on Vortex Suppression and Energy Dissipation in the Draft Tube of Francis Turbine

Research on loss differences and thermal optimisation of submerged cryogenic high‐speed permanent magnet motors