Abstract:The economic exploitation of unconventional gas and oil in deep shale relies closely on effective hydraulic fracturing stimulations. However, the fracturing operations of deep shale reservoirs face challenges of insufficient fracture growth and a rapid decline in productivity due to the increasing in situ stress level. In addition, the shale strata on the margin of the Sichuan Basin are frequently folded and faulted, and the change in bedding inclinations significantly complicates the process of hydraulic fracturing. The investigation of the combined effect of the in situ stress level and bedding anisotropy on the hydraulic fracture configuration is vital for fracturing engineering design. To analyze this, we conducted hydraulic fracturing tests on shale cores to simulate the hydraulic fracture initiation and growth from a horizontally positioned perforation. By using acoustic emission detection and CT scans, the influence of natural stress levels and the angle of the shale’s bedding on the process of hydraulic fracturing in shale and the resulting fracture geometry were analyzed. The results showed that the area of hydraulic fracture under a higher stress level (σ1 = 50 MPa, σ3 = 40 MPa) was about 13%~23% smaller than that created under the lower stress level (σ1 = 30 MPa, σ3 = 20 MPa) when the bedding angle was smaller than 60°. With the increase in bedding angle, the curves of the fracture area and fracture network index under two different stress levels presented similar decreasing trends. Also, the time from micro-crack generation to sample breakdown was significantly reduced when the bedding orientation changed from the horizontal to vertical position. The increasing stress level significantly increased the breakdown pressure. In particular, the fracturing of shale samples with bedding angles of 0° and 30° required a higher fluid pressure and released more energy than samples with larger bedding inclinations. Additionally, the measurement of the sample radial deformation indicated that the hydraulic fracture opening extent was reduced by about 46%~81% with the increasing stress level.

Experimental and numerical study of measuring in-situ stress in horizontal borehole by hydraulic fracturing method

Research and application of small-diameter hydraulic fracturing in situ stress measurement system

Experimental study on hydraulic fracturing properties of elliptical boreholes

Experimental study on the influence of horizontal stress difference coefficient on coal rock fracture

Vertical Tunneling in China-A Case Study of a Hydraulic Tunnel in Beihai

Rapid In-Situ Stress Measurement in Vertical Borehole Based on Borehole Diametrical Deformation Analysis

Study on the Stress and Deformation of Surrounding Rock and Support Structure of Super Large Section Tunnels Based on Different Excavation Methods

Study on the Shadow Effect of the Stress Field around a Deep-Hole Hydraulic-Fracturing Top-Cutting Borehole and Process Optimization

Determination of geo-stress in deep strata incorporating borehole diametral deformation measurement and overcoring

Research on stress field inversion and large deformation level determination of super deep buried soft rock tunnel

Study on Stress Characteristics of Multi-arch Tunnel Lining under Weak Surrounding Rock Conditions Based on Field Measurement

Investigation of the Stress and Strain Distribution in the Surrounding Soil of a Tunnel Induced by the Double-Heading at Bottom Method

Anelastic strain recovery in situ stress measurement method and its application prospect in underground mines

3D numerical analysis of stability and onset of hydraulic fracture in the vertical‐oblique‐horizontal wells under wide range of in situ stresses

Physical Simulation Experiments of Hydraulic Fracture Initiation and Propagation under the Influence of Deep Shale Natural Fractures

Combined Effect of In Situ Stress Level and Bedding Anisotropy on Hydraulic Fracture Vertical Growth in Deep Marine Shale Revealed via CT Scans and Acoustic Emission

Research on in Situ Stress Inversion of Deep‐buried Tunnel Based on Pressure/tension Axis Mechanism and Geological Structure

In situ Stress–Coal Structure Relationship and Its Influence on Hydraulic Fracturing: A Case Study in Zhengzhuang Area in Qinshui Basin, China

Construction practice of water conveyance tunnel among complex geotechnical conditions: a case study

Quantitative prediction of the drilling azimuth of horizontal wells in fractured tight sandstone based on reservoir geomechanics in the Ordos Basin, central China

Characterization of the High Geostress Field in Deep-Buried Diversion Tunnels and Its Inversion Analysis