Abstract:The incidence of screw loosening, migration, and pullout caused by the insufficient screw-bone fixation stability is relatively high in clinical practice. To solve this issue, the auxetic unit-based porous bone screw (AS) has been put forward in our previous work. Its favorable auxetic effect can improve the primary screw-bone fixation stability after implantation. However, porous structure affected the fatigue behavior and in vivo longevity of bone screw. In this study, in vitro fatigue behaviors and in vivo osseointegration performance of the re-entrant unit-based titanium auxetic bone screw were studied. The tensile-tensile fatigue behaviors of AS and nonauxetic bone screw (NS) with the same porosity (51%) were compared via fatigue experiments, fracture analysis, and numerical simulation. The in vivo osseointegration of AS and NS were compared via animal experiment and biomechanical analysis. Additionally, the effects of in vivo dynamic tensile loading on the osseointegration of AS and NS were investigated and analyzed. The fatigue strength of AS was approximately 43% lower while its osseointegration performance was better than NS. Under in vivo dynamic tensile loading, the osseointegration of AS and NS both improved significantly, with the maximum increase of approximately 15%. Preferrable osseointegration of AS might compensate for the shortage of fatigue resistance, ensuring its long-term stability in vivo. Adequate auxetic effect and long-term stability of the AS was supposed to provide enough screw-bone fixation stability to overcome the shortages of the solid bone screw, developing the success of surgery and showing significant clinical application prospects in orthopedic surgery. STATEMENT OF SIGNIFICANCE: This research investigated the high-cycle fatigue behavior of re-entrant unit-based auxetic bone screw under tensile-tensile cyclic loading and its osseointegration performance, which has not been focused on in existing studies. The fatigue strength of auxetic bone screw was lower while the osseointegration was better than non-auxetic bone screw, especially under in vivo tensile loading. Favorable osseointegration of auxetic bone screw might compensate for the shortage of fatigue resistance, ensuring its long-term stability and longevity in vivo. This suggested that with adequate auxetic effect and long-term stability, the auxetic bone screw had significant application prospects in orthopedic surgery. Findings of this study will provide a theoretical guidance for design optimization and clinical application of the auxetic bone screw.

Stress concentration in the auxetic porous screw and its fatigue behavior

In vitro fatigue behavior and in vivo osseointegration of the auxetic porous bone screw

FE Analysis of Stress Concentrations in Composite Plates with Multiple Holes for Zigzag Multi-Fastened Joints

Fatigue assessment of CFST joints using the effective notch stress approach

Fatigue Behavior of Short-Headed Studs Embedded in Ultra-high Toughness Cementitious Composites (UHTCC)

Three-dimensional finite element analysis of stress distribution on short implants with different bone conditions and osseointegration rates

COMPARISON OF FATIGUE BEHAVIORS OF SPINAL IMPLANTS UNDER PHYSIOLOGICAL SPINAL LOADS: A FINITE ELEMENT PILOT STUDY

Influence of connection design and material properties on stress distribution and fatigue lifetime of zygomatic implants: A finite element analysis

Hot Spot Stress and Fatigue Behavior of Bird-Beak SHS X-joints Subjected to Brace In-Plane Bending

Aspects Of The Residual-Stress Field At A Notch And Its Effect On Fatigue

Fatigue Notch Strengthening Effect of Nickel-based Single Crystal Superalloys under Different Stress Ratios

Bioinspired 3D‐Printed Auxetic Structures with Enhanced Fatigue Behavior

Finite Element Analysis of Atlantoaxial Screws and Plates Instrument for Upper Cervical Spine Stability

Optimal design and biomechanical analysis of sandwich composite metal locking screws for far cortical locking constructs

An enhanced stress field intensity approach for fatigue life assessment combining notch and size effect

Expressions for Stress Concentration Factors for T-Joints of Hollow and Concrete-Filled Square Cross-Sections for In-Plane Axial and Bending Loads

Empirical modeling of stress concentration factors using finite element analysis and artificial neural networks for the fatigue design of tubular KT‐joints under combined loading

Effect of design parameters on auxetic behavior and stiffness of additively manufactured 316L stainless steel

Comparison of the continuum damage and fracture mechanics in fatigue assessment of components containing residual stresses

A Structural Stress Approach Accounting for Notch Effects on Fatigue Propagation Life: Part I Theory

Stress Concentration Factors and Fatigue Behavior of Square Bird-Beak Shs T-Joints under Out-Of-Plane Bending