Abstract:In recent years, square hollow section (SHS) joints with concrete-filled square hollow section (CFSHS) chords have increasingly been used in truss bridges where the fatigue life reliability is a critical issue. In this paper, a finite element analysis was performed to investigate the SCFs in SHS-CFSHS T-joints under in-plane bending in the brace, axial force in the chord and in-plane bending in the chord. The finite element models were developed and validated with experimental results. Then a parametric study was conducted with a reasonable range of three key non-dimensional parameters, i.e., β (width ratio between brace and chord), 2γ (width–to–wall thickness ratio of the chord) and τ (wall thickness ratio between brace and chord). Consequently, the stress concentration factor formulae for the fatigue design of SHS-CFSHS T-joints were proposed through multiple regression analysis. For in-plane bending in the brace, the maximum stress concentration factors were found at lines B and C for thick-walled chords (2γ = 25.0), while the stress concentration factors at all the lines need to be checked for thin-walled chords (2γ < 16.0). Under axial force in the chord and in-plane bending in the chord, only stress concentration factors at lines C and D needed to be considered. A comparison of stress concentration factors between SHS-SHS and SHS-CFSHS joints showed reductions of 10~26% and 14~31% in stress concentration factors in SHS-CFSHS joints under axial force in the brace and in-plane bending in the brace, respectively. In addition, it showed a general increase in stress concentration factors in SHS-CFSHS joints under axial force and in-plane bending in the chord. This reduction is attributed to the reduction in chord face deformation benefiting from the in-filled concrete. Meanwhile, the stress concentration factors caused by loads in the chord are much lower than those caused by loads in the brace. This work complements earlier studies on SHS-CFSHS T-joints under axial force.

FE Analysis of Stress Concentrations in Composite Plates with Multiple Holes for Zigzag Multi-Fastened Joints

Strength Analysis Methods for High Stress Gradient Parts in Composite Structures Ensuring Design Office Requirements

Numerical Analysis and Punching Shear Fracture Based Design of Longitudinal Plate to Concrete-Filled CHS Connections

Probabilistic Analysis of Stress Concentration Factor of an Orthotropic Steel Bridge with FBG-Based Structural Health Monitoring System *

Structural analysis of sandwich plates with variable stiffness composite skins and functionally graded cores using refined zig-zag theory

Tensile Behavior of Double-Hole CFRP Composite with Different Holes Position

Stress, damage, and fatigue performance analysis of CFRP/Al double-sided countersunk riveted joints with variable rivet-hole clearance

Numerical analysis of fiber reinforced composite material for structural component application

Analytical studies and numerical predictions of stresses in shear joints of layered composite panels for aerospace applications

Expressions for Stress Concentration Factors for T-Joints of Hollow and Concrete-Filled Square Cross-Sections for In-Plane Axial and Bending Loads

Fatigue-driven failure criterion for progressive damage modelling and fatigue life prediction of composite structures

Stress Analysis on Finite Orthotropic Composite Plate with a Central Hole under Biaxial Loading

Experimental and Finite Element Research on the Failure Mechanism of C/C Composite Joint Structures under Out-of-Plane Loading

Finite Element Analysis for the Fatigue Behavior of Steel Plates Strengthened with CFRP Plates

Failure Analysis of Hat-Stringer-Stiffened Aircraft Composite Panels under Four-Point Bending Loading

Experimental and numerical study of the effects of fiber orientation on stress concentration of CFRE

Tension-Compression Fatigue Induced Stress Concentrations in Woven Composite Laminate

Failure analysis and experimental study on bolted composite joints based on continuum damage mechanics

Prediction of Stress Concentration Factor Distribution for Multi-Planar Tubular DT-joints under Axial Loads

A Combined Experimental and Computational Analysis of Failure Mechanisms in Open-Hole Cross-ply Laminates under Flexural Loading

Computational Fatigue Life Analysis of Carbon Fiber Laminate