Abstract:The steel, whose nominal yielding strength f(y) is greater than or equal to 460 MPa, is generally referred to as high strength steel (HSS). Through the comparison with conventional strength steel (CSS) members, HSS members are more vulnerable to local buckling since the component plates are usually designed to be more slender in order to exploit higher material strength. The different mechanical properties between HSS and CSS, including yielding strength, ductility and so on, may lead to different local buckling behavior of steel members. However, little guidance is applicable in existing standards for the stability design of HSS members. In this paper, elaborate finite element (FE) models of HSS welded I-section beams under the loading conditions of uniform moment (four-point loading) and moment gradient (three-point loading) were developed by means of the general-purpose FE software package and validated against the available test results. Continuous lateral supports were ideally applied to restrict the occurrence of coupling with overall lateral-torsional buckling. Comprehensive parametric analyses on key parameters containing the plate width-to-thickness ratio and the steel material properties were further conducted, reflecting the influence of these parameters on the mechanical performance of local stability. Through this work, the variation rules on rotation capacity and postbuckling resistance of HSS welded I-section beams with plate width-to-thickness ratio and steel nominal yielding strength were clarified. Taking into account the interaction of local buckling modes between flanges and webs, new cross-section classification of HSS welded I-section beams was proposed based on the FE analysis results. After the introduction of the concept of interactive local slenderness, the design methods of postbuckling ultimate moment resistance for HSS welded I-section beams subjected to uniform moment and moment gradient were also proposed, which were assessed by comparing the design results with the ones obtained from the corresponding design approaches in Eurocode 3, ANSI/AISC 360-16 and GB 50017-2017. And the reliability of the new proposals was also confirmed by further statistical analysis.

A Theoretical Calculation Model of H-Section Steel Members for Biaxial Bending Moments

Load-Carrying Capacity and Practical Calculation Method for Hollow Cylinder Joints Connected with H-Shaped Beams

Load-carrying Capacity and Practical Calculation Method of Welded Hollow Spherical Joints with Square Steel Tubes Subjected to Combined Axial Forces and Biaxial Bending Moments

Numerical Simulation Analysis and the Program for Steel-Concret Composite Long Column in Eccentricaly-loaded

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Numerical Investigations on Elastic Buckling and Hysteretic Behavior of Steel Angles Assembled Buckling-Restrained Braces

Design for local buckling behaviour of welded high strength steel I-sections under bending

Finite Element Analysis Model for Reinforced Concrete Columns Subjected to Biaxial Eccentric Compression

Numerical Investigation and Design of Thin-Walled Complex Section Steel Columns

Machine learning (ML) based models for predicting the ultimate bending moment resistance of high strength steel welded I-section beam under bending

Experimental and Analytical Study on Local Buckling Behavior of High Strength Steel Welded I-Section Beams

Cross-section behaviour of cold-formed high strength steel irregular hexagonal hollow section stub columns under combined compression and bending

Analysis and Design Method on Local Buckling Behavior of 960 MPa High Strength Steel Columns under Axial Compression

Mechanical Behaviour of Circular Steel-Reinforced Concrete-Filled Steel Tubular Members under Pure Bending Loads

Local and Global Interactive Buckling Capacity of Thin-Walled Box-Section Members of BS700 High-Strength Steel under Axial Compression

Experimental and Constitutive Model Study of Structural Steel under Cyclic Loading

Constitutive Model for Full-Range Elasto-Plastic Behavior of Structural Steels with Yield Plateau: Formulation and Implementation

Preliminary Discussion on Mechanical Performance of Concrete-Filled Rectangular Steel Tube Members under Bi-axial Compression and Bending

FINITE ELEMENT ANALYSIS AND DESIGN METHOD STUDY ON THE LOCAL BUCKLING OF 460 MEGAPASCAL HIGH STRENGTH STEEL I-SECTION COLUMNS UNDER AXIAL COMPRESSION

Simulating the hysteretic behaviour of thin-walled H-Section steel members using the geometrically exact beam theory

Postbuckling Resistance of High Strength Steel Welded I-section Beams Based on Interactive Slenderness