Abstract:<p>As bonded components of many industrial structures are inevitably under bending fatigue loads, it is essential to improve their mechanical behavior under these loads. This paper aims to investigate the influence of adding graphene and silica nano-particles to Araldite 2015 adhesive on the fatigue behavior of aluminum-to-composite bonded single lap joints (SLJs) by a novel fixture under four-point bending. Four adhesive groups were prepared: I) neat, II) nano silica-reinforced, III) nano graphene-reinforced (groups II and III include 0.5 wt%, 1.0 wt%, and 1.5 wt% contents), and IV) a mixture of these particles (0.5 wt% of each particle). Besides, all nano-reinforced groups were prepared with similar processing steps including magnetic stirring (30 min duration, speed of 180 rpm) followed by ultrasonic mixing (1 h duration) and vacuum oven drying. Tensile tests indicated that the tensile strength of the graphene-reinforced bulk specimens was greater than that of silica-reinforced ones for 0.5 wt% and 1 wt% of filler contents. Also, the average static failure load (ASFL) of the graphene-reinforced SLJs under four-point load was greater than that of silica-reinforced joints for 0.5 wt% and 1 wt%, and it was lower than that of the silica-reinforced specimens for 1.5 wt% of particle contents due to the presence of more agglomeration of nano graphene particles in the adhesive. Then, for maximum fatigue loads of 40%–70% of ASFL, and load ratios of R = 0.5, 0, and −1, load vs. life cycle curves were examined for all SLJ groups. The ASFL and fatigue life of group IV SLJs (mixture of 0.5 wt% of each particle) were improved compared to the joints reinforced by separate usage of each particle with 1 wt% content. Using backface strain measurements, the influence of adding nano-particles on retarding the crack initiation phase was discussed under different load conditions. Finally, optical microscope observations indicated that adding nano-particles changes the failure mode from adhesive to cohesive. The major reinforcing mechanisms encountered in this research were interpreted by scanning electron microscopy.</p>

Numerical investigation of the strength of Al/GFRP adhesive bonding under tensile loading

Numerical and experimental analysis of Al/GFRP joint for optimization of adhesive bonding strength using response surface method by considering surface patterning of the joints

Experimental Study on Dynamic Behavior of GFRP-to-concrete Interface

The effect of abrading treatment method on the bonding surface characteristics and fracture behavior of glass fiber-epoxy composite adhesive joints

Study on Effects of Pre-Treatment and Surface Roughness on Tensile-Shear Strength of 2060 Al–Li Alloy Adhesive Joints

The influence of GNP and nano-silica additives on fatigue life and crack initiation phase of Al-GFRP bonded lap joints subjected to four-point bending

Experimental study of the influence of adhesive reinforcement in lap joints for composite structures subjected to mechanical loads

Investigation on shear and fatigue performance of CFRP/aluminum alloy single-lap adhesive joint

Effects of surface roughness parameters on the shear strength of AA 6061-T6 aluminium alloy in structural adhesive bonding applications

Effect of adhesive thickness and surface roughness on the shear strength of aluminium one-component polyurethane adhesive single-lap joints for automotive applications

Experimental Investigation of the Mechanical Behavior of Aluminum Adhesive Joints under Mixed-Mode Loading Conditions

Influence of Adherend Surface Roughness on the Adhesive Bond Strength

The Effect of Surface Substrate Treatments on the Bonding Strength of Aluminium Inserts with Glass-Reinforced Poly(phenylene) Sulphide

Synergistic effect of surface treatment and adhesive type on bonding performance of thin Al6061 joints for automotive applications

Mechanical behavior investigation of fused deposition modeling joints by using different bonding geometry with variable adhesive thickness

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

Experimental and Numerical Study of Adhesively and Bolted Connections of Pultruded GFRP I-Shape Profiles

Effects of Surface Modification and Graphene Nanoplatelet Reinforcement on Adhesive Joint of Aluminium Alloys

Strength and failure mechanism of single-lap magnesium-basalt fiber metal laminate adhesively bonded joints: Experimental and numerical assessments

Influence оf Surface Preparation of Aluminum Alloy AW-5754 аnd Stainless Steel X5CRNI18-10 оn the Properties оf Bonded Joints

Influence of raw material surface roughening on the lap shearing strength and failure behavior of adhesively bonded aluminum joints