Abstract:The deformation behavior of a radially forged 2A50 aluminum alloy was investigated by thermal compression test at high-temperature solid (300–500 °C) and semi-solid (565–585 °C) states with strain rates of 0.01–0.5s–1. A strain-compensated Arrhenius constitutive equation was established to describe the relationship between flow stress and compression parameters. The inhomogeneous deformation and microstructure evolution of the specimen were explored. Results reveal that the strain-compensated Arrhenius model can accurately predict experimental flow stress in both two temperature states. In the high-temperature solid state, the equilibrium between the softening effect (dynamic recovery and dynamic recrystallization) and work hardening leads to a steady stage of the flow curves after peak. In the semi-solid temperature, the softening mechanisms mainly include the high level of dynamic recrystallization (DRX), lubrication of liquid phases, and partial collapse of solid-phase skeleton, contributing to a declining stage of flow stress after peak. Strain and temperature profoundly influence DRX. At high-temperature solid state, coarse and elongated grains predominate in the regions with small strain, whereas DRX and numerous subgrains massively occur in the regions with large strain. The entire sample compressed in semi-solid temperature is subjected to DRX, attributed to the elevated temperature compared to the high-temperature solid state. Fine DRX grains are concentrated at the center of the large deformation zone (with large strain) due to the frequent DRX. Elevating semi-solid temperature leads to the formation of large equiaxed grains. DRX facilitates the weakening of deformed textures, demonstrated by the presence of deformed textures (<111> and <100>//X0 fiber textures, <111>//Z0 fiber texture, and {110}<111> texture) in the sample at high-temperature solid state, contrasted with the absence of pronounced preferred orientation in semi-solid compressed sample.

Investigation on the compression properties of semi-solid Be-Al alloy

Deformation Behavior of Aluminum Alloy during Semi-Solid Compression

Deformation Behavior of Semi-Solid Zn–Al Alloy Filler Metal During Compression

Effects of Compression Parameters on Deformation Behaviors of Semi-Solid ZA27 Alloys

Semi-solid compression of 2A14 alloy with high solid fraction: rheology, constitutive equation and microstructure

Deformation Behaviour and Microstructures of Semi-Solid A356.2 Alloy Prepared by Radial Forging Process During High Solid Fraction Compression

Experimental study on semi-solid micro-compression of ZL101 alloy

Microstructure and mechanical properties of powder metallurgy Be/Al alloy

Hot compression behaviors and microstructural evolution of Be-38wt.%6061Al

Mechanical behaviour of Al/Al2O3 composite in pseudo-semi-solid state during isothermal compression

Mechanical Analysis of Semi-Solid Metals Shear Deformation During Compression

Influence of Soaking Time and Loading Rate on Semi-solid Compression of Porous Al-4Cu-Mg Alloy

Investigation on Compressive Behavior of Cu-35Ni-15Al Alloy at High Temperatures

Al/Al2O3 composite mechanical behaviour of compression in pseudo-semi-solid sate

Microstructural evolution and anisotropic tensile properties of a bimodal 6A02 Al semi-solid billet

Study of the Rheological Behavior of Al2O3/Al Composites in Pseudo-semi-solid State

Deformation Behavior of Cu-3.8Be Alloy Under Isothermal Compression Conditions

Deformation Behavior and Microstructure Characterization of the Radially Forged 2A50 Aluminum Alloy at High-Temperature Solid and Semi-Solid States

Fatigue Property for the Powder Metallurgy Beryllium-Aluminum Composite Materials

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Effect of beryllium addition and heat treatment on the microstructure and mechanical properties of the 15%Mg2Si/Al-8Si composite