Abstract:The stress wave generated by impact or dynamic load will produce significant reflection and transmission at the rock coal or rock interface during the propagation process. This will produce dynamic effects such as dynamic tensile, stress superposition and mutation. These dynamic effects will lead to obvious vibration at the interfaces, which is a key factor leading to dynamic damage and the failure of coal and rock mass. In the process of underground engineering excavation, the dynamic damage of a series of layered rock masses is one of the important factors causing geological disasters. Based on the two–dimensional similar material simulation experiment, the coal and rock mass combined of five layers of fine sandstone, medium sandstone, coal, coarse sandstone and mudstone was taken as the research object, and single and multi-point excitation (synchronous/step-by-step) were used to test the time–history vibration curves of rock–coal and rock–rock interfaces under impact load. It was concluded that the change of extreme value of vibration amplitude presented two stages: first increase, and then attenuation. Most of them required 2.25 cycles to reach the peak value, and the dynamic attenuation of amplitude conformed to the law of exponential. Based on Fast Fourier transform (FFT), the spectrum structures of the amplitude–frequency of interface vibration were studied, and the two predominant frequencies were 48.9~53.7 Hz and 92.4 Hz, respectively. Based on the Hilbert-Huang transform and energy equation, 5~7 vibration modes (IMF) were obtained by decomposing the time–history curves. The three modes, IMF1, IMF2, and IMF3, contained high energy and were effective vibration modes. IMF2 accounted for the highest proportion and was the main vibration mode whose predominant frequencies were concentrated in 45.6~50.2 Hz. Therefore, IMF2 played a decisive role in the whole vibration process and had an important impact on the dynamic response, damage and failure of coal and rock mass. In real conditions, the actual predominant frequencies can be converted according to the size and mechanical properties of the coal and rock mass, and the vibration response characteristics of the interfaces between coal and rock mass under impact load were preliminarily revealed. This study can provide reference for monitoring and early warning of coal and rock dynamic disasters, prevention and control of coal and gas outburst and technical development.

Influence of coal-rock interface inclination on the damage and failure law of original coal-rock combination

The strength characteristics and competitive failure mechanism of primary coal-rock combination considering interface damage quantity

Simulation of Mining-Induced Ground Damage Using Orthogonal Experiments to Determine Key Parameters of Super-Large Coalface: A Case Study in Shendong Coalfield in China

Damage and energy characteristics of coal rock combinations with inclined coal seams under axial loading

Failure energy evolution of coal–rock combination with different inclinations

Experimental study on the effects of interface dip angle on deformation failure of combined limestone–coal specimens

Experimental Study on Mechanical Properties and Microcrack Fracture of Coal Specimens under the Coupling of Loading Rate and Compression–Shear Loads

Experimental Study on Mechanical Properties and Energy Evolution Law of Coal-Rock Composite Structure under Different Interface Connection Modes

Experimental Study on the Influence of Lithology and Rock-Coal Height Ratio on Mechanical Properties and Impact Effect of Combined Body

Vibration Response of the Interfaces in Multi-Layer Combined Coal and Rock Mass under Impact Load

Characterization of the Time–Space Evolution of Acoustic Emissions from a Coal-like Material Composite Model and an Analysis of the Effect of the Dip Angle on the Bursting Tendency

Evolution law of mining-induced overburden stratum stress and fracture fields in inclined coal seam

Mechanical behaviors and failure characteristics of coal-rock combination under quasi-static and dynamic disturbance loading: a case based on a new equipment

Coupling Influence of Inclination Angle and Moisture Content on Mechanical Properties and Microcrack Fracture of Coal Specimens

The failure behavior of coal-rock combined body under compression-shear loading

Failure characteristics and fracture mechanism of overburden rock induced by mining: A case study in China

Simulation Experimental Investigations into the Mechanical Response and Failure Mechanisms of Coal–Rock Combinations

Damage evolution of rock containing prefabricated cracks based on infrared radiation and energy dissipation

Experimental and numerical investigation on the mechanical characteristics and failure mechanism of cracked coal & rock-like combined sample under uniaxial compression

Research on strain softening constitutive model of coal-rock combined body with damage threshold

Study on Progressive Instability Characteristics of Coal-Rock Composite Structure with the Different Height Ratios