Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Electrochemical hydrogen storage performance of Mg3GeNi2 alloy

Enhanced Electrochemical Performance of Mg2ni Alloy Prepared by Rapid Quenching in Magnetic Field

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

Characteristics of Hydride Electrodes Using Mg-Ti-Ni-Co-Al-based Alloys Synthesized by Mechanical Milling

Electrochemical features of Ce2Ni7-type La0.65Nd0.15Mg0.25Ni3.20M0.10 (M = Ni, Mn and Al) hydrogen storage alloys for rechargeable nickel metal hydride battery

Effect of the La/Mg ratio on the structure and electrochemical properties of LaxMg3-xNi9 (x = 1.6 -2.2) hydrogen storage electrode alloys for nickel-metal hydride batteries

Influence of Ball-milling with Ni Powder on the Phase Structure and Electrochemical Hydrogen Storage Properties of Mg17Al12 Alloy

La–Mg–Ni ternary hydrogen storage alloys with Ce2Ni7-type and Gd2Co7-type structure as negative electrodes for Ni/Mh batteries

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

The electrochemical properties of LaxMg3-xNi9 (x = 1.0-2.0) hydrogen storage alloys

Electrochemical properties and Rietveld analysis of Multicomponent MlβMm1-β (NiCoMnTi)5 hydrogen storage alloys (2) Rietveld analysis

Effects of the Amount of Mg Impurity on the Electrochemical Properties of Ml(NiCoMnTi)5 Hydrogen Storage Alloy

Improving hydrogen-induced crystallization and electrochemical hydrogen storage properties of MgNi amorphous alloy with CoB addition

The structural and electrochemical properties of La2Mg(Ni0.8-xCo0.2Alx)9 (x = 0-0.03) hydrogen storage electrode alloys

Enhanced high-rate performance of ball-milled MmNi3.55Co0.75Mn0.4Al0.3 hydrogen storage alloys with graphene nanoplatelets

Study on the Microstructure and the Electrochemical Properties of Ml0.7Mg0.2Ni2.8Co0.6 Hydrogen Storage Alloy

Effect of Nanostructure and Partial Substitution on Gas Absorption and Electrochemical Properties in Mg2Ni-based Alloys

Microstructural Investigation of Electrochemical Hydrogen Storage in Amorphous Mg–Ni–La Alloy