Abstract:Commercially pure titanium specimens are subjected to three different treatments, and their bioactivity are evaluated by immersing the specimens in a simulated body fluid (SBF, Kokubo's recipe) for various periods up to 7 days, with particular attention being paid to the differences in apatite deposition between surfaces open to SBF and surfaces in contact with the container's bottom. The treatment with a H(2)O(2)/HCl solution at 80 degrees C for 30 min followed by heating at 400 degrees C for 1 h produces an anatase titania gel layer on the specimen surface. This gel layer deposits apatite both on the contact and on open surfaces, and apatite deposition ability does not change with pre-staking in distilled water. The treatment with a NaOH solution at 60 degrees C for 3 days produces a sodium titanate gel layer. This gel layer can deposit apatite only on the contact surface, and the apatite deposition ability is completely lost after 1 day of pre-staking in distilled water. It is concluded, therefore, that the bioactivity of the titania gel originates from the favorable structure of the gel itself while the bioactivity of the sodium titanate gel depends heavily on ion release from the gel. The third treatment, a simple heat treatment at 400 degrees C for 1 h, produces a dense (not porous) oxide layer on the specimen surface. The specimens can deposit apatite on the contact surface after only 3 days of staking in SBF, but they cannot deposit apatite on the open surface for up to 2 months of staking. The implications of such apatite deposition behavior have been discussed in relation to the environments of titanium implants in bone as well as to the methodology of the SBF staking experiment.

Hydroxyapatite-coated Ti-6Al-4V part 2: the effects of post-deposition heat treatment at low temperatures

Improvement of Bioactivity of H(2)O(2)/TaCl(5)-treated Titanium after Subsequent Heat Treatments.

A Comparative Study of in Vitro Apatite Deposition on Heat-, H2O2-, and NaOH-treated Titanium Surfaces

Effect of Heat Treatment on Characteristics of Plasma Sprayed Hydroxyapatite Coatings

Impact of post-heat-treatment on the surface-roughness, residual stresses, and micromorphology characteristics of plasma-sprayed pure hydroxyapatite and 7%-Aloxite reinforced hydroxyapatite coatings deposited on titanium alloy-based biomedical implants

Effect of Heat Treatment of Nano-Hydroxyapatite Coatings Prepared Using Electrohydrodynamic Deposition

Immersion Behavior of Plasma-Sprayed Modified Hydroxyapatite Coatings after Heat Treatment

In vitro characterization of postheat-treated plasma-sprayed hydroxyapatite coatings

Effect of hydrothermal treatment temperature on the hydroxyapatite coatings deposited by electrochemical method

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

Hydroxyapatite Coating with Strong (002) Crystallographic Texture Deposited by Micro-Plasma Spraying

Effects of Hydrogen Peroxide Concentration and Heat Treatment on the Mechanical Characteristics and Corrosion Resistance of Hydroxyapatite Coatings

Effect of post-deposition heat treatment on microstructure and mechanical properties of NASA HR-1 cold spray coatings

Effects of heat treatment on hydriding/dehydriding characteristics of Ti18Cr24V55Zr3 alloy

Effects of heat treatments on the microstructure and hardness of thermally sprayed Ni-Cr-Mo-Al alloy coating

Characterization of Hydroxyapatite and Titanium Coatings Sputtered on Ti-6Al-4V Substrate.

Hydrothermal treatment of Ti surface to enhance the formation of low crystalline hydroxyl carbonate apatite

MICROSTRUCTURAL HEALING WITH INTERFACIAL REACTION LAYERS ON THE ADHESIVE STRENGTH ENHANCEMENT OF PLASMA-SPRAYED HYDROXYAPATITE COATINGS

Effects of different heat treatments on anisotropy of cold sprayed 7075 Al deposits

In Vitro Evaluation of Biologically Derived Hydroxyapatite Coatings Manufactured by High Velocity Suspension Spraying

Effect of Heat Treatment on the Mechanical and Tribological Properties of Dual-Reinforced Cold-Sprayed Al Coatings