Abstract:As one of the typical nanostructures, nanotwins (NTs) have been utilized to evade the trade-off between strength and ductility, which is also applicable to improve the mechanical properties of superalloys. However, the optimization capability of mechanical properties by tailoring NTs has encountered bottleneck for the reasons such as inverse Hall-Petch effect and anisotropic effect. Based on the experimental observation of a special distribution pattern of NTs and nano-precipitates (NPs) in superalloys, that is, NPs are located at the twin boundaries (TBs), our work aims to study the distinctive synergistic deformation mechanism between NTs and NPs, which could become a new microstructure design strategy to optimize the mechanical properties of superalloys. Specifically, molecular dynamic (MD) method was employed to unveil the synergistic deformation mechanism of NTs and NPs in a model Ni-based superalloy. As expected, the introduction of NPs onto TBs can inhibit dislocation motion along or parallel to TBs, despite the softening deformation mode of NTs is activated. Moreover, the existence of NPs onto TBs can greatly improve the strengthening efficiency of NTs by impeding twin thickening/thinning. On the other hand, both phase boundaries and NPs interior have obstructive effect on dislocation motion, which could also be beneficial for material strengthening. More interestingly, anti-phase boundary (APB) structure will form along with the dislocations cutting through NPs. Subsequently, the APB structure can act as channels for dislocation slip and dislocation nucleation site induced by a kind of TB confinement effect, which may effectively accommodate plastic deformation. Our research outcomes could be utilized to facilitate the development of high-performance superalloys via rational collaborative design of NTs and NPs.

Tailoring the nanotwin spacing of Ni-Mo-W alloys via composition and substrate temperature control

A Molecular Dynamics Study on Mechanical Performance and Deformation Mechanisms in Nanotwinned NiCo-based Alloys with Nano-Precipitates under High Temperatures

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Nanotwin formation in Ni–Mo–W alloys deposited by dc magnetron sputtering

Atomistic insights into the synergistic effect of nanotwins and nano-precipitates on the mechanical behavior of superalloys

Anisotropic Mechanical Properties and Deformation Mechanisms of Nanotwinned Ni and Ni Alloys With Extremely Fine Twin Boundary Spacings

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

In Situ Study of the Microstructural Evolution of Nickel-Based Superalloys with High Proportional Twin Boundaries Obtained by High-Temperature Annealing

Tailoring Nanostructured Ni-Nb Metallic Glassy Thin Films by Substrate Temperature

Enhancing Strength and Ductility of a Ni-26.6Co-18.4Cr-4.1Mo-2.3Al-0.3Ti-5.4Nb Alloy via Nanosized Precipitations, Stacking Faults, and Nanotwins

Effect of γ' phase and microtwins on the microstructural evolution and mechanical properties of a novel Ni–Co base superalloy

Overcoming high-temperature strength-ductility trade-off by combination deformation twinning of C11b and D022 superlattices in a Ni-Cr-W/Mo-based superalloy

Tuning Mo/W ratio to improve high temperature oxidation resistance of single crystal nickel base superalloys

Effect of twin spacing and loading mode on mechanical properties and deformation mechanism of NiCoAl columnar polycrystalline alloy

Suppression of twinning mechanism on nanoscale: size effect in Cu–Ni–Al shape memory alloy

Fabrication of low thermal expansion Fe–Ni alloys by in-situ alloying using twin-wire arc additive manufacturing

Structural Change of Ni–Cu Alloy Nanowires with Temperature Studied by in Situ X-ray Absorption Fine Structure Technique

Individual Layer Thickness Dependence of Microstructure and Mechanical Properties of Magnetron Sputtering Mo-W-Doped Ni/Ni3Al Multilayers

Mechanical Behaviors of Chromium- or Niobium-Modified Ni47.5Al25Fe27.5 Alloy at Elevated Temperature