Abstract:Developing hard carbon with a high initial Coulombic efficiency (ICE) and very good cycling stability is of great importance for practical sodium-ion batteries (SIBs). Defects and oxygen-containing groups grown along either the carbon edges or the layers, however, are inevitable in hard carbon and can cause a tremendous density of irreversible Na+ sites, decreasing the efficiency and therefore causing failure of the battery. Thus, eliminating these unexpected defect structures is significant for enhancing the battery performance. Herein, we develop a strategy of applying a soft-carbon coating onto free-standing hard-carbon electrodes, which greatly hinders the formation of defects and oxygen-containing groups on hard carbon. The electrochemical results show that the soft-carbon-coated, free-standing hard-carbon electrodes can achieve an ultrahigh ICE of 94.1% and long cycling performance (99% capacity retention after 100 cycles at a current density of 20 mA g–1), demonstrating their great potential in practical sodium storage systems. The sodium storage mechanism was also investigated by operando Raman spectroscopy. Our sodium storage mechanism extends the "adsorption–intercalation–pore filling–deposition" model. We propose that the pore filling in the plateau area might be divided into two parts: (1) sodium could fill in the pores near the inner wall of the carbon layer; (2) when the sodium in the inner wall pores is close to saturation, the sodium could be further deposited onto the existing sodium.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12171.Digital picture of the material sandwiched between graphite boards, and SEM image of the carbon paper; digital photograph of large size carbon paper; comparison of XRD, Raman, and infrared spectra of soft carbon; rate performance of HC-P-1200; Nyquist plots of HC-P-1200 and HC-W-1200; full information on operando Raman spectra of the charge–discharge process; periodic variation of the intensity of the charge–discharge for the first cycle, and slope of the second cycle at 1000 and 2000 cm–1 Raman shift (PDF)This article has not yet been cited by other publications.

Surface engineering based on in situ electro-polymerization to boost the initial Coulombic efficiency of hard carbon anode for sodium-ion battery

Biomass‐Derived Phosphorus‐Doped Porous Hard Carbon Anode for Stable and High‐Rate Sodium Ion Batteries

Molecular Engineering Enabling High Initial Coulombic Efficiency and Rubost Solid Electrolyte Interphase for Hard Carbon in Sodium‐Ion Batteries

Ameliorating the Sodium Storage Performance of Hard Carbon Anode Through Rational Modulation of Binder

Engineering Ultrathin Carbon Layer on Porous Hard Carbon Boosts Sodium Storage with High Initial Coulombic Efficiency.

Engineering Al2O3 Atomic Layer Deposition: Enhanced Hard Carbon-Electrolyte Interface Towards Practical Sodium Ion Batteries

Boosting the Reversible, High‐Rate Na + Storage Capability of the Hard Carbon Anode Via the Synergistic Structural Tailoring and Controlled Presodiation

Nitrogen/Phosphorus Dual‐Doped Hard Carbon Anode with High Initial Coulombic Efficiency for Superior Sodium Storage

Innovative discontinuous-SEI constructed in ether-based electrolyte to maximize the capacity of hard carbon anode

Engineering surface oxygenated functionalities on commercial hard carbon toward superior sodium storage

Boosting Sodium Storage Performance of Hard Carbon Anodes by Pore Architecture Engineering

Tailoring Pseudo-Graphitic Domain by Molybdenum Modification to Boost Sodium Storage Capacity and Durability for Hard Carbon

Solid Electrolyte Interphase Composition Regulation via Coating AlF 3 for a High-Performance Hard Carbon Anode in Sodium-Ion Batteries

Engineering the Trap Effect of Residual Oxygen Atoms and Defects in Hard Carbon Anode Towards High Initial Coulombic Efficiency

A Bifuctional Presodiation Reagent for Hard Carbon Anodes Enhancing Performance of Sodium-Ion Batteries

Pyridinic N‐Dominated Hard Carbon with Accessible Carbonyl Groups Enabling 98% Initial Coulombic Efficiency for Sodium‐Ion Batteries

A cation‐driven enhanced functionalization solid electrolyte interface for hard carbon anodes in sodium‐ion batteries

Soft-Carbon-Coated, Free-Standing, Low-Defect, Hard-Carbon Anode To Achieve a 94% Initial Coulombic Efficiency for Sodium-Ion Batteries

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Sustainable Fabrication of a Practical Hard Carbon Anode for a Sodium-Ion Battery with Unprecedented Long Cycle Life

Hard Carbon Microsphere with Built-In Electron Transport Channels as a High-Performance Anode for Sodium-Ion Batteries