Abstract:The practical application of lithium-sulfur (Li-S) batteries is limited by the easy dissolution of polysulfides in the electrolyte, resulting in the lithium polysulfide (LPS) shuttle effect. Several two-dimensional (2D) materials with abundant active binding sites and high surface-to-volume ratios have been developed to prepare functional separators that suppress the diffusion of polysulfides. However, the influence of modified layer thickness on Li+ transport has not been considered. Herein, we synthesized individual and multilayered 2D Ti3C2Tx MXene nanosheets and used them to fabricate a series of Ti3C2Tx-PP modified separators. The separators had mass loadings ranging from 0.16 to 0.016 mg cm(-2), which is the lowest value reported for 2D materials to the best of our knowledge. The corresponding reductions in thickness ranged from 1.2 mu m to 100 nm. LPS shuttling was effectively suppressed, even at the lowest mass loading of 0.016 mg cm(-2). Suppression was due to the strong interaction between LPS intermediates and Ti atoms and hydroxyl functional groups on the separator surface. The lithium-ion diffusion coefficient increased with the reduction of Ti3C2Tx layers on the separator. Superior cycling stability and rate performance were attained when the separator with a Ti3C2Tx-PP mass loading of 0.016 mg cm(-2) was incorporated into a Li-S battery. Carbon nanotubes (CNTs) were introduced into the separators to further improve the electrical and Li+ ionic conductivity in the cross-plane direction of the 2D Ti3C2Tx layers. With the ultra-lightweight Ti3C2Tx/CNTs modified PP separator, the cell maintained a capacity of 640 mAh g(-1) after 200 cycles at 1 C with a capacity decay of only 0.079% per cycle. (C) 2019 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

V4C3TX MXene: First-principles computational and separator modification study on immobilization and catalytic conversion of polysulfide in Li-S batteries

Three-Dimensional Ordered Fevo4 Nanocatalyst-Modified Separator Enables Suppressed Polysulfides Shuttling and Boosted Redox Conversion in Li-S Batteries

Promoting Li2S Nucleation/Dissolution Kinetics via Multiple Active Sites over TiVCrMoC3Tx Interface

Immobilizing Polysulfides with MXene-Functionalized Separators for Stable Lithium-Sulfur Batteries

Few-layered V2C MXene derived 3D V3S4 nanocrystals functionalized carbon flakes boosting polysulfide adsorption and catalytic conversion towards Li-S batteries

Separator modified by a caterpillar-like composite with interconnected N-doped carbon nanotubes decorated Co-MnO heterointerface enabling robust polysulfide adsorption and catalytic conversion for Li-S batteries

Designing a Functional CNT+PB@MXene-Coated Separator for High-Capacity and Long-Life Lithium-Sulfur Batteries

Immobilization and Kinetic Acceleration of Lithium Polysulfides by Iodine-Doped MXene Nanosheets in Lithium–Sulfur Batteries

Carbon-coated Nitrogen, Vanadium Co-Doped MXene Interlayer for Enhanced Polysulfide Shuttling Inhibition in Lithium-Sulfur Batteries

Ultra-lightweight Ti3C2T MXene Modified Separator for Li–S Batteries: Thickness Regulation Enabled Polysulfide Inhibition and Lithium Ion Transportation

A Janus MXene/MOF separator for the all-in-one enhancement of lithium-sulfur batteries

Synergistic catalytic conversion and chemisorption of polysulfides from Fe/Fe 3 C/FeN 0.0324 nanocubes modified separator for advanced Li-S batteries

Porosity Engineering of MXene Membrane towards Polysulfide Inhibition and Fast Lithium Ion Transportation for Lithium–Sulfur Batteries

Self-support interlayer of dual-intercalation MXene for accelerating polysufides conversion in lithium-sulfur batteries

Blocking polysulfide by physical confinement and catalytic conversion of SiO2@MXene for Li–S battery

Multifunctional Ultrathin Ti3C2Tx MXene@CuCo2O4 /PE Separator for Ultra‐High‐Energy‐Density and Large‐Capacity Lithium‐Sulfur Pouch Cells

Atom-dominated relay catalysis of high-entropy MXene promotes cascade polysulfide conversion for lithium–sulfur batteries

Separator modification by Mo x C/N-doped graphene enabling polysulfide catalytic conversion for high-performance Li-S batteries

Enhancing Lithium-Sulfur Battery Performance through Electronic/Ionic Co-Conductive MWCNTs/LLTO Separator Modification

Construction of Co@N-CNTs grown on N-MoxC nanosheets for separator modification to enhance adsorption and catalytic conversion of polysulfides in Li-S batteries

In situ self-assembled NiS 2 nanoparticles on MXene nanosheets as multifunctional separators: regulating shuttling effect and boosting redox reaction kinetics of lithium polysulfides