Abstract:Chlorine is an essential element of chemical industries, and especially has paramount importance in polymer industry. A typical route for chlorine generation is electrolysis of brine solution where chlorine is generated at the anode; producing caustic soda and hydrogen at cathode. However, the relevant state of the art membrane reactors is one of the most energy intensive processes in industry. Moreover, the membrane technology is believed to have reached the theoretical limit, and energy consumption cannot be reduced further. In the present chlor-alkali technology, sodium chloride solution is electrolyzed at a constant current density, and the decomposition voltage ΔE of the overall reaction is 2.186 V as per thermodynamic calculation. If the hydrogen evolution reaction at the cathode side is replaced with oxygen reduction reaction (ORR), the decomposition voltage will be significantly reduced, and, as a consequence, the energy consumption will be reduced simultaneously. Introduction of such oxygen depolarized cathode results in the following chemical reactions: Anode: 2Cl- —— Cl2+2e- (E=1.358 V vs. NHE) Cathode: 4Na+ + 2H2O + O2 +4e- —— 4NaOH (E=0.401 V vs. NHE) Overall Reaction: 4NaCl + 2H2O + O2 —— 4NaOH + 2Cl2 (ΔE=-0.957 V) Even though the voltage requirement can be minimized by oxygen depolarized cathode, there is still significant overpotential loss from the cathodic reaction. This is due to the fact that ORR is kinetically a very sluggish reaction. Platinum is the best catalyst known for ORR in acid media. However, Pt is poisoned in concentrated NaOH solution resulting in significant shifts in onset potential and limiting current values. Early in 1970s, heating of non-noble metal along with carbon and a source of nitrogen atoms in presence of ammonia resulted in formation of electrocatalysts with ability to reduce oxygen. Since then, there has been a gradual development of such “non-PGM” catalysts, where PGM stands for Precious Group Metals. The introduction of metal organic frameworks (MOFs) as sacrificial templates has brought a revolution in electrocatalysis research. Owing to the large surface area, preferable porosity and high nitrogen content, the non-PGM catalysts obtained from MOF precursors have shown excellent ORR activity. However, most of the MOF synthesis methods are based on the traditional solution reactions, which need either excessive amount of ligand or a huge amount of solvent, or both. Thus, the low yielding synthesis route and comprehensive separation methods of MOF seriously constrain the application of the MOF based catalysts for ORR. In the presentation, we will be discussing about the new in-house synthesized MOF based catalyst using solid-state reaction. In addition to advantages like simple preparatory route and high reproducibility, this catalyst has high yield and scalability which are uncommon traits for the more conventional MOF based catalysts. This catalyst has high ORR onset potential even in extreme corrosive conditions such as concentrated alkali and acid. Herein, we propose a facile, simplified approach to obtain the MOF based catalysts for ORR with low cost and high reproducibility. The as-prepared catalysts have been tested as oxygen depolarized cathodes in chlor-alkali electrolysis cells and have been operated at significantly lower voltages compared to commercial catalysts like Pt/C and Ag/C. References [1]. Eric Proietti. Nature Communications. 2011. 2, 461. [2]. Juan Tian. Angewandthe Chemie. 2013. 52, 6867. [3]. Aude Demessence. J. Mater. Chem. 2010. 20, 7676.

Investigation on the application of platinum anode towards direct electrochemical reduction of solid metal oxides in CaCl2–CaO melt

Overpotential on Oxygen-Evolving Platinum and Ni-Fe-Cu Anode for Low-Temperature Molten Fluoride Electrolytes

Engineering Porosity into Trimetallic PtPdNi Nanospheres for Enhanced Electrocatalytic Oxygen Reduction Activity

Investigation of the Electrochemical Reduction of Porous CaTiO 3 Pellets in CaCl 2 -0.5%CaO Molten Salt

Advanced Platinum Alloy Electrocatalysts for the Oxygen Reduction Reaction

Anodic and Cathodic Reactions in Molten Calcium Chloride

Non-Noble Metal Catalysts As Oxygen Depolarized Cathodes in Chlor Alkali Electrolyzers

Molten salt applications in materials processing

Proving the Availability of Ni-Fe Anode for Electro-Reduction of Solid V2O3 in Molten Fluoride Salts

The Catalytic Performance and Characterization of Nanoporous Gold Loading Platinum and Antimony (Oxidized) Catalysts Towards Cathode Oxygen Reduction Reaction

Characterisation of Electrochemical Properties for Molten Titanium(IV) Oxide - Sodium Oxide and Expansion into Other Binary Oxide Systems for the Electrolytic Reduction of Valuable Metals

Oxidation reactions in chromium(III) formate electrolytes at platinum and at a catalytic mixed metal oxide coating of iridium oxide and tantalum oxide

One−Step Synthesis Strategy for a Platinum−Based Alloy Catalyst Designed via Crystal−Structure Prediction

Acid Anion Electrolyte Effects on Platinum for Oxygen and Hydrogen Electrocatalysis

Investigating the platinum electrode surface during Kolbe electrolysis of acetic acid

Oxide Reduction Treatment with a Thermal Plasma Torch: A Case Study

(Invited) Alloy of Platinum with Rare Earth Metals for High Oxygen Reduction Reaction Activity and Durability

Mesostructured Intermetallic Compounds of Platinum and Non‐Transition Metals for Enhanced Electrocatalysis of Oxygen Reduction Reaction

Platinum-Modified Mixed Metal Oxide Electrodes for Efficient Chloralkaline-Based Energy Storage

Molten‐Salt Electrochemical Deoxidation Synthesis of Platinum‐Neodymium Nanoalloy Catalysts for Oxygen Reduction Reaction

Enhancement of Activity and Development of Low Pt Content Electrocatalysts for Oxygen Reduction Reaction in Acid Media