Abstract:Additive technologies make it possible to manufacture products using a layer-by-layer synthesis, thus obtaining products of complex shapes. When solving a complex problem of numerical modeling of additive technological processes, it is necessary to describe various thermomechanical phenomena with high accuracy. The most effective in this regard is the use of a combination of capabilities of specialized software systems and the development of unique algorithms for them, taking into account the maximum possible number of process parameters. The paper considers the calculation algorithm of non-stationary temperature fields and stress-strain state of the structure in the process of its creation by 3D welding of wire materials developed and implemented using the ANSYS Mechanical package in the APDL language. In particular, this model takes into account the non-stationary radiant transfer of thermal energy of the welding arc to the surface of the product. The review highlights three of the most commonly used methods for modeling material deposition, i.e. the so-called element birth, sleeping element (quiet element) and hybrid activation (hybrid activation). It is shown that in order to ensure greater efficiency of calculations, it is necessary to use the principle in which successive steps of melting and even layers are grouped together for a subsequent simultaneous activationn. In the presented model, the task is divided into the boundary problem of non-stationary thermal conductivity and the boundary problem of thermomechanics of the stress-strain state, which are uncoupled. To solve them we applied the technology of killing and the subsequent birthing of a part of the material, implemented with the ANSYS package. Verification of the developed numerical algorithm aimed at solving the three-dimensional problem of the arc surfacing of wire materials was carried out by a comparison with the results of the experimental tests on D16 aluminum alloy samples. To describe the elastoplastic behavior of the alloy, the BISO model of bilinear isotropic plasticity with a temperature dependence of yield strength was used. A good consistency of the calculated data with the experiment was shown. The effect was studied on the level of the residual distortion of such process parameters as exposure time to the next layer, the motion path of the slicer, ambient temperatures. It is shown that the latter parameter is the most effective way to reduce residual shape deviations, but requires high thermal stability of equipment and accuracy of arc energy control.

INTERLAYER EFFECT ON DEFORMATION AND FRACTURE OF DENDRITIC STRUCTURE FORMED DURING WIRE-FEED ELECTRON-BEAM ADDITIVE MANUFACTURING OF AL-SI ALLOY

STUDYING OF THE INFLUENCE OF 3D WIRE DEPOSITION PROCESS PARAMETERS ON THE FORMATION OF RESIDUAL DEFORMATIONS

Effects of Local Strain on the Plastic Deformation and Fracture Mechanism of Heterogeneous Multilayered Aluminum

Studying the layer structure formation in laser additive manufacturing with AlMg6 alloy wire

Interfacial-constraint-induced Intragranular Deformation Inhomogeneity of Ti−Al Layered Composites

Modelling and Experimental Observation of the Deposition Geometry and Microstructure Evolution of Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Deformation Behavior of Brittle/ductile Multilayered Composites under Interface Constraint Effect

Microstructure and Solute Concentration Analysis of Epitaxial Growth During Wire and Arc Additive Manufacturing of Aluminum Alloy

The Influence of Layer Thickness on the Deformation and Fracture of Layered Metals: Insights from Synchrotron Laue Microdiffraction and Mechanistic Model

Effects of Interlayer Temperature on the Microstructures of Wire Arc Additive Manufactured Al-Zn-Mg-Cu Alloy: Insights into Texture Responses and Dynamic Precipitation Behaviors

Deformation Mechanisms Dominated by Decomposition of an Interfacial Misfit Dislocation Network in Ni/Ni3Al Multilayer Structures

Influence of cellular dendritic structure and grain orientation on deformation behavior of additively manufactured AlSi10Mg alloy

Influence of the Coarse Grain Structure of a Titanium Alloy Ti-4Al-3V Formed by Wire-Feed Electron Beam Additive Manufacturing on Strain Inhomogeneities and Fracture

Dislocation-based mechanical responses and deformation mechanisms of Al/Cu heterointerfaces: A computational study via molecular dynamics simulations

The influence mechanism of periodic heterogeneous distribution of microstructure on fracture behavior in the 2319 aluminum alloy of wire-arc directed energy deposition

Interface Formation and Deformation Behaviors of an Additively Manufactured Nickel-Aluminum-bronze/15-5 PH Multimaterial Via Laser-Powder Directed Energy Deposition

Effect of Interlayer Cooling Time, Constraint and Tool Path Strategy on Deformation of Large Components Made by Laser Metal Deposition with Wire

Effects of Deposition Paramaters on the Microstructure Evolution of Wire Arc Additive Manufactured Al–Zn–Mg–Cu Alloy

Coupled Study on In-Situ Synchrotron High-Energy X-ray Diffraction and In-Situ EBSD on the Interfacial Stress Gradient in Layered Metals

The Effect of Layer Interface on Recrystallization Behavior of Layered Aluminum: an In-Situ EBSD Study

Molecular dynamics studies of the effect of intermediate Fe layer thickness on the enhanced strength and ductility of Cu/Fe/Ni multilayer