Abstract:Effects of varied levels of cerium (28 × 10–6, 65 × 10–6 and 150 × 10–6) on inclusions in a high-carbon chromium bearing steel at different stages (before adding cerium, after adding cerium for 1, 5, 10 min and ingot) were studied using laboratory experiments. An automatic scanning electron microscope system with energy-dispersive spectroscopy was used to analyze the amount, composition, size and morphology of inclusions in the steel at different stages. When the cerium content in the molten steel increased from 0 to 150 × 10–6, the evolution sequence of inclusions was as follows: Al2O3 → CeAl11O18 → CeAlO3 → Ce2O2S. After 28 × 10–6 cerium was added, Al2O3 inclusions were modified into CeAl11O18 inclusions in the molten steel and then were further transformed into Al2O3 and CeAlO3 inclusions in the solid steel during cooling. With the addition of 65 × 10–6 cerium, inclusions in the molten steel were modified into CeAlO3 and a small number of Ce2O2S inclusions. When the addition amount of cerium increased to 150 × 10–6, inclusions were transformed to Ce2O2S. The size of inclusions in the molten steel decreased obviously with cerium addition. On the other hand, the size of inclusions increased during the cooling process in solid steels of No. 1 steel (with 28 × 10–6 cerium) and No. 2 steel (with 65 × 10–6 cerium). During the cooling process, unmodified MnS inclusions were precipitated in the solid steel of No. 1 steel and wrapped outside the Al2O3 and CeAlO3 inclusions to form large complex inclusions. During the cooling process of No. 2 steel, the inclusion size of CeAlO3 increased due to the collision and polymerization. In the No. 3 steel (with 150 × 10–6 cerium), the average size of inclusions decreased rapidly and remained at a lower size during the cooling process, which was beneficial to improving the fatigue life of the steel.

Research on TiN inclusion modification in 20CrMnTi gear steel by rare earth Ce during Si-Ca-Ba-Ce composite deoxidation

Effects of rare earth Ce on TiN inclusion modifications in 20CrMnTi steel under deoxygenation conditions of Si–Ca–Ba alloy

Effects of Ce-Modified TiN Inclusions on the Fatigue Properties of Gear Steel 20CrMnTi

Study on the Influences of Adding Rare Earth Ce on the Precipitation Behaviors of TiN Inclusions in 20CrMnTi

Characteristics and Formation Mechanism of Complex TiN Inclusions in 20CrMnTi Gear Steel

Effect of Trace Magnesium Addition on TiN Inclusions and Microstructure in 20CrMnTi Gear Steel

On the grain coarsening behavior of 20CrMnTi gear steel during pseudo carburizing: A comparison of Nb-Ti-Mo versus Ti-Mo microalloyed steel

Research on the improvement and mechanism of La-Ce on inclusions in GCr15 bearing steel

A study of microstructure and property of Fe-B-C alloy modified by Ti-Ce-Mg

Cerium Addition Effect on Modification of Inclusions, Primary Carbides and Microstructure Refinement of H13 Die Steel

Effect of cerium addition on non-metallic inclusions in a high-carbon chromium bearing steel

Comparative tribological performance of a-C:H, ta-C and AlCrSiN coatings on 20CrMnTi gear steel under dry sliding condition

Optimization of Inclusion and Microstructure of As‐Cast Nonquenched and Tempered Steel F38MnVS with Trace Ce

Preparation of Ni-P-Ti3C2Tx-Ce composite coating with enhanced wear resistance and electrochemical corrosion behavior on the surface of low manganese steel

Effect of Ce Addition on Inclusions and Primary Carbide Network in AISI 440C Bearing Steel

Study of the relationship among total oxygen, inclusions and fatigue properties of gear steel

Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites

Effect of Cerium Content on the Evolution of Inclusions and Formation of Acicular Ferrite in Ti-Mg-Killed EH36 Steel

Study on modification of primary carbides and improvement of properties in H13 steel by CeO 2 nanoparticles addition

Friction-reducing and anti-wear performance of SiO 2 -Coated TiN nanoparticles in gear oil

The Effect of N Content on the Microstructure and Wear Resistance of Improved High-Carbon Chromium Bearing Steel