Abstract:High-voltage Li-ion batteries are anticipated to play a crucial role in the present transition towards electric vehicles, owing to their high energy density. However, a big challenge is the anodic stability (often referred to as corrosion) of the positive electrodes current collector, aluminum (Al), at potentials > 3.0 V vs . Li + /Li). In this work, we present a systematic study on the corrosion of 12 μm-thick Al foil (©Gränges, Sweden) up to 5.0 V vs . Li + /Li in a series of carbonate electrolytes containing lithium hexafluorophosphate (LiPF 6 ), lithium bis(fluorosulfonyl) imide (LiFSI) or lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) salts. The selection of the 12 μm foil was motivated by the need to decrease the mass or volume of the dead weight components (i.e., current collector) to increase the energy density of the battery. The electrochemical behavior was investigated using voltammetric techniques, and the results indicated that the anodic oxidation of the 12 μm Al foil was similar to that of the conventionally used 20 μm-thick Al foil. Notably, the first anodic oxidation scan exhibited a two-step oxidation after 3.5 V vs. Li + /Li, suggesting carbonate solvent oxidation and a liberation of H + ions attacking the native surface Al 2 O 3 layer followed by oxidation of metallic Al. A passivation was observed on the subsequent scans in 1.0 M LiPF 6 solutions due to formation of surface layer of AlF 3 , as confirmed by X-ray photoelectron spectroscopy (XPS) analyses. [1,2] However, in 1.0 M solutions of the imide salts (i.e., LiFSI or LiTFSI) a continuous anodic oxidation of aluminum was seen between 3.5 and 5.0 V vs. Li + /Li on the first few scans. After this the magnitude of the anodic current decreased significantly. The latter observations can be attributed to formation of soluble Al(TFSI) x or Al(FSI) x complexes [3] and a gradual saturation of the electrolyte. The voltammetric experiments showed that the magnitude of the anodic current increased when increasing the volume of the used imide electrolyte, supporting the saturation hypothesis. Results and analyses regarding the anodic oxidation of Al in a series of carbonate solvents and using different salt concentration, as well as effect of the use of carbon coated Al will also be presented. References: [1] S. T. Myung, Y. Sasaki, S. Sakurada, Y. K. Sun, H. Yashiro, Electrochim. Acta 2009 , 55 , 288. [2] C. Bizot, M.-A. Blin, P. Guichard, J. Hamon, V. Fernandez, P. Soudan, J. Gaubicher, P. Poizot, Electrochem. commun. 2021 , 126 , 107013. [3] M. Morita, T. Shibata, N. Yoshimoto, M. Ishikawa, J. Power Sources 2003 , 119 – 121 , 784.

Exploring the possibility of aluminum plating/stripping from a non‐corrosive Al(OTf)3‐based electrolyte

Impact of Surface Microstructure and Properties of Aluminum Electrodes on the Plating/Stripping Behavior of Aluminum-Based Batteries Using Imidazolium-Based Electrolyte

Modification of Al surface via acidic treatment and its impact on plating and stripping

Understanding The Reversible Electrodeposition of Al in Low-Cost Room Temperature Molten Salts

Aqueous Aluminum Cells: Mechanisms of Aluminum Anode Reactions and Role of the Artificial Solid Electrolyte Interphase

Revisiting the Anodic Stability of Aluminum Current Collectors in High-Voltage Li-Ion Batteries

Understanding the Initial Stages of Reversible Mg Deposition and Stripping in Inorganic Non-Aqueous Electrolytes

A Comprehensive Study on the Parameters Affecting Magnesium Plating/Stripping Kinetics in Rechargeable Mg Batteries

Properties and composition of the spent electrolyte for premium circulation mediated by Al-air batteries.

Reversible Al Metal Anodes Enabled by Amorphization for Aqueous Aluminum Batteries

A Bi-based artificial interphase to achieve ultra-long cycling life of Al-metal anode in non-aqueous electrolyte

Protective Al 2 O 3 Thin Film Coating by ALD to Enhance the Anodic Stability of Metallic Current Collectors in Ethereal Mg Electrolyte Solutions

Acetonitrile‐Based Electrolytes for Rechargeable Zinc Batteries

Aluminum Alloys as Anodes for Aluminum Batteries

Laminated Tin–Aluminum Anodes to Build Practical Aqueous Aluminum Batteries

Stable Aluminum Metal Anode Enabled by Dual-Functional Molybdenum Nanoparticles

Synergy of coordination and trace ionization from co-solvents enables reversible magnesium electroplating/stripping behavior

In Situ Analytical Techniques: Solid Electrolyte Interface Analysis of Al Anode Materials for Al-Ion Batteries

Modulating Aluminum Solvation with Ionic Liquids for Improved Aqueous-Based Aluminum-Ion Batteries

Electrode–Electrolyte Interactions in an Aqueous Aluminum–Carbon Rechargeable Battery System

Influence of Chloride and Electrolyte Stability on Anode Passivation Layer Formation and its Dissolution in Mg Batteries Revealed by operando EQCM-D