Abstract:Aiming at the problems of safety production cost caused by the increase of mining face width and pressure mining in Xizhuo Coal Mine in Chenghe Mining area, a mechanical model of floor plastic slip failure is established based on the theory of plastic slip line, and the difference between it and the traditional floor failure model is analyzed. The damaged contour line of the support stress and lateral support stress on the bottom plate through the advancing direction of the working face is the intersection line of a straight line and an arc line. The failure of the floor caused by lateral supporting stress is the failure of the floor again on the basis of the failure of the floor in the advancing direction of the working face, and there is a superimposed failure area. The analysis of the failure form of the stope floor by this mechanical model is closer to the engineering practice. By using "ultrasonic detection method + stress monitoring inverse analysis method," the measured data such as disturbance failure depth and distribution law of large mining width working face were obtained. The test method used in this paper is relatively rare in the monitoring of the depth of floor disturbance failure at home and abroad. Considering that the traditional pressure water test method has disadvantages such as easy collapse hole, long period, and large error in monitoring the failure rule of deep floor rock mass, the embedded stress monitoring and reverse analysis method and ultrasonic detection method are used to successfully collect and real‐time monitor the data of rock floor before, during and after mining in the lower part of wide mining face of Xizhuo Coal Mine for the first time, and several effective data are obtained, which solves the three‐part "spatial‐time" all‐round floor disturbance and failure law field measurement which cannot be realized by traditional testing technology. By comparing the results of theoretical analysis, field measurement, and numerical simulation, the law and depth of floor disturbance failure of a 240‐m wide mining face in the Chenghe mining area are obtained for the first time, which provides scientific guidance for floor water disaster induced by coal seam mining under similar conditions in the future and has an important reference role for the prevention and control of Ordovician ash water disaster in coal mining. It provides important technical parameters for the safe setting of the effective water barrier layer and the selection and timing of the grouting layer of the floor, which can bring considerable economic and social benefits. The research results have important popularization value.

Floor stability in the first layer of mine workings when the stope is run through an impact zone of a geological fault

Failure characteristics induced by unloading disturbance and corresponding mechanical mechanism of the coal-seam floor in deep mining

Mining of rich iron ore deposits of complex structure under the conditions of rock pressure development

Detection and Theoretical Numerical Simulation of the Failure Depth of the Bottom Plate in Belt Pressure Mining

Evolution Characteristics of Overburden Instability and Failure under Deep Complex Mining Conditions

Methods of hydraulic fracturing of poorly caving roof and coal seams to eliminate dynamic phenomena in coal mines

Research on the required width of a fault waterproof coal pillar based on underground pressure control theory

Prevention Technology for Strong Mine Pressure Disaster in the Hard-Roof Large-Mining-Height Working Face

Microseismic energy distribution and impact risk analysis of complex heterogeneous spatial evolution of extra-thick layered strata

Study on the Dynamic Evolution of Mining-Induced Stress and Displacement in the Floor Coal-Rock Induced by Protective Layer Mining

Research on dynamic response characteristics of normal fault footwall working face and rock burst prevention technology under the influence of the gob area

Assessment of the state of the rock mass around the crosscuts under additional deformation disturbances

Fault quasi-static and dynamic ruptures in deep coal mining: impacts on working faces

Porosity zoning characteristics of fault floor under fluid-solid coupling

Floor Pressure-Relief During Top Slice Mining of Extra-Thick Coal Seams and Its Implications for Gas Drainage Application

Assessing the geomechanical state of the main working network state in the case of undermining in the conditions of weak rocks

Dynamic Mechanical Response and Movement Evolution Characteristics of Fault Systems in the Coal Mining Process

Mechanical Analysis of the Failure Characteristics of Stope Floor Induced by Mining and Confined Aquifer

Study on overlying strata movement patterns and mechanisms in super-large mining height stopes

Failure characteristics of overlying strata and mechanism of strong ground pressure during the large‐scale and continuous mining of deep multi working faces

Damage Characteristics Caused by Deep-Hole Blasting near Normal Fault and Its Effects on Coal and Gas Outbursts