Abstract:The noise generated by the metal air turbine handpiece employed in dental practice is considerable and attended with predominant high frequency components. Therefore, investigation of the noise generation mechanism and development of a silent air turbine handpiece was only a matter of course. In addition, the metal air turbine hardpiece is comparatively heavy and its production cost is high. From this point of view as well, production of a light air turbine handpiece at low cost is also desirable. In order to overcome the objections to the metal air turbine handpiece, appropriate plastics materials were employed wherever possible. In this study, the number of revolutions, noise level, frequency analysis, start pressure and weight of newly produced plastics handpieces and metal handpieces were examined and compared. The following results were obtained: 1. The number of revolutions of single-nozzle type air turbine handpieces encased in plastics housings and fitted with metal turbine rotors was higher than that of all-metal air turbine handpieces. The noise level of the former tended to be lower. 2. The number of revolutions of multi-nozzle type air turbine handpieces encased in plastics housings and fitted with turbine rotors with plastics turbine blades was almost equal to that of similar metal handpieces, with the noise level tending to be lower. 3. In the case of handpieces fitted with turbine rotors with dynamic balance, the number of revolutions was high and the noise level was low. This indicated that dynamic balance was a factor affecting the number of revolutions and noise level. 4. Narrow band sound frequency analysis of single-nozzle type air turbine handpieces showed a sharp peak at the fundamental frequency which was the same as the number of revolutions multiplied by the number of rotor turbine blades. It is thought that the noise from air turbine handpieces was aerodynamic in origin, being generated by the periodical interruption of steady air flow by rotor turbine blades. 5. The start pressure of plastics handpieces was almost equal to that of metal handpieces. 6. The weight of plastics handpieces was 20%-50% of that of metal handpieces. The present results indicate that it is possible to produce a new type of light, silent and aesthetical air turbine handpiece.

Torque, power and efficiency characterization of dental air turbine handpieces

Comparison between Electric Micromotors and Air Turbines relative to Technical Characteristics, Advantages and Disadvantages / Comparação entre Micromotores Elétricos e Turbinas de Ar em relação às Características Técnicas, Vantagens e Desvantagens

Synthetic optimization of air turbine for dental handpieces

The Air-Driven Dental Unit: Form and Function at a Mechanical Level

[Development of new type plastics air turbine handpiece for dental use]

Methodology for Counter Torque, Power Loss, and Frictional Heat for Brush Seals Under Eccentric Transients

Comparative Study Of Electric Handpiece And Air-Turbine Handpieces After Tooth Prepare For Veneer

Torque Generation of the Endodontic Instruments: A Narrative Review

A Study on Ways to Expand the Speed Operation Range of Dental Laboratory Handpiece Motors Using Low-Cost Hall Sensors

Research on aerodynamic characteristics of two-stage axial micro air turbine spindle for small parts machining

A selected literature review of efficiency improvements in hydraulic turbines

Numerical Investigation of Guide Vane Hydraulic Torque Characteristics of a Pump Turbine in Pump Mode

Thermodynamic analysis of the rotary tooth compressor

Effect of the Spray Pattern, Water Flow Rate, and Cutting Position on the Cutting Efficiency of High-Speed Dental Handpieces

Theoretical and Experimental Investigation on Tip Forces and Temperature Distributions of the Brush Seal Coupled Aerodynamic Force

Research on the Relationships Between Blade Angles and External Characteristics of A Centimeter Scale Pneumatic Turbine

Torque Characteristics in a Large Permanent Magnet Synchronous Generator with Stator Radial Ventilating Air Ducts.

Torque Characteristics Comparison And Analysis Of Surface-Mounted Permanent Magnet Vernier Machines With Different Stator Topologies

Design Methodology and Performance Analysis of Conical Rotors for Dry Screw Vacuum Pumps

Fluid dynamic analysis and design strategies for a deswirler device for the direct measurement of radial turbine isentropic efficiency in experimental test rig

A Methodological Approach for Motor Selection in Dental Impression Material Dispensers Using Experimental and Image Analysis Techniques