Abstract:This research examines the potential of a synthetic e-diesel and oxymethylene dimethyl ether blend in a heavy-duty single-cylinder engine. The main purpose is to find the optimal engine settings that maximize engine efficiency and minimize emissions. As the first step, a methodology was developed and applied to simplify the engine's map into five characteristic points to be representative of the World Harmonized Transient Cycle, assigning weights to each load region. This simplification reported low error estimations for fuel consumption and NOx emissions over the cycle. After obtaining the five points, a drop-in analysis was assessed, where the fuel was evaluated with the same settings as diesel, revealing more advanced and shorter combustion with great reductions in soot emissions. Then, a group of three air management and three injection parameters was selected for optimization. A novel methodology combining Taguchi Design and Response Surface Methodology is developed and applied to find the best engine settings. By integrating these two methods, the research reduced the number of required experiments if only one method were used and maintained the goal of achieving higher thermal efficiencies with the new fuel blend compared to the diesel baseline. Significant statistical results were obtained in the Taguchi design, revealing the air management factors that most affected the responses; meanwhile, second-order models with high accuracy helped in finding the best injection parameters. Subsequently, the best settings were experimentally evaluated, and optimal conditions determined by the two methods were validated, confirming the effectiveness of the methodology. Optimization results revealed an improvement of around 2% higher efficiencies for the five tested points while achieving important average reductions of 28% less in NOx with additional decreases in CO, HC, and soot levels, all outperforming traditional diesel benchmarks. Finally, a well-to-wheel analysis using the simplified cycle confirmed a substantial reduction in carbon impact when replacing diesel with this alternative fuel. The successful application of this methodology to recalibrate an engine with an alternative fuel blend shows the potential of using these fuels in existing engines and offers a novel methodology that can be escalated and applied under the engine calibration context.

Optimizing diesel engines with oxyhydrogen dual fuel: Enhancing performance with green methyl ester using MCDM techniques

Effect of oxyhydrogen as on energy, exergy and sustainability analysis of a diesel engine fueled with palm oil biodiesel

Parametric Optimization of Engine Performance and Emissions for Hydroxy Blended Gaseous Fuels

Experimental Analysis of Hydrogen Addition at Varying Injection Opening Pressures on a Dual-Fuel Diesel Engine Operating with Diesel and Cottonseed Oil

An Efficient Data-Driven Approach for Modeling and Optimization of Reactivity-Controlled Compression Ignition Engine Fueled with Polyoxymethylene Dimethyl Ethers and Hydrogen

Optimization methodology combining Taguchi design and response surface method to maximize a compression ignition engine efficiency fueled with oxygenated synthetic fuel

A comprehensive study on the performance and emission analysis in diesel engine via optimization of novel ternary fuel blends: Diesel, manganese, and diethyl ether

Performance optimization of a diesel engine fueled with hydrogen/biodiesel with water addition based on the response surface methodology

Performance-emission optimization in a single cylinder CI-engine with diesel hydrogen dual fuel: A spherical fuzzy MARCOS MCGDM based Type-3 fuzzy logic approach

The Influence of Diesel–Ethanol Fuel Blends on Performance Parameters and Exhaust Emissions: Experimental Investigation and Multi-Objective Optimization of a Diesel Engine

Analysis and Optimization of Operational and Pollutant Attributes of Diesel Engine with CNT-Infused Orange Peel Biodiesel-Diesel Blend Fuel

Use of 2-methoxyethyl ether and nitromethane as oxygenated additives for performance improvement and emission reduction of CI engine: experimental investigation and numerical simulation

A Taguchi-based hybrid multi-criteria decision-making approach for optimization of performance characteristics of diesel engine fuelled with blends of biodiesel-diesel and cerium oxide nano-additive

Numerical investigation on hydrogen-diesel dual-fuel engine improvements by oxygen enrichment

Optimization of biodiesel/2-propanol/1-hexanol blends based on diesel engine performance using combined mixture-process design (CMPD)

Experimental investigation and optimization of dual fuel combustion using diesel/gasoline and Bio-oil extracted from Co-thermal liquefaction of paint/biomass wastes: An approach towards waste to energy

Experimental Investigations on Efficiency and Instability of Combustion Process in a Diesel Engine Fueled with Ternary Blends of Hydrogen Peroxide Additive/biodiesel/diesel

Multi-objective RSM-based optimization of diesel-diethyl ether blends in diesel engine to achieve sustainable development goals

Performance augmentation and emission reduction in diesel engines using HfC-coated pistons with biodiesel blends

Enhancing diesel engine performance and emission reduction through hydrogen enrichment in algal biodiesel blends

Numerical study of hydrogen addition on the performance and emission characteristics of compressed natural gas spark-ignition engine using response surface methodology and multi-objective desirability approach