Failure criteria for brittle elastic materials

Z. Yosibash,A. Bussiba,I. Gilad

DOI: https://doi.org/10.1007/978-1-4614-1508-4_8

2004-02-01

Abstract:

What problem does this paper attempt to address?

Revisiting Failure of Brittle Materials

Y. W. Kwon

DOI: https://doi.org/10.1115/1.4050989

2021-05-31

Journal of Pressure Vessel Technology

Abstract:Abstract Failures of isotropic brittle materials were revisited to find out whether there are unified failure criteria, which can be applied to a load-carrying structural component made of a brittle material regardless of whether the component has a crack, a circular notch, or neither of these. To this end, a set of failure criteria were considered to determine failure of a local point which may be located at the crack tip, a notch tip, or any other location. The proposed criteria consist of two conditions, of which both must be satisfied for failure to occur. The first condition is that the local stress must not be lower than the failure strength of the material. The second condition is the stress-gradient condition. Even if the stress at a local point far exceeds the failure strength of the material, failure will not initiate until the stress gradient condition is satisfied. Four different examples cases were presented to explain the proposed failure concept.

engineering, mechanical
Failure Criteria for Brittle Notched Specimens

Y. W. Kwon,C. Diaz-Colon,S. Defisher

DOI: https://doi.org/10.1115/1.4053484

2022-02-14

Journal of Pressure Vessel Technology

Abstract:Abstract Recently, new failure criteria were proposed for brittle materials to predict their failure loads regardless of the shapes of a notch or a crack in the material. This paper is to further evaluate the failure criteria for different shapes of notches and different materials. A circular hole, elliptical hole, or crack-like slit with a different angle with respect to the loading direction were considered. Double circular holes were also studied. The materials studied were an isotropic material such as polymethyl methacrylate (PMMA) as well as laminated carbon fiber composites. Both cross-ply and quasi-isotropic layup orientations were examined. The lamination theory was used for the composite materials so that they can be modeled as an anisotropic and homogeneous material. The test results were compared to the theoretical predictions using the finite element analysis with two-dimensional plane stress models. Both theoretical failure stresses agreed well with the experimental data for the materials and notch geometries studied herein.

engineering, mechanical
A Teaching Note on Failure Criteria and Failure Surfaces for Ductile and Brittle Materials

G. S. Schajer

DOI: https://doi.org/10.1177/030641909402200101

1994-01-01

International Journal of Mechanical Engineering Education

Abstract:This note discusses some basic concepts underlying isotropic material failure criteria under multiaxial loadings. It also describes the shapes and features of the associated failure surfaces in three-dimensional stress space. Failure criteria for ductile materials are first reviewed. They are then generalized so that they may also be applied to brittle materials. The relationships among the various failure criteria, the shapes and characteristics of the associated failure surfaces, and the special features of physically acceptable isotropic failure criteria are then considered.
Brittle Fracture of an Elastic Layer with a Defect in the Form of a Circle under Biaxial Loading

Markin, A. A.

DOI: https://doi.org/10.1134/s0025654423601180

2024-06-05

Mechanics of Solids

Abstract:Based on experimental data on the combined loading of an infinite layer weakened by a circular hole in a brittle material, its critical state, determined by the energy criterion, is modeled. The failure criterion is related to the free energy flow through the interaction arc and the linear size. The proposed approach allows us to reflect the dependence of the critical external load on the radius of curvature. A procedure for determining the value of the linear size is proposed and implemented. Using known experimental results, an estimate of the introduced linear parameter for a layer of GVVS-16 gypsum was obtained.

mechanics
Hyperelastic effects in brittle materials failure

Markus J. Buehler,Farid F. Abraham,Huajian Gao

DOI: https://doi.org/10.1557/PROC-821-P6.3

2004-01-01

Abstract:A fact that has been neglected in most theories of brittle fracture is that the elasticity of a solid clearly depends on its state of deformation. Metals will weaken, or soften, and polymers stiffen as the strain approaches the state of materials failure. It is only for infinitesimal deformation that the elastic moduli can be considered constant and the elasticity of the solid linear. We show by large-scale atomistic simulations that hyperelasticity, the elasticity of large strains, can play a governing role in the dynamics of fracture and that linear theory is incapable of capturing all phenomena. We introduce a new concept of a characteristic length scale χ for the energy flux near the crack tip and demonstrate that the local hyperelastic wave speed governs the crack speed when the hyperelastic zone approaches this energy length scale. The new length scale χ, heretofore missing in the existing theories of dynamic fracture, helps to form a comprehensive picture of crack dynamics, explaining super-Rayleigh and supersonic fracture. We further address the stability of cracks, and show agreement of the Yoffe criterion with the dynamics of cracks in harmonic systems. We find that softening hyperelastic effects lead to a decrease in critical instability speed, and stiffening hyperelastic effects leads to an increase in critical speed. The main conclusion is that hyperelasticity plays a critical role in forming a complete picture of dynamic fracture.
Concept of Equivalent Stress Criterion For Predicting Failure of Brittle Materials

S. M. Sackey,T. Z. Ngewana

DOI: https://doi.org/10.26437/ajar.31.10.2022.23

2022-11-07

African Journal Of Applied Research

Abstract:Purpose: A paucity of proven failure criteria for brittle engineering materials exists, and this paper intends to present and validate a novel concept of equivalent stress criterion for predicting the failure of brittle isotropic homogeneous materials based on the concept of effective causative failure stress. Design/Methodology/Approach: Mathematical modelling is first performed based on strain-state equivalence, followed by conversion to the equivalent causative stress. The model is then validated with experimental and other data and with comparisons to traditional models. The material studied is BS 1452 Grade 250 continuous-cast grey cast iron with a Young’s Modulus of 39 000 MPa and ultimate tensile strength of 290 MPa. The test samples were prepared square in shape 12 mm x 12 mm to enable stresses in two perpendicular directions. Data is generated from uniaxial and bi-axial tests, performed using a standard universal testing machine, INSTRON 880, improvised to enable bi-axial recordings. Findings: Results point consistently to higher fidelity and transparency of the new model in representing the state of stress, especially in the second and fourth quadrants of the principal stress diagram, where Rankine’s criterion completely ignores stress differences and Mohr handles shear stresses in a suboptimal fashion. Both the maximum principal stresses and maximum shear stresses predicted by the proposed model are found to be somewhat greater than those from the traditional models, indicating higher accuracy and greater aggressiveness in prediction. The findings have further revealed that shearing effects play a greater role in the failure of engineering brittle materials than traditional failure theories have considered. Research Limitation: The study involved improvisation to enable biaxial stress recordings. This process was not perfect, resulting in smaller-than-ideal values of the lateral stresses. Practical implication: The study recommended process and equipment development toward perfecting multiaxial tests. Social implication: The survey will enrich the literature with pertinent design methodology to help in product design, including social-interest products. Originality / Value: Since truly homogeneous materials are known to withstand very high hydrostatic pressures, direct stresses alone do not constitute valid failure criteria for all loading conditions.
Cracking Behavior and Acoustic Emission Characteristics of Rock Containing a Single Preexisting Flaw

Xunjian Hu,Lina Luo,Gang Lei,Xiaonan Gong,Panpan Guo,Haibo Hu,Junjie Ma

DOI: https://doi.org/10.1155/2021/7117163

IF: 1.616

2021-01-01

Shock and Vibration

Abstract:The existence of flaws in brittle rocks or rock-like materials has an obvious influence on the material mechanical properties and cracking behavior of civil engineering projects. In this work, the two-dimensional particle flow code PFC2D was used to study the deformation and strength properties, failure processes, and acoustic emission (AE) characteristics of mudstone with a single preexisting flaw. First, the procedure to construct a parallel bond model is introduced. The Weibull distribution is used to reflect the mechanical heterogeneity of rocks. Then, the microscopic parameters used in PFC2D are calibrated to the macroproperties of mudstone obtained from laboratory tests under the uniaxial compression. The results indicate that the increases of the flaw inclination lead to the increasing uniaxial compressive strength and elastic modulus. In terms of microcrack evolution, the initiation, propagation, and coalescence of microcracks are closely related to the force chain. Specifically, an “X” shaped tension force chain concentrated area around the preexisting flaw is founded, which is the most prone area for microcracks to initiate. With an increase in flaw inclination, the b value of AE also shows an increasing trend. By incorporating the AE event numbers into a damage variable, this paper derives a constitutive model, which is verified by numerical results on brittle rocks with a single preexisting flaw under uniaxial compression.
Ab initio dynamics of rapid fracture

FF Abraham,D Brodbeck,WE Rudge,JQ Broughton,D Schneider,B Land,D Lifka,J Gerner,M Rosenkrantz,J Skovira,H Gao

DOI: https://doi.org/10.1088/0965-0393/6/5/010

IF: 2.421

1998-01-01

Modelling and Simulation in Materials Science and Engineering

Abstract:As our title implies, we consider materials failure at the fundamental level of atomic bond breaking and motion. Using computational molecular dynamics, scalable parallel computers and visualization, we are studying the failure of notched solids under tension using in excess of 10(8) atoms. In rapid brittle fracture, two of the most intriguing features are the roughening of a crack's surface with increasing speed and the terminal crack speed which is much less than the theoretical prediction. Our two-dimensional simulations show conclusively that a dynamic instability of the crack motion occurs as it approaches one-third of the surface sound speed. This discovery provides an explanation for the crack's surface roughening and limiting speed. For three-dimensional slabs, we find that an intrinsically ductile FCC crystal can experience brittle failure for certain crack orientations. A dynamic instability also occurs, but brittle failure is not maintained. The instability is immediately followed by a brittle-to-ductile transition and plasticity. Hyperelasticity, or the elasticity near failure, governs many of the failure processes observed in our simulations and its many roles are elucidated.
Hypocalcemic, hypophosphatemic rickets in rat pups suckling vitamin D-deprived mothers.

A. Boass,W. K. Ramp,S. Toverud

DOI: https://doi.org/10.1210/ENDO-109-2-505

IF: 5.051

1981-08-01

Endocrinology

Abstract:The effects of maternal vitamin D deprivation on rat pups were examined in terms of serum levels of Ca, phosphorus (P), and 25-hydroxyvitamin D (250HD), ash content, and histological appearance of long bones. In each of 10 experiments, litters of 8--10 young were examined at 2 or 3 different ages within the range of 5--57 days. Pregnant mothers were fed a diet containing 0.4% Ca, and 0.4% P and either no vitamin D(--D) or 5 IU D3/g diet (+D). Mothers fed the --D diet developed marked hypocalcemia (4--5 mg/dl) during lactation, but no change in milk Ca or P. The earliest changes in pups suckled by mothers on --D diets compared to pups suckled by mothers on +D diets were significant reductions at 8 days in serum P (6--12% in 3 of 5 experiments) and in serum 250HD3. By the 15th day, serum 250HD3 was undetectable, body weight was reduced by 26%, serum Ca was reduced by 9%, and serum P was reduced by 15%. During the following 10 days, when gradual weaning took place, serum Ca decreased progressively, serum P returned to normal, serum Mg became elevated, bone ash (as percent of dry weight of tibia) was decreased, and decalcified sections of the proximal end of the tibia revealed irregularity and widening (1.5- to 3-fold) of the hypertrophic cartilage layer and the metaphyseal trabeculae. All of these changes were also prominent in 8-week-old --D rats. The results indicate that rat pups suckling vitamin D-deprived mothers can develop biochemical evidence (including hypophosphatemia) as well as histological evidence of vitamin D deficiency similar to that of human vitamin D deficiency rickets. This is in contrast to rats deprived of vitamin D after weaning, who do not develop hypophosphatemia or characteristic histological evidence of rickets unless deprived of P as well as vitamin D.
Failure modes of complex materials with spatially-correlated mechanical properties -- the critical role of internal damage

Jerome Faillettaz,Dani Or

DOI: https://doi.org/10.48550/arXiv.1310.5948

2013-10-22

Adaptation and Self-Organizing Systems

Abstract:The study reports a systematic evaluation of the role of spatially correlated mechanical elements on failure behavior of heterogeneous materials represented by fiber bundle models (FBM) with different load redistribution rules. The increase of spatial correlation FBM for a local load sharing, results in a transition from ductile-like failure characteristics into brittle-like failure. The study identified a global failure criterion based on macroscopic properties (external load and cumulative damage) which is independent of spatial correlation or load redistribution rules. This invariant metric could be applied for early warning of a class of geophysical ruptures.
Failure criterion for highly stretchable elastomers under triaxial loading

Reza Pourmodheji,Shaoxing Qu,Honghui Yu

DOI: https://doi.org/10.1016/j.eml.2020.100645

IF: 4.728

2020-01-01

Extreme Mechanics Letters

Abstract:A failure criterion is introduced for highly stretchable hyper-elastic materials under tensile-dominated triaxial loading. It is based on energy balance using Griffith approach but is presented by the critical state of load as in traditional size independent strength theories. The basic argument is made of the recent assessment about the cavity nucleation in soft materials: the volumetric energy dissipation in the growth of defect and size-insensibility of the critical load in soft materials when the defect is smaller than the material characteristic length. Thus, using the energy approach as in fracture mechanics, we are able to estimate the critical state of load using only one material parameter, which is subsequently replaced by the critical stress under one specific loading, e.g., the strength of uniaxial loading. This leads us to the failure surface in the normalized principal stress space. The predictions of the present theory agree well with the experimental results collected from the literature, including an order of magnitude difference between the strengths of the uniaxial loading and hydrostatic loading. This addresses a variety of difficulties in the previous failure analyses. For the easiness of practical application, we further analyze the data and obtain a criterion using mean stress and the first invariant of Cauchy-Green deformation tensor, I-1. We are able to obtain the widely mentioned maximum I-1 criterion, and also find its limitation: only applicable when one of the principal stresses is zero. For general triaxial loadings, the material can fail at any allowable I-1 and the critical mean stress monotonically increases with I-1; and under a constant mean stress that is above the hydrostatic strength, the material is only safe when I-1 is above a mean stress-dependent lower bound but below an unknown up-bound. (C) 2020 Elsevier Ltd. All rights reserved.
Brittle fracture in a periodic structure with internal potential energy. Quasi-static analysis

Gennady S. Mishuris,Leonid I. Slepyan

DOI: https://doi.org/10.1098/rspa.2013.0821

2013-12-11

Abstract:We consider a linearly elastic body consisting of two equal symmetrically arranged layers (or half-planes) connected by a structured interface as a prospective crack path. The interface is comprised by periodic discrete system of bonds. In the initial state with no external forces, the bonds are assumed to be stressed in such a way that tensile and compressive forces of the same value alternate. In the general considerations, the layers are assumed to be of a general, unspecified {\em periodic} structure, where such self-equilibrated residual stresses can also exist. A two-line chain and an anisotropic lattice are examined as illustrative examples. We consider the states of the body-with-a-crack under the residual stresses and under a combined action of the remote forces and residual stresses. Analytical solutions to the considered problems are presented. The solutions are based on a selective discrete transform introduced. In particular, it is found that a formula for local-to-global energy release ratio, written in terms of the Wiener-Hopf equation kernel, is very general. We show that the residual stresses can manifest themselves in a number of phenomena such as the crack bridging, `porous' in front of the crack and crack growth irregularities. We also demonstrate analytically and graphically that the residual stresses can result in increase as well as in decrease of the crack resistance depending on the internal energy level. The quasi-static considerations suggest different scenarios of the crack growth depending on the internal energy level.

Classical Physics
General principles and criteria of failure of solids on different scale-structural levels under static and alternating loading

E. B. Zavoychinskaya

DOI: https://doi.org/10.26896/1028-6861-2022-88-7-48-62

2022-07-21

Abstract:Experimental and theoretical studies of the fracture regularities under monotonic and alternating loadings, including stress-corrosion fracture, revealed the main scale-structural levels of the brittle fracture (formation of a strip structure, nucleation of microcracks, microstructurally short non-propagating cracks and short propagating cracks, merging of short cracks with a macrocrack nucleation) and viscous fracture (an evolution of dislocation in slip bands, cellular structure formation, nucleation of a pit relief with micropores, merging of pores with a formation of meso-shear bands and initiation of a viscous crack, growing of a viscous crack under inelastic deformation) of crystal bodies. A transition from one level to another is determined by changes in the fracture mechanisms and occurs with varying degrees of probability. The necessity of considering the destruction as a hierarchical random step-by-step process on all scale-structural levels is substantiated. The fracture of plastic materials is considered as the sum of independent or dependent events, namely the initiation and growing of brittle cracks and evolution of pores through various mechanisms. Attaining of the limit states is determined by the statistics of the distribution of inhomogeneities throughout the entire body volume. The results of physical studies (using electron microscopy, X-ray structural analysis, etc.) provide determination of the geometry and density of defects, dislocations, pores, cracks at different levels. Macrocharacteristics of static, long-term and fatigue strength are determined using methods of mechanical tests. The regularities of the fracture evolution of engineering structures are determined using methods of non-destructive testing (ultrasonic analysis, acoustic emission analysis, magnetic flaw detection, etc.). A brief analytical review of the main known physical approaches — dislocation and energy structural theories, dislocation continuous theories, dilaton-frustron models, stochastic physical theories, and phenomenological approaches, including continuum damage theory and fracture mechanics — is presented. The analysis of gained data leads to the necessity of describing fracture in the framework of stochastic multilevel models. We consider the approach according to which the probability of reaching limit sates at each level under arbitrary multiaxial loading is determined by linear functionals of the loading process, kernels of the functionals being random functions of time. For simple proportional loading, the theory of brittle fatigue scale-structural failure is presented.
Criticality in the approach to failure in amorphous solids

Jie Lin,Thomas Gueudré,Alberto Rosso,Matthieu Wyart

DOI: https://doi.org/10.1103/PhysRevLett.115.168001

2015-09-24

Abstract:Failure of amorphous solids is fundamental to various phenomena, including landslides and earthquakes. Recent experiments indicate that highly plastic regions form elongated structures that are especially apparent near the maximal shear stress $\Sigma_{\max}$ where failure occurs. This observation suggested that $\Sigma_{\max}$ acts as a critical point where the length scale of those structures diverges, possibly causing macroscopic transient shear bands. Here we argue instead that the entire solid phase ($\Sigma<\Sigma_{\max}$) is critical, that plasticity always involves system-spanning events, and that their magnitude diverges at $\Sigma_{\max}$ independently of the presence of shear bands. We relate the statistics and fractal properties of these rearrangements to an exponent $\theta$ that captures the stability of the material, which is observed to vary continuously with stress, and we confirm our predictions in elastoplastic models.

Soft Condensed Matter,Statistical Mechanics
Failure Criteria for Unidirectional Fiber Composites

Z. Hashin

DOI: https://doi.org/10.1115/1.3153664

1980-06-01

Journal of Applied Mechanics

Abstract:Three-dimensional failure criteria of unidirectional fiber composites are established in terms of quadratic stress polynomials which are expressed in terms of the transversely isotropic invariants of the applied average stress state. Four distinct failure modes—tensile and compressive fiber and matrix modes—are modeled separately, resulting in a piecewise smooth failure surface.
STUDY ON BRITTLENESS OF GEOMATERIALS

LIU En-long,SHEN Zhu-jiang

DOI: https://doi.org/10.3321/j.issn:1000-6915.2005.19.007

2005-01-01

Abstract:How to describe the brittle failure process for geomaterials is a challenging problem.Up to nowt,here is no harmony among different authors in definition,concept or measurement of brittleness.The concept of brittleness is discussed firstly.Then,a brittleness index describing the brittle change of geomaterials is proposed on the basis of the conclusion of the prior measurement of brittleness,and is verified to describe the brittle change very well.Finally,the binary medium model proposed recently by the authors is used to simulate the stress-strain characteristics of geomaterials under loading conditions;and it is found that the model can duplicate the transference of deformation mode from the strain softening under the low confining pressures to the strain hardening under the high confining pressures;and the brittleness index gradually reduces when the confining pressure is increased.
On Failure Modes and Strength Characterization of Brittle Disordered Materials under Uniaxial Compression and Tension

CA Tang,P Lin,HY Liu,ZZ Liang

DOI: https://doi.org/10.4028/www.scientific.net/kem.183-187.637

2000-01-01

Abstract:With a newly developed Material Failure Process Analysis code (MFPA(2D)), influence of hetero geneity on fracture processes and strength characterization of brittle disorder materials such as rock or concrete is numerically studied under uniaxial compression and tension conditions. It is found th at, due to the heterogeneity of the disordered material, relatively more diffused micro-fractures appear in the early stage of loading. Different from homogeneous materials such as glass, macro-crack nucleation starts well before the peak stress is reached and the crack propagation and coalescence can be traced, which can be taken as a precursory to predict the macro-fracture of the material. The presence of residual strength in the post-peak region and the resemblance in the stress-strain curves between tension and compression are significant results and are found to be dependent on the heterogeneity of the specimens. Examples showing the tentative applications of MFPA(2D) in modeling failure of composite materials and rock or civil engineering problem are also given in this paper.
Cracking Evolution and Failure Mechanism of Brittle Rocks Containing Pre-Existing Flaws under Compression-Dominating Stresses: Insight from Numerical Approach

Yong Niu,Zewen Chen,Shengqi Yang,Yunjin Hu,Bolong Liu,Caijun Shao,Yanhui Guo

DOI: https://doi.org/10.1016/j.tafmec.2024.104719

IF: 4.374

2024-01-01

Theoretical and Applied Fracture Mechanics

Abstract:Comprehending the cracking evolution and failure mechanism of flawed rocks under compression-dominating stresses is essential to evaluating the stability of rock engineering. In this work, a newly developed geometry constraint-based non-ordinary state-based peridynamic (GC-NOSBPD) theory that can eliminate the numerical oscillation is applied to predict the development of new cracks of flawed rocks under compression-dominating stresses. The failure of bonds between particles is judged by the bond-associated stress-based fracture criteria. The cracking evolution trajectories of semi-disc and disc specimens containing flaws are traced. The effects flaw inclination angle on the cracking trajectories are analyzed. The cracking evolution paths of rock-like specimens with two flaws under uniaxial and biaxial compression are molded. The effects of confining stress on the growth of new cracks are investigated. The confining stress restrains the propagation of tensile cracks, it is easy to promote the growth of shear cracks. The concentration and transfer effects of stress can plainly revel the failure mechanism of flawed rocks. The present numerical method is reasonable to predict the tensile shear failure modes of flawed specimens under compression-dominating stresses.
Stability and roughness of tensile cracks in disordered materials

E. Katzav,M. Adda-Bedia

DOI: https://doi.org/10.1103/PhysRevE.88.052402

2013-11-02

Abstract:We study the stability and roughness of propagating cracks in heterogeneous brittle two-dimensional elastic materials. We begin by deriving an equation of motion describing the dynamics of such a crack in the framework of Linear Elastic Fracture Mechanics, based on the Griffith criterion and the Principle of Local Symmetry. This result allows us to extend the stability analysis of Cotterell and Rice to disordered materials. In the stable regime we find stochastic crack paths. Using tools of statistical physics we obtain the power spectrum of these paths and their probability distribution function, and conclude they do not exhibit self-affinity. We show that a real-space fractal analysis of these paths can lead to the wrong conclusion that the paths are self-affine. To complete the picture, we unravel the systematic bias in such real-space methods, and thus contribute to the general discussion of reliability of self-affine measurements.

Disordered Systems and Neural Networks,Materials Science,Soft Condensed Matter,Statistical Mechanics,Pattern Formation and Solitons
Yield criteria for quasibrittle and frictional materials

Davide Bigoni,Andrea Piccolroaz

DOI: https://doi.org/10.48550/arXiv.1010.1823

2010-10-09

Abstract:A new yield/damage function is proposed for modelling the inelastic behaviour of a broad class of pressure-sensitive, frictional, ductile and brittle-cohesive materials. The yield function allows the possibility of describing a transition between the shape of a yield surface typical of a class of materials to that typical of another class of materals. This is a fundamental key to model the behaviour of materials which become cohesive during hardening (so that the shape of the yield surface evolves from that typical of a granular material to that typical of a dense material), or which decrease cohesion due to damage accumulation. The proposed yield function is shown to agree with a variety of experimental data relative to soil, concrete, rock, metallic and composite powders, metallic foams, porous metals, and polymers. The yield function represents a single, convex and smooth surface in stress space approaching as limit situations well-known criteria and the extreme limits of convexity in the deviatoric plane. The yield function is therefore a generalization of several criteria, including von Mises, Drucker-Prager, Tresca, modified Tresca, Coulomb-Mohr, modified Cam-clay, and --concerning the deviatoric section-- Rankine and Ottosen. Convexity of the function is proved by developing two general propositions relating convexity of the yield surface to convexity of the corresponding function. These propositions are general and therefore may be employed to generate other convex yield functions.

Mathematical Physics

Failure criteria for brittle elastic materials

Revisiting Failure of Brittle Materials

Failure Criteria for Brittle Notched Specimens

A Teaching Note on Failure Criteria and Failure Surfaces for Ductile and Brittle Materials

Brittle Fracture of an Elastic Layer with a Defect in the Form of a Circle under Biaxial Loading

Hyperelastic effects in brittle materials failure

Concept of Equivalent Stress Criterion For Predicting Failure of Brittle Materials

Cracking Behavior and Acoustic Emission Characteristics of Rock Containing a Single Preexisting Flaw

Ab initio dynamics of rapid fracture

Hypocalcemic, hypophosphatemic rickets in rat pups suckling vitamin D-deprived mothers.

Failure modes of complex materials with spatially-correlated mechanical properties -- the critical role of internal damage

Failure criterion for highly stretchable elastomers under triaxial loading

Brittle fracture in a periodic structure with internal potential energy. Quasi-static analysis

General principles and criteria of failure of solids on different scale-structural levels under static and alternating loading

Criticality in the approach to failure in amorphous solids

Failure Criteria for Unidirectional Fiber Composites

STUDY ON BRITTLENESS OF GEOMATERIALS

On Failure Modes and Strength Characterization of Brittle Disordered Materials under Uniaxial Compression and Tension

Cracking Evolution and Failure Mechanism of Brittle Rocks Containing Pre-Existing Flaws under Compression-Dominating Stresses: Insight from Numerical Approach

Stability and roughness of tensile cracks in disordered materials

Yield criteria for quasibrittle and frictional materials