Abstract:Orientating the broccoli plays an important part in the trimming line, which helps reduce the redundant stalk length and provides accurate throughput data for sale. However, this work is still manual with high labor intensity and low work efficiency, and current grippers show limitations in replacing manual operations, which need the ability to self-adaptively grasp broccoli without damage and guide them upright. This study presented a novel pneumatic variable-curvature soft gripper (VCSG) for orientating broccoli, which mainly comprised three soft variable-curvature fiber-reinforced bending actuators (VCFRBAs). The VCFRBAs can generate additional lifting forces to help guide the broccoli upright, thus orientating the broccoli. A design concept was built for the VCFRBA, and an analytical model and finite element method (FEM) were proposed to evaluate the bending deformation of VCFRBA, achieving a good match with a root mean squared error of below 5.8 degrees. degrees . Step response tests of VCFRBA showed a response time of 0.35 s, hysteresis tests demonstrated a hysteresis error of less than 10 %, and durability tests in 5,000 cycles showed two error bands of both less than 5 %, indicating a fast response, good repeatability, and good durability, respectively. Single actuator force experiments demonstrated the VCFRBA can generate a clamping force of 1.13 N with an additional lifting force of 1.38 N when grasping under the pressure of 0.2 MPa. Furthermore, a maximum pull-off force of 35.06 N was measured for the VCSG at this pressure. Results of grasping experiments showed a 100 % success rate without damage when the VCSG grasped broccoli positioned upright, and broccoli can still be securely and self-adaptively grasped and guided upright when grasping them inclinedly. Further orientating tests suggested that the VCSG had a good performance with an 85 % success rate. These results demonstrate that the proposed VCSG has a good ability to orientate the broccoli self-adaptively without complex operations. This study showcases a novel VCSG, providing a unique solution to orientating broccoli in the trimming line.

Development and Experimental Validation of a 3D-Printed Force-Sensing Grabber for Automated Pineapple Harvesting

Design and development of a peduncle-holding end effector for robotic harvesting of mango

Design and Field Evaluation of a Robotic Apple Harvesting System with a 3D-Printed Soft-Robotic End-Effector

Design and performance evaluation of a novel end-effector with integrated gripper cum cutter for harvesting greenhouse produce

Prototype of a New Head Grabber for Robotic Strawberry Harvesting with a Vision System

Design and fabrication of a gripper propotype for a fruit harvesting machine

Fabrication of Pineapple Peeling Machine Using Pneumatic Solenoid Valve

Robotic Arm Gripper Using Force Sensor for Crop Picking Mechanism

Soft gripper for small fruits harvesting and pick and place operations

New design and construction of a mechanical gripping device with a telescopic link of a fruit harvesting robot

An Integrated Multi-Sensor Network for Adaptive Grasping of Fragile Fruits: Design and Feasibility Tests

Development of a Novel Variable-Curvature Soft Gripper Used for Orientating Broccoli in the Trimming Line

Structural design and analysis of an automatic pineapple picking and collecting straddle machine

Peduncle Gripping and Cutting Force for Strawberry Harvesting Robotic End-effector Design

Compact robotic gripper with tandem actuation for selective fruit harvesting

Design and Testing of Bionic-Feature-Based 3D-Printed Flexible End-Effectors for Picking Horn Peppers

Design and Evaluation of a Novel Cable-Driven Gripper with Perception Capabilities for Strawberry Picking Robots

An Autonomous Fruit and Vegetable Harvester with a Low-Cost Gripper Using a 3D Sensor

Development of a Visuo-Tactile Sensor for Non-Destructive Peach Firmness and Contact Force Measurement Suitable for Robotic Arm Applications

Design of an End-effector with Application to Avocado Harvesting

Development and validation of a 3D-printed interfacial stress sensor for prosthetic applications