Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Experimental and numerical study of seismic behaviour of panels made of polystyrene core and light weight concrete with pre-tensioned cables in interaction with simple steel frame

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

Flexural-Shear Behavior of High-Strength Concrete Short Columns

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Experimental evaluation of cyclic behavior of precast concrete frame with steel shear wall

Numerical Analysis Study on Seismic Performance of Semi-Rigid Steel Frame Infilled with Prefabricated Composite Wall Panels

Cyclic Lateral Loading Behavior of Thin-Shell Precast Concrete Wall Panels

In-Plane Behaviour of a Reinforcement Concrete Frame with a Dry Stack Masonry Panel.

Experimental Study on Seismic Behavior of High Strength Steel Frames: Local Response

Experimental and Numerical Investigation of the Seismic Performance of RC Moment Resisting Frames

Experimental study on influence of proposed FRP-strengthening techniques on RC circular short columns considering different types of damage index

Experimental investigation of seismic response of precast concrete panels with castellated keys support pillar connections under in-plane cyclic loading

Experimental and numerical studies of prefabricated structures using CFST frame and composite wall

Bending Performance of Precast Ceramsite-Concrete-Insulated Sandwich Panel with Stainless Steel Shear Connectors

Cyclic performance of steel moment frames with prefabricated RC and ECC wall panels

Experiments and Numerical Simulations on the Seismic Performance of Steel-Frame Composite Wallboard Shear Walls

Numerical Study of Seismic Behavior of Light-Gauge Cold-Formed Steel Stud Walls

Mechanical behavior of sandwich panels with hybrid face sheets and embedded super-elastic SMA wires under quasi-static loading: An experimental investigation

Study on the gap width between the steel plate and concrete panels on behavior of the buckling‐restrained steel plate shear walls

Seismic behavior of steel frame infilled with wall-panels connected by sliding joint

Seismic Performance of the Pre-Fabricated Steel Frame Infilled with AAC Wall Panels and Their Joint Connection: Full-Scale Shaking Table Test