Abstract:Unlike many other surface treatment techniques, such as shot peening (SP), low plasticity burnishing (LPB), ultrasonic surface rolling process (USRP), ultrasonic nanocrystal surface modification (UNSM), laser shock peening (LSP) is a non-contact process. This means that LSP achieves surface modification without direct physical contact, thereby eliminating the risk of media contamination and undesired wear on the peening equipment. As a surface hardening technology, LSP tends to produce a hardened layer with a high gradient of residual stress (RS) in the near-surface, significantly enhancing wear resistance. The well-known wear theories applied for numerical prediction, whether Archard model or dissipated frictional-energy model, contain a multiplier for contact pressure and relative slip amplitude p·ds or shear stress and relative slip amplitude q·ds , respectively. These multipliers are sensitive to the mechanical properties near the surface. Additionally, the wear profile is governed not only by the wear effect but also by the deformation of materials. Therefore, to accurately evaluate the wear performance for surface-hardened materials, the influence of RS is hard to be overlooked. In this work, the finite element method (FEM) is utilised to construct a 3D numerical model, which ignores and considers RS, for both as-received and LSP-treated samples. Two distinct RS distributions induced by different scanning strategies (one- and five-time), are introduced in the finite element (FE) model. The numerical simulation results are then compared with the experimental data to verify the accuracy of the fretting wear model built in this study. On this basis, the impact of different RS distributions on fretting wear characteristics, including wear profile and volume, is extensively investigated. The findings reveal that higher amplitude RS can reduce the degree of fretting wear to a greater extent, highlighting the beneficial role of RS in enhancing wear resistance. Furthermore, the numerical models incorporating RS demonstrate superior predictive accuracy compared to those that omit RS. This naturally underscores the importance of integrating RS in numerical simulations of LSP and other surface-hardened materials.

Effect of shot peening pressure on fretting wear properties of 42CrMoA steel

The influence of shot peening on mechanical properties, wear, and corrosion resistance of 42CrMo steel

Effect of shot peening on the surface integrity and fatigue property of gear steel 16Cr3NiWMoVNbE at room temperature

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

Effect of Shot Peening on the Surface Properties and Wear Behavior of Heavy-Duty-axle Gear Steels

Effects of Shot Peening Pressure, Time, and Material on the Properties of Carburized Steel Shafts

Effect of compound surface modification of shot peening and DLC coating on surface integrity and fatigue properties of gear steel 16Cr3NiWMoVNbE

Enhancing elevated-temperature fretting wear performance of GH4169 by tuning wear mechanism through laser shock peening

Effect of ultrasonic surface rolling process by disparate static pressure on a carburized layer of 17CrNiMo6 steel

A study of the effect of dual shot peening on the surface integrity of carburized steel: combined experiments with dislocation density-based simulations

Elastohydrodynamic Lubrication Characteristics of Spiral Bevel Gear Subjected to Shot Peening Treatment

Microstructure of Gear Steels Treated by Shot Peening by X-Ray Line Profile Analysis Method

Shot peening coverage effect on laser powder bed fused steel

The oil lubricated fretting wear behavior under different sliding displacements and frequencies of Ti6Al4V titanium alloy as affected by micro-shot peening

Effect of laser shock peening on fretting wear behaviour of AISI 304 stainless alloy

Investigation on Improving the Fretting Wear Properties of Ti6Al4V Alloy via Micro-shot Peening to Produce Surface Asperities and Surface Hardening Layer

A computational model of wear evolution for shot peened surfaces of gear steel

Surface integrity and transmission performance of spiral bevel gears subjected to shot peening: A comparison between concave and convex surfaces

Experimental Study on the Effect of Shot Peening and Re-Shot Peening on the Residual Stress Distribution and Fatigue Life of 20CrMnTi

Enhancing Tribological Properties of Pump Shafts through Shot Peening: A Study of Surface Roughness, Hardness and Performance Comparison with Heat Treatment

Improvement in the tribological behaviour of surface-nanocrystallised 304 stainless steel through supersonic fine particle bombardment