Abstract:Polyether ether ketone (PEEK) is introduced as a material for the additive manufacturing process called fused filament fabrication (FFF), as opposed to selective laser sintering (SLS) manufacturing. FFF manufacturing has several advantages over SLS manufacturing, including lower initial machine purchases costs, ease of use (spool of filament material vs powder material), reduced risk of material contamination and/or degradation, and safety for the users of the equipment. PEEK is an excellent candidate for FFF due to its low moisture absorption as opposed to other common FFF materials, such as Acrylonitrile Butadiene Styrene (ABS). PEEK has been processed into a filament and samples have been manufactured using several build orientations and extrusion paths. The samples were used to conduct tensile, compression, flexural, and impact testing to determine mechanical strength characteristics such as yield strength, modulus of elasticity, ultimate tensile strength and maximum elongation, etc. All tests were conducted at room temperature. A microscope analysis was also conducted to show features on the failures surfaces. The mechanical property results from this study are compared to other published results using traditional thermo-plastic manufacturing techniques, such injection molding. Tensile testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average ultimate tensile stresses were determined to be 73 MPa for 0° orientation, and 54 MPa for 90° orientation, with alternating 0°/90° orientations of 66.5 MPa. Compression testing was conducted at two raster orientations, 0° and alternating between 0° and 90°. Average ultimate strength for the single orientation direction was 80.9 MPa with the alternating orientations at 72.8 MPa. Flexural testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Ultimate flexural stress was determined to be 111.7 MPa for 0°, 79.7 MPa for 90°, and 95.3 MPa for orientations alternating between 0° and 90°. Finally, impact testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average impact energy absorbed was determined to be 17.5 Nm in the 0° orientation, 1.4 Nm in the 90° orientation, and 0.7 Nm for the alternating 0° and 90° orientations.

A systematic review of the process parameters, mechanical characteristics and applications of polyether ether ketone (PEEK) and its composites by additive manufacturing

Additive manufacturing of polyetheretherketone and its composites: A review

An overview on the influence of process parameters through the characteristic of 3D-printed PEEK and PEI parts

A review on the fused deposition modelling of fibre-reinforced polymer composites: Influence of process parameters, pre-processing and post processing techniques

Molding of polyether ether ketone (PEEK) and its composites: a review

Influence of Process Parameters on the Properties of Additively Manufactured Fiber-Reinforced Polymer Composite Materials: A Review

3D printed Polyether ether ketone (PEEK), Polyamide (PA) and its evaluation of mechanical properties and its uses in healthcare applications.

Applications of 3D-Printed PEEK via Fused Filament Fabrication: A Systematic Review

Effect of process parameters on additively manufactured parts using FDM process & material selection: A review

Fused Filament Fabrication of PEEK: A Review of Process-Structure-Property Relationships

Mechanical properties of additively manufactured polymeric composites using sheet lamination technique and fused deposition modeling: A review

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

Enhancing the mechanical properties of SCF/PEEK composites in FDM via process-parameter optimization

Mechanical Properties of Fused Deposition Modeling of Polyetheretherketone (PEEK) and Interest for Dental Restorations: A Systematic Review

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone

3D-Printed high performance PEEK/CF-PEEK polymer composites—An investigation on microstructural characteristics and mechanical performance

A critical review on the fused deposition modeling of thermoplastic polymer composites

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

EFFECTS OF EXTRUSION RATE AND POST-ANNEALING ON MECHANICAL PROPERTIES AND PRINTING QUALITY OF ADDITIVELY MANUFACTURED CARBON FIBER REINFORCED POLYETHERKETONEKETONE (PEEK) PARTS

On Mechanical, Physical, and Bioactivity Characteristics of Material Extrusion Printed Polyether Ether Ketone