Abstract:Recent innovations in battery technologies have facilitated the development and widespread use of electric vehicles (EVs), by increasing the energy density of batteries while lowering their cost. Despite the rapid growth of the EV market, the long charging time of lithium-ion batteries (LIBs) remains as a major obstacle for expanding customer acceptance of EVs. Typically, graphite-based anodes in the state-of-the-art LIBs suffer from Li plating under fast-charging conditions, which causes severe performance degradations and early cell failure of batteries. To prevent the Li plating-induced failure, extensive research efforts have been devoted to developing diagnostic methods capable of detecting Li plating. The electrochemical analysis of Li plating enables non-destructive, in operando detection without complicated experimental procedures or special equipment. Herein, we present a non-destructive method for detecting Li plating during fast-charge cycling by analyzing current transients during the constant-voltage charging step, based on electrochemical battery models. Three-dimensional (3D) and pseudo-two-dimensional (P2D) battery models are employed to predict the electrochemical behavior of full cells under fast-charging conditions. 3D model enables the evaluation of local electrochemical properties, such as local reaction current densities and electrode potentials, which are largely affected by the microstructure of the electrode. Furthermore, P2D models are employed to investigate the effect of changes in microstructural properties (e.g., porosity and fraction of active surface of the graphite anode) on electrochemical behavior of full cells. For 3D modeling, the 3D Voronoi tessellation and Catmull-Clark algorithm are employed to construct the model geometry of graphite anodes. 3D modeling results predict that upon fast-charging, the charge-transfer potential on the top surface of graphite anode rapidly drops below 0 V vs. Li/Li + , triggering Li plating. To extract the electrochemical signals of Li plating, the fast-charging behaviors of full cells are investigated by using the P2D model with a partially reversible Li plating–stripping reaction. In specific, the constant-current and constant-voltage (CC-CV) charging process of the full cells with graphite anodes is simulated with Li plating-induced degradation modes; reduction of (i) interparticle pores, (ii) active surface area for Li intercalation reaction, and (iii) cyclable Li amount. Modeling results demonstrate that an inflection point appears in the current transient curve, and it shows a positive shift when the Li plating-induced degradation occurs. Electrochemical tests and microstructural analyses further confirm the validity of proposed electrochemical detection of Li plating. This study provides an effective strategy to design electrochemical methods for Li plating detection during fast-charging batteries based on electrochemistry-based models.

Suppressing Lithium Metal Plating of Graphite Anode with Al2O3 and TiO2 for Fast-Charging Li-Ion Batteries

Reversible Li Plating on Graphite Anodes through Electrolyte Engineering for Fast-Charging Batteries.

Research Progress of Lithium Plating on Graphite Anode in Lithium‐Ion Batteries

The Boundary of Lithium Plating in Graphite Electrode for Safe Lithium-Ion Batteries.

Multi‐Interface Strategy for Electrode Tailoring Toward Fast‐Charging Lithium‐Ion Batteries

Effects of Electrolyte Additives and Solvents on Unwanted Lithium Plating in Lithium-Ion Cells

Analytical and Numerical Analysis of Lithium Plating Onset in Single and Bilayer Graphite Electrodes during Fast Charging

New insight on graphite anode degradation induced by Li‐plating

Head-Mounted coating on graphite host enabling highly reversible Li Plating/Stripping in Lithium-ion/Lithium metal hybrid anode

Electrochemistry-Based Diagnosis of Li Plating for Fast-Charging Li-Ion Batteries

High-Throughput Lithium Plating Quantification for Fast Charging Battery Design

Li Plating Regulation on Fast-Charging Graphite Anodes by a Triglyme-LiNO3 Synergistic Electrolyte Additive.

Challenges and Strategies of Fast-Charging Li-ion Batteries with a Focus on Li Plating

Sequential Effect of Dual‐Layered Hybrid Graphite Anodes on Electrode Utilization During Fast‐Charging Li‐Ion Batteries

Study on the Lithium Plating and Dissolution Behavior on Anode of Lithium Ion Battery

Visualized Detection of Lithium Plating on Graphite Anodes Cycled Under Low Temperature and Fast Charging

Unveiling Voltage Evolution During Li Plating-Relaxation-li Stripping Cycling of Lithium-Ion Batteries

Long Lifespan Lithium Metal Anodes Enabled by Al2O3 Sputter Coating

Eliminating Graphite Exfoliation with an Artificial Solid Electrolyte Interphase for Stable Lithium‐Ion Batteries

Low-Cost Al2o3 Coating Layer As A Preformed Sei on Natural Graphite Powder to Improve Coulombic Efficiency and High-Rate Cycling Stability of Lithium-Ion Batteries

Incorporating Α-Al2o3 Nanodots into Expanded Graphite Anodes Toward Stable Fast Charging for Lithium-Ion Batteries