Abstract:TiAl alloy is one of the most attractive candidates for a new generation of high-temperature structural materials and has broad application prospects in the aerospace field. As a typical intermetallic material, TiAl is inevitably difficult to process using conventional methods. Election beam selective melting (EBSM) is an effective method of addictive manufacturing to prepare TiAl alloy with a complex structure. However, the microstructure of TiAl alloy formed using EBSM often contains defects such as pores, which seriously reduces the mechanical properties of the material. In this work, the effects of EBSM and post-processing procedures on the microstructure and mechanical properties of Ti-48Al-2Cr-2Nb alloy were studied. The results show that the microstructure of Ti-48Al-2Cr-2Nb alloy formed using the EBSM process was dense and composed of equiaxed γ-phase and double-phase regions. A large number of dislocations that formed due to thermal stress were clearly observed inside the Ti-48Al-2Cr-2Nb alloy. When the EBSM process parameters were 13.5 mA, 4.0 m/s, and 40.50 J/mm3, as the current intensity increased, the Al content decreased, the content of α2 phase increased, and the microstructure of the material was coarse. The results of the tensile test fracture morphology indicate that the Ti-48Al-2Cr-2Nb alloy exhibited brittle fracture during tensile deformation, lacking the typical yield deformation of metal materials. As the energy density of the EBSM process increased, the mechanical properties of the Ti-48Al-2Cr-2Nb alloy first increased and then decreased. The samples prepared with an energy density of 34.50~40.50 J/mm3 had excellent mechanical properties, of which the maximum tensile strength and maximum elongation reached 643 MPa and 2.09%, respectively. The phase composition of the Ti-48Al-2Cr-2Nb alloy after hot isostatic pressing (HIP) treatment remained unchanged from the EBSM samples, but there was a slight difference in content. There was an increase in the amount of γ phase and a decrease in B2 phase, accompanied by the generation of a massive γ phase after HIP treatment. Moreover, the number of dislocations inside the material increased. The Ti-48Al-2Cr-2Nb alloy after HIP treatment exhibited obvious plastic deformation characteristics, with a tensile strength of 679 MPa and elongation of 2.5%. A heat treatment of 900 °C/5 h was performed on the Ti-48Al-2Cr-2Nb alloy after HIP. The dislocation density of the Ti-48Al-2Cr-2Nb alloy decreased, and the B2 phase transformed from massive to lamellar.

Metastable phase and microstructural degradation of a TiAl alloy produced via selective electron beam melting

High-temperature microstructure stability and fracture toughness of TiAl alloy prepared via electron beam smelting and selective electron beam melting

Hierarchical microstructure of a titanium alloy fabricated by electron beam selective melting

Microstructure and high-temperature tensile property of TiAl alloy produced by selective electron beam melting

Microstructure and mechanical properties of an in-situ TiB2 particle reinforced AlSi10Mg composite additive manufactured by selective electron beam melting

TiAl Alloy Fabricated Using Election Beam Selective Melting: Process, Microstructure, and Tensile Performance

Ti-48Al-2Cr-2Nb alloys prepared by electron beam selective melting additive manufacturing: microstructural and tensile properties

Effect of Process Parameters on Microstructure of TiAl Alloy Produced by Electron Beam Selective Melting

Diverse microstructure of Ti6.5Al2Zr1Mo1V fabricated via electron beam selective melting

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

High-strength and thermally stable TiB2-modified Al–Mn–Mg–Er–Zr alloy fabricated via selective laser melting

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Improvement on high-temperature tensile strength and ductility of selective electron beam melting TiAl alloys via small-strain forging

Research on aluminum component change and phase transformation of TiAl-based alloy in electron beam selective melting process under multiple scan

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Microstructure evolution and tensile property of TiAl alloy using continuous direct energy deposition technique

Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting

Effect of Heat Treatment on the Structure and Properties of Titanium Aluminide Alloy Ti–Al–V–Nb–Cr–Gd Produced by Selective Electron Beam Melting

Tuning microstructure and enhancing corrosion property of Ti-6Al-3Nb-2Zr-1Mo alloy through electron beam surface melting

Controlling the microstructure and mechanical properties of a metastable β titanium alloy by selective laser melting

Microstructural evolution and mechanical properties of Ti55531–0.5Nb fabricated by selective laser melting under different heat treatments