Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

High-efficiency and ultraviolet stable carbon-based CsPbIBr2 solar cells from single crystal three-dimensional anatase titanium dioxide nanoarrays with ultraviolet light shielding function

Low-temperature preparation of titanium dioxide thin layer for highly efficient CsPbI 3 perovskite solar cells

Low-temperature Preparation of Titanium Dioxide Thin Layer for Highly Efficient CsPbI3 Perovskite Solar Cells

High-Efficiency All-Inorganic Perovskite Solar Cells Tailored by Scalable Rutile TiO 2 Nanorod Arrays with Excellent Stability

In Situ Surface Fluorination of TiO 2 Nanocrystals Reinforces Interface Binding of Perovskite Layer for Highly Efficient Solar Cells with Dramatically Enhanced Ultraviolet‐Light Stability

Bifunctional Interface Engineering by Oxidating Layered TiSe 2 for High-Performance CsPbBr 3 Solar Cells

Bifunctional Passivation for Efficient and Stable Low-Temperature Processed All-Inorganic CsPbIBr2 Perovskite Solar Cells

Combustion-processed NiO/ALD TiO2 Bilayer As a Novel Low-Temperature Electron Transporting Material for Efficient All-Inorganic CsPbIBr2 Solar Cell

Performance Enhancement of Hole Transport Layer-Free Carbon-Based CsPbIBr2 Solar Cells through the Application of Perovskite Quantum Dots

Efficient Planar Perovskite Solar Cells with Low-Temperature Atomic Layer Deposited TiO2 Electron Transport Layer and Interfacial Modifier

2D/3D heterostructured CsPbI2Br solar cells: a choice for a monolithic all-perovskite tandem device

Numerical Simulation of All Inorganic CsPbIBr2 Perovskite Solar Cells with Diverse Charge Transport Layers using DFT and SCAPS-1D Frameworks

Recycling of FTO/TiO2 Substrates: Route Toward Simultaneously High-Performance and Cost-Efficient Carbon-Based, All-Inorganic CsPbIBr2 Solar Cells.

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

High-Efficiency (>14%) and Air-Stable Carbon-Based, All-Inorganic CsPbI2Br Perovskite Solar Cells Through a Top-Seeded Growth Strategy

A ternary organic electron transport layer for efficient and photostable perovskite solar cells under full spectrum illumination

Interfacial TiO2 Atomic Layer Deposition Triggers Simultaneous Crystallization Control and Band Alignment for Efficient CsPbIBr2 Perovskite Solar Cell

All-Inorganic Perovskite Solar Cells with Tetrabutylammonium Acetate as the Buffer Layer between the SnO 2 Electron Transport Film and CsPbI 3

2D Perovsktie Substrate-Assisted CsPbI 3 Film Growth for High-Efficiency Solar Cells

Lanthanide 3D Supramolecular Framework Boosts Stable Perovskite Solar Cells with High UV Utilization.

Significant efficiency enhancement of carbon-based CsPbI2Br perovskite solar cells enabled by optimizing tin oxide electron transport layer