Abstract:This paper reports a grain regrowth and bifacial passivation strategy to reduce recombination losses for wide‐bandgap perovskite solar cells. As a result, PCEs of 21.9% and 19.9% are achieved for the opaque and semitransparent perovskite solar cells, respectively. Furthermore, a perovskite/silicon 4‐terminal (4‐T) tandem cell with an attractive PCE of 29.8% is realized. The wide‐bandgap perovskite solar cell is a crucial part of perovskite/silicon tandem solar cells, which offer an avenue for surpassing the power conversion efficiency (PCE) limit of single‐junction silicon solar cells. However, the actual efficiency of such tandem solar cells today is diminished by the nonradiative recombination losses in the wide‐bandgap perovskite subcells. Here, this work reports a grain regrowth and bifacial passivation (GRBP) strategy to reduce recombination losses at the grain boundaries and perovskite/charge transport layer interfaces simultaneously. This is achieved by a posttreatment of perovskite films with a mixture of methylammonium thiocyanate (MASCN) and phenethylammonium iodide (PEAI). The MASCN induces the regrowth of perovskite grains and simultaneously facilitates the penetration of PEAI into the hole‐transport‐layer (HTL)/perovskite bottom interface. Thereby, the bulk and interface nonradiative recombination losses are reduced and the open‐circuit voltage in solar cells is considerably increased. PCEs of 21.9% and 19.9% for the 1.65‐eV bandgap opaque and semitransparent perovskite solar cells, respectively, are obtained. The encapsulated semitransparent perovskite solar cells retain their initial efficiency following 500 h of operation under one‐sun illumination in ambient conditions. The perovskite/silicon 4‐terminal (4‐T) tandem cells are fabricated with impressive PCEs 29.8% and 28.5% for 0.049 cm2 and 1 cm2 devices, respectively.

Nanocrystal‐Enabled Front‐Surface Bandgap Gradient for the Reduction of Surface Recombination in Inverted Perovskite Solar Cells

Synergy of Front‐Surface Energy‐Level Gradient and Lattice Anchoring Effect for Enhancing Perovskite Solar Cell Performance

Perovskite Solar Cells with Front Surface Gradient

Constructing Ultra-Shallow Near-Edge States for Efficient and Stable Perovskite Solar Cells

Synergistic passivation and energy level alignment by graphene quantum dots for high performance inverted CsPbI3 perovskite solar cells

Gradient bandgap enables >13% efficiency sulfide Kesterite solar cells with open-circuit voltage over 800 mV

Surface in situ reconstruction of inorganic perovskite films enabling long carrier lifetimes and solar cells with 21% efficiency

Constructing an Interfacial Gradient Heterostructure Enables Efficient CsPbI3 Perovskite Solar Cells and Printed Minimodules

A Surface‐Reconstructed Bilayer Heterojunction Enables Efficient and Stable Inverted Perovskite Solar Cells

Surface p-type band bending and energy level alignment minimizes voltage loss in perovskite solar cells

Reducing nonradiative recombination in perovskite solar cells with a porous insulator contact

Nano-capillary induced assemble of quantum dots on perovskite grain boundaries for efficient and stable perovskite solar cells

Strontium‐Doped CsPbI 3 Quantum Dots as an Interfacial Layer for Efficient Inorganic Perovskite Solar Cells

Enhanced Photovoltage for Inverted Planar Heterojunction Perovskite Solar Cells

Grain Regrowth and Bifacial Passivation for High‐Efficiency Wide‐Bandgap Perovskite Solar Cells

Infiltrated 2D/3D Heterojunction with Tunable Electric Field Landscape for Robust Inverted Perovskite Solar Cells with over 24% Efficiency

Surface n-type band bending for stable inverted CsPbI3 perovskite solar cells with over 20% efficiency

Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells

Synchronous surface reconstruction and grain boundary healing toward efficient and stable inverted CsPbI3 perovskite solar cells

High Efficient Hole Extraction and Stable All-Bromide Inorganic Perovskite Solar Cells via Derivative-Phase Gradient Bandgap Architecture

In Situ Reconstruction of Hole‐Selective Perovskite Heterojunction with Graded Energetics Toward Highly Efficient and Stable Solar Cells