Abstract:NiO nanomaterials prepared using a solid–liquid NH3·H2O precipitation method (NiO-NSL) were tested in the catalytic combustion of methane. The NiO-NSL presented a characteristic rod-like nanostructure with a length of about a few hundred nanometers except for a part of the nanoparticles. For comparison, the NiO nanomaterials prepared by the traditional liquid-phase NH3·H2O precipitation method (NiO-NLL) were tested in the same reaction conditions. NiO-NSL exhibited significantly higher methane combustion activity than NiO-NLL and achieved the complete combustion of methane at 390 °C, which was outstanding in non-noble metal-based catalyst. X-ray photoelectron spectroscopy (XPS) and hydrogen-temperature-programmed reduction (H2-TPR) results indicate that the surface Ni2+ content of NiO-NSL was higher than that of NiO-NLL, and the presence of more Ni2+ might be responsible for the enhanced activity. DFT calculations prove that the energy barrier for C–H bond activation on Ni2+ was lower than that on Ni3+, which was consistent with the higher methane catalytic combustion activity of NiO-NSL. In addition, when the precipitating agent was replaced with NaOH and (NH4)2CO3, the generalization of the solid–liquid precipitation method in the preparation of the NiO catalysts was also tested. The results show that the solid–liquid precipitation method proposed in this work was still applicable when NaOH was used as a precipitant. However, with the use of (NH4)2CO3 as a precipitant, the methane catalytic activity of the NiO nanoparticles prepared by the solid–liquid precipitation method was reduced to a certain extent compared with the traditional liquid-phase precipitation method. This research can open up a highly efficient and environmentally friendly method for the synthesis of methane combustion catalysts.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.1c00732?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.1c00732</a>.Stability test results of NiO-NSL (Figure S1); wide-angle XRD patterns of the as-precipitated samples using (NH4)2CO3 as the precipitant and a standard xNiCO3·yNi(OH)2 sample (Figure S2); representative TEM images of the precursors and as-calcined catalysts of the other four samples (Figures S3 and S4); specific performance data of samples in previous research (Table S1); XPS analysis of the other samples (Table S2, Figures S5 and S6); H2-TPR profiles of the other samples (Table S3, Figures S7 and S8); detailed DFT calculation results (Table S4); the surface model used in the calculations (Figure S9) (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.1c00732/suppl_file/an1c00732_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Tuning lattice defects to facilitate the catalytic performance of Ni–Cu–O hybrid nanoparticles towards methane oxidation

Cutting the cost to combust methane by embellishing the Co-O-Cu interaction in Cu-incorporated Co 3 O 4 -based nanocatalysts

Incorporating Si into NiO support to facilitate oxygen activation for CH 4 combustion

A Supported Nickel Catalyst Stabilized by a Surface Digging Effect for Efficient Methane Oxidation

Investigation of catalytic methane oxidation over Ag/Co2MOx (M = Co, Ni, Cu) catalysts with varying interfacial electron transfer

Nickel Oxide As an Effective Catalyst for Catalytic Combustion of Methane

One-Step Synthesis of Nanostructured Cu–Mn/TiO 2 via Flame Spray Pyrolysis: Application to Catalytic Combustion of CO and CH 4

Irregularly Shaped NiO Nanostructures for Catalytic Lean Methane Combustion

Electron transferring with oxygen defects on Ni-promoted Pd/Al 2 O 3 catalysts for low-temperature lean methane combustion

In-situ fabrication of Cu-Mn-O nanostructure catalysts on Ti mesh and their catalytic property optimization for low-temperature and stable CO oxidation

Insight into the moderate interaction between the metal and support and reinforcing of Ni/SiO 2 -based catalysts efficiency with the manganese integration in thermal catalytic methane decomposition

Regulation of Ni-CNT Interaction on Mn-Promoted Nickel Nanocatalysts Supported on Oxygenated CNTs for CO2 Selective Hydrogenation.

Bimetallic Ni-Co nanoparticles on SiO2 as robust catalyst for CO methanation: Effect of homogeneity of Ni-Co alloy

Single-Cation Catalyst: Ni Cation in Monolayered CuO for CO Oxidation

Nickel and manganese oxide heterostructure nanoparticles supported by carbon nanotube for highly efficient oxygen evolution reaction catalysis

Nickel Hydroxide Nanosheets Prepared by a Direct Manual Grinding Strategy for High-Efficiency Catalytic Combustion of Methane

Construction of Co/Mn-based nanowires with adjustable surface state for boosting lean methane catalytic oxidation

Denary oxide nanoparticles as highly stable catalysts for methane combustion

Uniformly Dispersed Nano Pd-Ni Oxide Supported on Polyporous CeO2 and Its Application in Methane Conversion of Tail Gas from Dual-Fuel Engine

Solid-State Construction of CuOx/Cu1.5Mn1.5O4 Nanocomposite with Abundant Surface CuOx Species and Oxygen Vacancies to Promote CO Oxidation Activity

Enhancing CO catalytic oxidation performance over Cu-doping manganese oxide octahedral molecular sieves catalyst