Abstract:The primary purpose of this study was to evaluate the hydraulic coefficient of coarse aggregate grain size beds and hydraulic parameters under random and perpendicular bed configurations, as well as to explore the discharge coefficient for rectangular weirs. The research objectives were to compare flow resistance coefficients, evaluate the discharge coefficient for rectangular weirs, investigate the relationship between roughness coefficient and hydraulic parameters, and validate the theoretical hydraulic equation for the rectangular weir. This was achieved by analysing different bed configurations, bed slopes, and 20 and 30-mm bed materials. Sieve analysis was conducted on bed materials using American-standard sieves to determine their particle size distribution. The experiment was performed in a rectangular flume measuring 12 m in length, 0.31 m in width, and 0.45 m in depth. In a laboratory experiment, water was pumped into a flume using centrifugal pumps, and a rectangular weir was attached downstream for discharge measurement. The experiment investigated factors such as Manning roughness coefficient, bed material geometry, bed slope, and weir shapes. Approximately 1680 tests were conducted to analysed the impact of these factors on discharge and the coefficient of discharge. The average Manning's roughness coefficients for a grain size of 20 mm were 0.019 (with weir) and 0.019 (without weir) in a random bed configuration, and 0.028 (with weir) and 0.027 (without weir) in a perpendicular flow bed configuration. For a grain size of 30 mm, the coefficients were 0.023 (with weir) and 0.022 (without weir) in a random bed configuration, and 0.033 (with weir) and 0.026 (without weir) in a perpendicular flow bed configuration. The presence of a weir has affected Manning's roughness coefficients and discharge coefficients. With a weir, the roughness coefficients have generally been higher compared to without a weir, indicating increased roughness in the channel. The discharge coefficient for a rectangular weir with a grain size of 20 mm ranged from 0.39 to 0.84 (random bed) and 0.27 to 0.68 (perpendicular flow bed), while for a grain size of 30 mm it ranged from 0.31 to 0.81 (random bed) and 0.23 to 0.48 (perpendicular flow bed). The discharge coefficients have varied depending on the grain size and bed configuration, reflecting different flow efficiencies over the weir. Rough particles influenced flow and Manning's roughness coefficient value, then reduced discharge and velocity values. Under two bed configurations and slopes, beds with a grain size of 30 mm have higher roughness coefficients compared to those with a grain size of 20 mm. The models have shown that the roughness coefficient is inversely proportional to the discharge and directly proportional to the tailgate water levels. The coefficient of roughness and discharge coefficient are mainly influenced by the channel slopes, bed roughness, bed grain size, and bed configuration. A randomly configured bed with a 20 mm grain size gravel bed is preferred over a perpendicular bed configuration to handle high discharges. Using a 20 mm grain-size gravel bed in open-channel flow is more suitable than a 30 mm grain-size bed. Relying on the constant friction factor, Manning's n, is not recommended as it may result in design errors. These findings have the potential to improve hydraulic engineering design practices, enhancing the accuracy and efficiency of open-channel flow systems.

Effect of sediment deposition on the efficiency of Fayoum weir

Application and Design of an Efficient Siphon Dewatering System for Debris Flow Mitigation: A Case Study of a Small Catchment in Zhejiang Province, China

THE EFFECT OF FLOW CONDITIONS AND GEOMETRIC PARAMETERS ON THE SCOUR VALUE DOWNSTREAM COMPOSITE STRUCTURES OF WEIR AND GATE

Effect of Using Weirs Downstream of Parallel Submerged Jets from Opened Multiple Sluice Gates

On the effect of flow regime and slope of the channel bed on the hydraulic performance of the sharp-crested rectangular side weir: a numerical simulation

Bed configurations downstream combined V-Notch-sharped edged Weir with inverted V-Shaped gate

Acclimatize experimental approach to adjudicate hydraulic coefficients under different bed material configurations and slopes with and without weir

Investigation of flow characteristics downstream vertical sluice gates of Bahr Yousef regulator physical model

An Investigating of the Impact of Bed Flume Discordance on the Weir-Gate Hydraulic Structure

Discharge Formula Based on Brink Depth Over Sharp-Crested Weirs

Experimental Study on the Hydraulic Performance of Porous Broad-Crested Weirs with Sloping Crests

Regime equations development for the design of Egyptian sandy canals

Effects of ramp slope and discharge on hydraulic performance of submerged hump weirs

Research on Relationships Between Sediment Yield and Hydraulics Parameters on Slope

The effect of geometry parameters and flow characteristics on erosion and sedimentation in channels junction using finite volume method

FOULING ANALYSIS ON ENERGY DISSIPATION ORIFICE PLATES WITH SEDIMENT CONTAINED WATER FLOW

Hydraulic characteristics of a sluice gate over a broad-crested weir

Experimental and numerical assessment of hydraulic characteristic of a new semi-frustum weir in the pool-weir fishway

Flow through a sluice gate over a broad crested weir under free- and submerged-flow conditions

Numerical Modeling of Flow over a Rectangular Broad-Crested Weir with a Sloped Upstream Face

Effect of Sediment Concentration on Hydraulic Characteristics of Energy Dissipation in a Falling Turbulent Jet