Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Investigation on Hot Deformation Behavior and Microstructure Evolution of Lean Duplex Stainless Steel 2101 during Elevated Temperature Compression Testing

Effect of hot deformation mode on the microstructure evolution of lean duplex stainless steel 2101

MICROSTRUCTURE EVOLUTION OF LEAN DUPLEX STAINLESS STEEL 2101 DURING HOT DEFORMATION

Strain Rate Dependence of Hot Tensile Behavior, Microstructure Evolution, and Fracture Mechanism of Lean Duplex Stainless Steel 2101

Microstructure evolution and dynamic recrystallization mechanisms of 316L stainless steel during hot deformation

Investigation on the Hot Deformation Behavior of 316L Stainless Steel Using 3D Processing Map

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot Deformation Behavior of a New Austenite–ferrite Duplex Stainless Steel Containing High Content of Nitrogen

Microstructure Evolution and Mechanical Properties of Lean Duplex Stainless Steel Bars Prepared by a Short Process

Hot Deformation Behavior of Duplex Stainless Steel 2205

On Microstructure Characterization of Fe–Cr–Ni–Mo–N Super-Austenitic Stainless Steel During Hot Deformation

Hot Deformation Behavior and Microstructure Evolution of the Maraging Stainless Steel

Investigation of the Hot Deformation Behavior of 22Cr‐25Ni Austenitic Heat‐Resistant Steel by Combining Constitutive Model and Processing Map

Effect of the Rate and Temperature of Hot Deformation on Strain Resistance of Duplex Stainless Steel

Using the Physically Based Constitutive Model and Processing Maps to Understand the Hot Deformation Behavior of 2304 Lean Duplex Stainless Steel

Hot Compression Behavior of 18Cr–11Mn–0.06Ni–0.19N High‐Mn Ultralow Nickel Duplex Stainless Steel under Large Deformation

Hot Workability of a Spray Formed 2195 Aluminum-Lithium Alloy Based on an Improved Isothermal Processing Map and Drx ‘C-Curve’

Investigation on Hot Compression Precipitation and Recrystallization Behavior of 23.7Cr–2.2Ni–1.3Mo–14Mn–0.26N High‐Manganese Low‐Nickel Duplex Stainless Steel

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Development of a Novel Cr21 Lean Duplex Stainless Steel and Its Hot Deformation Behavior

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys