Abstract:Metallic components fabricated with powder bed fusion additive manufacturing (AM) processes are known to have defects arising from liquid-solid phase transformation. Friction stirring can be an effective alternative source of heat, as evidenced in some of the recently developed powder deposition-based solid-state AM processes. However, they possess practical issues such as making compacted powder feedstock beforehand, consolidation of powder filler inside the tool during deposition followed by necessary extrusion, and significant flash formation, among a few. This paper proposed a novel powder bed friction stir (PBFS) additive manufacturing process inside a specifically designed mould that could potentially mitigate such issues in the existing technologies. The process was successfully demonstrated by building single-track and parallel double-track 3D structures layer-by-layer from an AA6061 powder bed using a rotating non-consumable friction stirring tool. Furthermore, for a better understanding of the underlying process mechanics, deposits were analyzed for their surface topography, microstructural evolution, and mechanical performance under different heat inputs as well as different print locations. Different heat inputs were applied by varying the friction-stirring pitch (FS pitch) from 'Low' to 'High'. The print locations analysis was carried out in a parallel double-track fabricated at the optimal FS pitch. The results revealed that the 'High' FS pitch yielded an increased percentage of recrystallized grains and a fraction of high-angle grain boundaries as well as a larger average grain size due to the high heat input, better material intermixing, and the dominance of continuous dynamic recrystallization. As a result, an improved mechanical performance, except for the microhardness, was observed. The 'High' FS pitch also exhibited an improved surface topography. The results also revealed that the relative dominance of the re-stirring-induced recrystallization and the reheating-induced plastic deformation was the key factor for the variation of the microstructure in the longitudinal, transverse, and short-transverse directions. A gradual decrease in the tensile strength was observed from the 'Top' to the 'Bottom' segments of the overlapped region, contrary to the central region of a track.

Additive friction stir deposition induced stress ripples in aluminum alloy

Influence of Friction Stir Additive Manufacturing Parameters on Dry Friction and Wear Properties of Al-Mg-Si Alloy's Built Surfaces Fabricated by Sheet Lamination

Evolution of Material Properties and Residual Stress with Increasing Number of Passes in Aluminium Structure Printed via Additive Friction Stir Deposition

Microstructural and Mechanical Characterization of Additive Friction Stir-Deposition of Aluminum Alloy 5083 Effect of Lubrication on Material Anisotropy

A multi modal approach to microstructure evolution and mechanical response of additive friction stir deposited AZ31B Mg alloy

SolidStir Additive Manufacturing: A Novel Deformation-Based Additive Manufacturing Using Friction Stir Technology

Heterogeneous microstructure development in additive friction-stir deposited Al-Mg-Si alloy

Thermo-mechanical process variables driven microstructure evolution during additive friction stir deposition of IN625

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

A Novel Approach for Enhanced Mechanical Properties in Solid-State Additive Manufacturing by Additive Friction Stir Deposition Using Thermally Stable Al-Ce-Mg Alloy

Anisotropy and mechanical properties of dissimilar Al additive manufactured structures generated by multi-layer friction surfacing

Development and analysis of a powder bed friction stir (PBFS) additive manufacturing process for aluminium alloys: A study on friction-stirring pitch (ω/v) and print location

Residual Stress Analysis of Additive Manufactured A356.2 Aluminum Alloys using X-Ray Diffraction Methods

Experimental and numerical studies of re-stirring and re-heating effects on mechanical properties in friction stir additive manufacturing

Dynamic Behavior Characterization of Aluminum Alloy 7020 Manufactured Using the Additive Friction Stir Deposition Process

Effect of rotational speed and feed rate on microstructure and mechanical properties of 6061 aluminum alloy manufactured by additive friction stir deposition

Effect of multi-layer deposition in solid-state friction stir surfacing-based additive manufacturing for fabrication of large-scale metal product

Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited

Friction stir-based additive manufacturing

Understanding the strain localization in additively manufactured materials: Micro-scale tensile tests and crystal plasticity modeling

Additive Friction Stir-Enabled Solid-State Additive Manufacturing for the Repair of 7075 Aluminum Alloy