Analysis of the Impact of Environmental Temperature and Humidity on Cotton Fiber Quality During Initial Processing

Yaosheng ZhuJianhao ZhangXudong ZhaoHong XuCollege of Apparel,Xinjiang University,Urumqi,Xinjiang,China

DOI: https://doi.org/10.1080/15440478.2024.2338538

2024-04-27

Journal of Natural Fibers

Abstract:This study examines the impact of temperature and humidity on cotton fiber quality during initial processing. Conducted in a Xinjiang cotton ginning mill, we used the USTER HVI1000 to analyze five quality indices: upper half mean length, uniformity, short fiber index, tensile strength, and elongation. Results indicated that temperatures below 13°C increased fiber brittleness, moisture, and significantly reduced length and strength. Optimal conditions were observed at temperatures between 13°C to 20°C with normal humidity, where length and strength were maintained. Above 20°C, the dry environment led to a decrease in these indices. While higher temperatures and lower humidity helped remove impurities and lessen cotton knots, relative humidity below 45% increased static electricity and knots. Despite data limitations, this study moves towards identifying optimal temperature and humidity levels for improving cotton quality during initial processing, providing a theoretical foundation for future enhancements. 研究了棉花初加工过程中温度和湿度对棉花纤维各项质量指标的影响. 在新疆某轧棉厂进行了广泛的跟踪试验和取样,采用USTERHVI1000大容量棉纤维测试仪对棉花样品的上半部分平均长度、整齐度、短纤维指数、断裂强力比和断裂伸长率五项指标进行了测试和分析. 结果表明,当轧棉环境温度低于1°C3°C时,轧棉后棉纤维脆性增加,表面潮湿,长度和强度指标显著下降. 当轧棉环境温度在3°C~10°C之间时,相对湿度正常,轧棉后棉花的长度和强度指标相对较好. 然而,当轧棉环境温度超过10°C时,环境变得干燥,棉花的长度和强度指标再次呈下降趋势. 较高的温度和较低的相对湿度有利于去除杂质,减少棉花结的形成,但当相对湿度降至45%以下时,会产生静电,棉花结的数量有增加的趋势. 目前,由于数据的限制,无法获得最准确的数据,但随着实验数据的增加,我们将对温度和湿度有更准确的了解,这有助于提高棉花在初始加工过程中的质量. 这将为提高棉纤维初加工的各项指标提供理论依据.

materials science, textiles

What problem does this paper attempt to address?

This paper aims to study the impact of environmental temperature and humidity on cotton fiber quality during the initial processing of cotton. Specifically, the research involves extensive tracking tests and sampling at a cotton ginning factory in Xinjiang, using the USTER HVI1000 high-capacity cotton fiber tester to test and analyze five indicators of cotton samples: upper half mean length, uniformity, short fiber index, breaking strength ratio, and breaking elongation rate.

The research results indicate:
1. When the environmental temperature is below 13°C, the brittleness of cotton fibers increases, and the surface becomes moist, leading to a significant decline in length and strength indicators.
2. In the temperature range of 13°C to 20°C with normal humidity, the length and strength of cotton fibers maintain a good state.
3. When the temperature exceeds 20°C, the dry environment causes these indicators to decline again.
4. Higher temperatures and lower humidity help remove impurities and reduce the formation of cotton knots; however, when the relative humidity drops below 45%, static electricity is generated, and the number of cotton knots increases.

Despite data limitations, this study provides a theoretical basis for further optimizing environmental conditions during the initial processing of cotton, which helps improve cotton quality. This is of great significance for enhancing the competitiveness of the Xinjiang cotton industry.