Abstract:Magnesium alloys have received much attention for their lightweight and other excellent properties, such as low density, high specific strength, and good castability, for use in several industrial and commercial applications. However, both magnesium and its alloys show limited room-temperature formability owing to the limited number of slip systems associated with their hexagonal close-packed crystal structure. It is well known that crystallographic texture plays an important role in both plastic deformation and macroscopic anisotropy of magnesium alloys. Many authors have concentrated on improving the room- temperature formability of Mg alloys. However, despite having a lot of excellent properties in magnesium alloy, the study for various properties of magnesium alloy have not been clarified enough yet.Mg alloys are known to have a good damping capacity compared to other known metals and their alloys. Also, the damping properties of metals are generally recognized to be dependent on microstructural factors such as grain size and texture. However, there are very few studies on the relationship between the damping capacity and texture of Magnesium alloys. Therefore, in this study, specimens of the AZ31 magnesium alloy, were processed by hot working, and their texture and damping property investigated. A 60 mm × 60 mm × 40 mm rectangular plate was cut out by machining an ingot of AZ31 magnesium alloy (Mg-3Al-1Zn in mass%), and rolling was carried out at 673 K to a rolling reduction of 30%. Then, heat treatment was carried out at temperatures in the range of 573-723 K for durations in the range of 30-180 min. The samples were immediately quenched in oil after heat treatment to prevent any change in the microstructure. Texture was evaluated on the compression planes by the Schulz reflection method using nickel-filtered Cu Kα radiation. Electron backscatter diffraction measurements were conducted to observe the spatial distribution of various orientations. Specimens for damping capacity measurements were machined from the rolled specimen, to have a length of 120 mm, width of 20 mm, and thickness of 1 mm. The damping capacity was measured with a flexural internal friction measurement machine at room temperature. It was found that the damping capacity increases with both increasing heat-treatment temperature and time, due to grain growth and the increased pole densities of textures.

Determining the microstructure and properties of magnesium aluminum composite panels by hot rolling and annealing

Experimental study on properties and structure of magnesium alloy/PC/ABS hybrid materials prepared by hot-press molding technology

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Microstructure and mechanical behavior of Mg ZK60/Al 1100 composite plates fabricated by co-extrusion

Study on the work-hardening behavior and tissue property analysis of high-strength magnesium alloy

Annealing coordinates the deformation of shear band to improve the microstructure difference and simultaneously promote the strength-plasticity of composite plate

Response Mechanism of Mechanical Behavior with Mg Plate Microstructure Evolution During Al/Mg/Al Composite Plate Rolled by hard Plate

Effect of annealing treatment on the microstructure and mechanical properties of bulk nanostructured Ti/AZ61 composites prepared by hot pressing

Mechanical Properties and Microstructure of AM140 Magnesium Alloy

Microstructure, mechanical properties and thermal conductivity of the short carbon fiber reinforced magnesium matrix composites

The Effect of Ti Particles Addition on the Microstructure and Mechanical Behavior of Mg AZ31/Al 6082 Composite Sheets

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effect of differential temperature on the interfacial microstructure evolution and mechanical properties of asymmetrically rolled Mg/Al composite plates

Effect of hot working on the damping capacity and mechanical properties of AZ31 magnesium alloy

Study on the Influence of Prefabricated Aluminum Layer Technology on the Properties of Corrugated Interface Steel/Aluminum/Aluminum Alloy Composite Panel

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Response mechanism of matrix microstructure evolution and mechanical behavior to Mg/Al composite plate by hard-plate accumulative roll bonding

Effects of Annealing Treatment on Mechanical and Damping Properties of ZK60 Magnesium Alloy Sheets

Micro-structural and tensile strength analyses on the magnesium matrix composites reinforced with coated carbon fiber

Effect of thickness ratio on microstructure evolution and coordinated behavior of Mg/Al composite plates in one-pass asymmetric rolling with differential temperature rolls