Abstract:Adsorption is considered to be a promising butanol recovery method for solving the issue of inhibition in the ABE (acetone-butanol-ethanol) fermentation. As a byproduct in the second generation biobutanol industry, lignin was found to be a good adsorbent for the butanol enrichment. It is conducive to the full utilization of renewable lignocellulose biomass resource. Kinetic and equilibrium experiments indicated that lignin had a satisfactory adsorption rate and capacity that are comparable to those of many synthetic materials. Multicomponent adsorption experiments revealed that lignin had higher adsorption selectivity toward butanol than that of ethanol and acetone. The adsorption capacity of lignin for butanol first increased and then gradually decreased with increasing temperature. And maximum adsorption capacity reached 304.66 mg g−1 at 313 K. The inflection point of temperature is close to the ABE fermentation temperature of 310 K. The condensed butanol by desorption was 145 g L−1, with a satisfying regeneration performance. 1H NMR and FT-IR spectra indicated that the aromatic units of lignin formed π-systems with A/B/E. The π-system is particularly significant for butanol due to its longer hydrocarbon chain. These results could contribute to the emerging lignin-based materials for butanol separation.

What problem does this paper attempt to address?

This paper attempts to address the problem of how to efficiently and economically separate butanol from ABE fermentation broth during the production of biobutanol. Specifically, the paper explores the use of lignin as an adsorbent to separate butanol from ABE fermentation broth, aiming to overcome the high energy consumption and low efficiency issues associated with traditional separation methods. ### Background and Issues 1. **Importance of Biobutanol**: Biobutanol, as a clean fuel, has advantages such as high energy density, low corrosiveness, low volatility, low hygroscopicity, and ease of blending with gasoline. It is considered one of the most promising biofuels to replace gasoline. 2. **Challenges of ABE Fermentation Process**: Biobutanol is mainly obtained through acetone-butanol-ethanol (ABE) fermentation. However, the butanol produced during fermentation inhibits cell growth, causing fermentation to stop when the butanol concentration reaches 13 g/L. Additionally, due to the low concentration of butanol, traditional separation methods like distillation are costly and the energy consumption is almost equal to the energy content of butanol itself. 3. **Advantages of Adsorption Method**: The adsorption method has gained widespread attention due to its lower energy consumption. However, existing adsorbent materials such as activated carbon, polymer resins, molecular sieves, and metal-organic frameworks (MOFs) are costly and have limited availability. ### Research Objectives 1. **Using Lignin as an Adsorbent**: Lignin is the most abundant natural aromatic macromolecule in nature and a by-product of the second-generation biobutanol industry. The study aims to explore the potential application of lignin as an adsorbent in butanol separation. 2. **Improving Resource Utilization**: By utilizing lignin, the study aims to fully utilize renewable lignocellulosic biomass resources and reduce the cost of butanol production. 3. **Evaluating Adsorption Performance**: The study investigates the adsorption rate, adsorption capacity, and adsorption thermodynamic properties of lignin, and evaluates its selectivity for butanol through multi-component adsorption experiments. ### Main Research Content 1. **Adsorption Isotherm Experiments**: The study investigated the adsorption isotherms of acetone, butanol, and ethanol on lignin, finding that lignin has the highest adsorption capacity for butanol. 2. **Adsorption Kinetics Experiments**: The study explored the kinetics of butanol adsorption on lignin, finding that lignin reaches adsorption equilibrium within 50 minutes. 3. **Competitive Adsorption Experiments**: The study evaluated the selectivity of lignin for butanol in a ternary solution containing other fermentation products, showing that lignin has a high selectivity for butanol. 4. **Adsorption Thermodynamics Analysis**: The study investigated the adsorption thermodynamic parameters of lignin for butanol at different temperatures, finding an optimal adsorption temperature of 313 K. 5. **Regeneration Performance Testing**: The study evaluated the regeneration performance of lignin through five adsorption-desorption cycles, showing good regeneration performance. ### Conclusion 1. **Adsorption Performance of Lignin**: Lignin has a higher adsorption capacity for butanol compared to acetone and ethanol, reaching a maximum adsorption amount of 304.66 mg/g at 313 K. 2. **Economics and Sustainability**: Lignin, as an adsorbent, is low-cost, renewable, and biodegradable, making it an economically feasible material for butanol separation. 3. **Potential Applications**: The research results indicate that lignin has good application prospects in separating butanol from ABE fermentation broth, contributing to the development of the biobutanol industry.

Separation of biobutanol from ABE fermentation broth using lignin as adsorbent: A totally sustainable approach with effective utilization of lignocellulose

Lignin-based thermo-sensitive hydrogel for selective recovery of butanol from dilute solution

Preparation of Water-Insoluble Lignin Nanoparticles by Deep Eutectic Solvent and Its Application As a Versatile and Biocompatible Support for the Immobilization of Α-Amylase.

Artificial Symbiosis for Acetone-Butanol-ethanol (ABE) Fermentation from Alkali Extracted Deshelled Corn Cobs by Co-Culture of Clostridium Beijerinckii and Clostridium Cellulovorans.

Progress of Acetone-Butanol Fermentation Coupled with Separation

Kraft lignin from Jackfruit waste as an adsorbent for the selective recovery of biobutanol from the Acetone-Butanol-Ethanol fermentation broth

Highly Efficient Semi-Continuous Extraction and In-Line Purification of High β-O-4 Butanosolv Lignin

The advanced strategy for enhancing biobutanol production and high-efficient product recovery with reduced wastewater generation

Energy efficient design of bio-butanol purification process from acetone butanol ethanol fermentation

Selection and optimization of a salting‐out extraction system for recovery of biobutanol from fermentation broth

Reduction wastewater discharge in second-generation acetone-butanol-ethanol (ABE) fermentation process by adsorptive removal of organic acids toward the broth recycling system

Separation of 2,3-Butanediol from Fermentation Broth via Cyclic and Simulated Moving Bed Adsorption Over Nano-MFI Zeolites

Holistic lignocellulosic biorefinery approach for dual production of bioethanol and xylonic acid coupled with efficient dye removal

Developing a separation system to enable real-time recovery of acetone-butanol during fermentation

Production of butanol from lignocellulosic biomass: recent advances, challenges, and prospects

Benzenesulfonic acid-based hydrotropic system for achieving lignocellulose separation and utilization under mild conditions

Structure changes of lignin and their effects on enzymatic hydrolysis for bioethanol production: a focus on lignin modification

Extraction Of Lignin From Wood Biomass Using A New Ionic Liquid At Open Atmosphere

Process optimization of acetone-butanol-ethanol fermentation integrated with pervaporation for enhanced butanol production

Revisiting alkali pretreatment to transform lignocellulose fermentation with integration of bioprocessible lignin

Selective lignin arylation for biomass fractionation and benign bisphenols