Abstract:The increase in the use of energy from forest biomass has increased the demand for knowledge about tree-chipping operations. Therefore, this study aimed to evaluate the effect of different drying times of wood logs and various combinations of knife and anvil configurations in the horizontal chipper on the quality of Eucalyptus dunnii chips produced for energy purposes. The study was conducted in a seven-year-old stand of E. dunnii. A horizontal chipper was used to chip whole trees and obtain nine types of chips, resulting from the interaction between the three drying times of the trees and three configurations of the horizontal chipper. The chips were characterized, followed by an evaluation of energy quality for comparison between the treatments. Among the outcomes discerned, it became evident that the employed wood exhibited a Basic Density (0.506 g.cm-³). The chip dimensions and bulk density presented notable disparities owing to the distinct chipper configurations and tree drying time. The extended drying period (150 days) conferred a lower average moisture content (34.20%) to the study materials. Moreover, the ash content was lower in the treatment with 150 drying days (0.52%). Both the useful calorific value and the Fuel Value Index were also greater in the treatment (150 drying days), measuring 2600.00 kcal kg-1 and 128.06 cal cm-3, respectively. In the analysis of the Fuel Value Index concerning chipper configurations, it was observed that for chips featuring a granulometry of 25 mm, the treatment involving 150 days of drying, four knives, and one shim proved the most efficient (Q = 0.979). Conversely, for chips with a granulometry of 16 mm, the treatment involving 150 days of drying, eight knives, and one shim emerged as the most efficient (Q = 0.970). Consequently, the proposed index is efficacious and underscores the necessity of adapting knife settings in response to moisture content changes to maintain the desired granulometry and apparent density standards.

Chloride leaching of eucalyptus wood particles by water for pellets production

Impact of Chemical Composition on Eucalyptus Wood Clones for Sustainable Energy Production

Torrefaction as a Pretreatment Technology for Chlorine Elimination from Biomass: A Case Study Using Eucalyptus globulus Labill

Decontamination of CCA-treated eucalyptus wood waste by acid leaching

Assessing Proximate Composition, Extractive Concentration, and Lignin Quality to Determine Appropriate Parameters for Selection of Superior Eucalyptus Firewood

Pretreated Eucalyptus globulus and Pinus radiata Barks: Potential Substrates to Improve Seed Germination for a Sustainable Horticulture

Cypress Wood and Bark Residues Chemical Characterization and Utilization as Fuel Pellets Feedstock

Eco Valorization of Eucalyptus globulus Bark and Branches through Liquefaction

Feasibility of co-disposal of lignite and eucalyptus wood in coal-fired power plants: thermogravimetric characterization, typical gaseous pollutant emission characteristics, and economic analysis

Selective fractionation and enzymatic hydrolysis of Eucalyptus nitens wood

Leaching Laws of Micro/Nano Particles from Eucalyptus camaldulensis Wood

Effects of Alkaline Extraction on Micro/Nano Particles of Eucalyptus Camaldulensis Biology

Steam explosion of lignocellulosic residues for co-production of value-added chemicals and high-quality pellets

Combustion of pellets produced from corn straw and cashew nut shell in residential and industrial scenarios: Chemical, thermal and emission analyses

Impact of supercritical extraction on solid fuel wood pellet properties and off-gassing during storage

Short rotation woody crops and forest biomass sawdust mixture pellet quality

Effect Extraction Methods on Micro/Nano Particles Leaching from E. Camaldulensis Wood

Quality of eucalyptus wood chips for bioenergy as a function of drying time and horizontal chipper settings

Energy usage of spruce with waste face masks and spent coffee grounds as fuel in a pellet boiler

Physical–mechanical properties of wood from a eucalyptus clone planted in an integrated crop-livestock-forest system

Performance of eucalypt particleboard with the addition of farm waste