Abstract:The materials used in variable temperature conditions are required to have excellent thermal fatigue performance. The effects of laser shock processing (LSP), solid solution and aging treatment (T6), and cryogenic treatment (CT) on both microstructure and thermal fatigue performance of ZCuAl10Fe3Mn2 alloys were studied. Microstructure and crack morphology were then examined by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The result showed that, after being subjected to the combination treatment of T6+CT+LSP, the optimal mechanical properties and thermal fatigue performance were obtained for the ZCuAl10Fe3Mn2 alloy with the tensile strength, hardness, and elongation of 720 MPa, 300.16 HB, and 16%, respectively, and the thermal fatigue life could reach 7,100 cycles when the crack length was 0.1 mm. Moreover, the ZCuAl10Fe3Mn2 after combination treatment shows high resistance to oxidation, good adhesion between the matrix and grain boundaries, and dramatically reduced growth rate of crack. During thermal fatigue testing, under the combined action of thermal and alternating stresses, the microstructure around the sample notch oxidized and became loose and porous, which then converted to micro-cracks. Fatigue crack expanded along the grain boundary in the early stage. In the later stage, under the cyclic stress accumulation, the oxidized microstructure separated from the matrix, and the fatigue crack expanded in both intergranular and transgranular ways. The main crack was thick, and the path was meandering.

Performance of different microstructure on electrochemical behaviors of laser solid formed Ti–6Al–4V alloy in NaCl solution

Salt spray corrosion behavior and electrochemical performance of Al and Ti reinforced Ni60 coating by laser cladding

Improved corrosion and long‐term immersion behavior in 3.5 wt% NaCl solution of laser powder bed fusion produced Ti5Cu after heat treatment

Electrochemical Behavior of Laser Powder Bed Fusion (L-PBF) Ti–6Al–4V Alloy: Influence of Phase and Grain Boundaries on Surface Passive Film Formation

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Metastable pitting corrosion behavior and characteristics of passive film of laser powder bed fusion produced Ti–6Al–4V in NaCl solutions with different concentrations

Electrochemical dissolution and passivation of laser additive manufactured Ti6Al4V controlled by elements segregation and phases distribution

Effects of laser shock processing, solid solution and aging, and cryogenic treatments on microstructure and thermal fatigue performance of ZCuAl10Fe3Mn2 alloy

Effect of Solid-Solution Treatment on Corrosion and Electrochemical Behaviors of Mg-15Y Alloy in 3.5 Wt.% NaCl Solution

Electrochemical dissolution behavior of heat treated laser solid formed Inconel718

Microstructure, corrosive-wear and electrochemical performance of laser cladded NiTi–xAl 2 O 3 coatings in 3.5%NaCl solution

The effect of heat treatment on corrosion behavior of selective laser melted Ti-5Al-5Mo-5V-3Cr-1Zr alloy

Comparison on the Electrochemical Corrosion Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion and Casting

Effects of Heat Treatments on Microstructures and Mechanical Properties of Ti6Al4V Alloy Produced by Laser Solid Forming

Corrosion and passivation behavior of laser powder bed fusion produced Ti-6Al-4V under various prior plastic deformation strains

Passivation behavior of water‐quenched and heat‐treated Ti‐6Al‐4V in Hank's solution

Effect of heat treatment on the microstructure and in-situ corrosion behavior of SLM-NiTi alloys

Tailoring surface properties and corrosion resistance of laser shock peened Ti6Al4V alloy by low-temperature annealing

Corrosion Behavior of As-Cladding Al 0.8 CrFeCoNiCu 0.5 Si x High Entropy Alloys in 3.5% NaCl Solution

Corrosion Behavior on Orthopedic NiTi Alloy with Nanocrystalline/amorphous Surface

Effect of Heat Treatment on Corrosion Performance of Mg-12Gd-3Y-1Sm-0.8Al Alloy