Abstract:There is a rapid progression toward spacecraft miniaturization due to the prospect of reduced launch costs, the requirement for satellite constellations, and the integration of microelectromechanical systems (MEMS). Satellite propulsion is required for increased mission flexibility and orbital debris mitigation, but down-scaling of such devices has proven non-trivial. Some electrostatic thrusters are both challenging and promising given their increase in performance with small geometry, but the relatively low thrust produced through ion acceleration limits their mission applicability. For this reason, it may be desirable to produce thrusters that are able operate across a wide range of specific impulses, depending on maneuver time, thrust bit requirements, and several other factors that influence propulsion system selection. At RAPPEL, a bimodal thruster that can operate at high specific impulse with electrospray propulsion or high thrust using cold gas expansion has been developed. Inevitably, such a propulsion system comes with complications related to performance characterization. A novel and economical data acquisition system has been established to measure the performance of both modes in high vacuum. For the cold gas mode, a torsional thrust balance was built in-house to measure thrust levels between 1 − 15 m N , and can be easily modified for lower ranges. The natural frequency of the thrust stand was measured to be 5.6 H z . The vacuum system sustained pressures below 5 m b a r while the cold gas nozzle operated, and 1.3 × 10 − 5 m b a r during electrospray operation. A 3-D printed linear cold gas nozzle was used to validate the thrust stand. Its thrust was close to 9 m N at a mass flow rate of 20 m g / s of nitrogen, producing a specific impulse of just under 45 s . Due to the noise present in thrust stand measurements at the sub- m N force-level produced by electrosprays, the thrust stand was built to also accommodate a complementary ion beam current measurement system. The power processing unit, used to generate square-wave ± 2500 V signals using optodiodes, was built to operate a bipolar ionic liquid ion source (ILIS). The rise and fall times of the push/pull switch were close to 1 m s and 30 m s , respectively. The electrical power system used to operate the electrospray and measure its performance is examined in detail, followed by the results from validation of both data acquisition systems.

Endurance testing and characterization of a novel candidate for CubeSat propulsion: The Advanced Cusp Field Thruster (ACFT)

Development of Electric and Chemical Microthrusters

The Development of a Next-Generation Latticed Resistojet Thruster for CubeSats

Optimization, Test and Diagnostics of Miniaturized Hall Thrusters

Development and Laboratory Testing of a CubeSat-Compatible Staged Ionic-Liquid Electrospray Propulsion System

Development and Qualification of Green Propellant Micropump for MicroSat and CubeSat Propulsion Systems

A Pulsed Vacuum Arc Ion Thruster for SmallSat Applications

The KM-10 Hall-Effect Thruster: Development Status and Application Prospects

Direct thrust test and asymmetric performance of porous ionic liquid electrospray thruster

UWE-4: First Electric Propulsion on a 1U CubeSat—In-Orbit Experiments and Characterization

Design of an Intake and a Thruster for an Atmosphere-Breathing Electric Propulsion System

Applied-Field Magnetoplasmadynamic Thrusters for Deep Space Exploration

Space micropropulsion systems for Cubesats and small satellites: From proximate targets to furthermost frontiers

Mission analysis of a 1U CubeSat post-mission disposal using a thin-film vacuum arc thruster

System Analysis and Test-Bed for an Atmosphere-Breathing Electric Propulsion System using an Inductive Plasma Thruster

Thrust Model and Trajectory Design of an Interplanetary CubeSat with a Hybrid Propulsion System

Active Attitude Control for Microspacecraft; A Survey and New Embedded Designs

Development of a microthrust balance and ion beam measurement system: Characterizing a dual-mode thruster for spacecraft

Development and test of a cost-efficient gridded ion thruster propulsion system for small satellites – IonJet

CubeSat testing of Coulomb drag propulsion

The Reliability Modeling and Evaluation of a Cusped Field Thruster When Undertaking a Gravitational Wave Detection Mission