Abstract:The service life of products is significant for ensuring stable and reliable performance of these products, such as spacecraft, military equipment and electronic equipment. Such service life is generally evaluated by measuring the working duration of products before losing efficacy or breaking down through tests under the same working condition with the real working condition. However, with the rapid increasing improvements in reliability and of products, the service life of products had been lengthen remarkably, the corresponding time and financial costs of the conventional simulated products life tests were continuously increasing, and such costs were becoming too high to be accepted. On this basis, the concept of accelerated test was suggested as a potential solution in which appropriate equivalent of products service life should be selected. The tests were accelerated by adjusting the changing rate of the equivalent, so that the test durations were shortened under a certain equivalent. In 1980s, the Accelerate Life Test（ALT） and the Accelerate Degradation Test（ADT） based on ALT, which estimated the reliability and service life of products under common stress levels through the accelerate test data under higher stress levels were suggested. ALT and ADT were the most common accelerated test methods, in which the failure possibility function were regarded as the equivalent. In other accelerated tests, the selected equivalent also included surface topography and condition parameters. As for accelerated wear test, there were numerous models for quantitative prediction of wear, which was a typical form of the degradation process of materials, the equivalent of wear could be selected based on these quantitative wear models. This paper aimed to propose an accelerated wear test method based on an accurate quantitative wear model. The investigations were conducted based on friction and wear with experiment condition of surface contact and mixed lubrication by the standard apparatus for typical mechanical seal material pair 9Cr18Mo/M234A0. The structure of tested seal ring was modified to reduce temperature rise and strengthen the fluid dynamic pressure effect. In this paper,the accelerated wear model was established with the entropy increase as equivalent of wear, based on the dissipation wear model which considered the wear as an irreversible thermodynamic process. The dissipation wear model was verified with the mentioned seal pair, revealing a linear relationship between wear rate and entropy increase. By modifying the entropy increase rate under the same entropy increase, the wear test duration was shortened. On this basis,this accelerate wear model was verified with equivalent wear tests with long time/low entropy increase and short time/high entropy increase. This model was also compared with accelerate wear model based on Archard model. The result of which revealed that wear test of 200 min duration could be equally replaced by a wear test of 10 min duration with an error of 2.22%, and the maximum relative error of other time was 4.75%. The feasibility and the accuracy of this accelerate wear model was proved preliminarily by the test results of this study. Further investigation revealed that the wear mechanism was invariable during the tests in this paper.

The Evaluation of Wear Life Based on Accelerated Test through Analysis of Correlation between Wear Rate and Lubricant Film Parameter

Simulation Analysis for Lubrication State of the Thrust Washer Within Straight Planetary Gear Set

Experimental Analysis On Oil Film Properties Of Plane Port Pair In Axial Piston Machine

Real-time Measurement on Lubrication Characteristic Parameters of Plane Port Pair in Axial Piston Pumps

Accelerated Wear Test Design Based on Dissipation Wear Model Entropy Analysis under Mixed Lubrication

Accelerate Wear Test under Mixed Lubrication Condition Based on Dissipation Wear Model for Typical Mechanical Seal Pair

Research on Wear Prediction of Piston/cylinder Pair in Axial Piston Pumps

Prediction on the reliable life of sliding wear by the accelerated wear test

Volumetric efficiency degradation prediction of axial piston pump based on friction and wear test

The Effect of Wear on the Performance of a Rotary Lip Seal

Tribological Behavior Analysis of Valve Plate Pair Materials in Aircraft Piston Pumps and Friction Coefficient Prediction Using Machine Learning

Coupled evolution process of lubrication and wear in piston-liner interface of high-pressure common rail pumps

Theoretical investigation and experimental validation of wear in conjugate rolling friction pairs of two-dimensional piston pumps

Predicting Fatigue Life for Finite Line Contact under Starved Elastohydrodynamic Lubrication Condition

Evaluation of Dynamic Parameters and Improvement of Wear Resistance of Involute Gears when Using Film-Forming Lubricants

Research on gear life reliability analysis based on accelerated life test

Study on the wear characteristics of hydrodynamic seals during start-up based on cross-scale contact mechanics

Wear Characteristics of the Material Specimen and Method of Predicting Wear in Floating Spline Couplings of Aero-Engine

Predicting Film Parameter and Friction Coefficient for Helical Gears Considering Surface Roughness and Load Variation

Wear Condition Monitoring and Working Pattern Recognition of Piston Rings and Cylinder Liners Using On-Line Visual Ferrograph

A Model of Cylindrical Gear Failures Using the Criterion of the Working Surface Wear Resistance