Abstract:In order to improve the full utilization of wheat straw, to enhance the mechanical properties of gypsum board and to increase the fire resistance of wood-based gypsum board, a new preparation process of gypsum-based composites with wheat straw was put forward in this study. The thick and small wheat straw fiber were used as the reinforcing materials in gypsum-based composites, and their dimension were in the range of 0.30-0.60 and 0.18-0.30 mm, respectively. The gypsum was employed as the continuous phase in the composites. The ambient temperature curing structural adhesive was used to replace the traditional gypsum retarder in the new preparation process of gypsum-based composites. The preparation process consisted of an initial forming stage for initial strength and a curing stage, where the objectives were gypsum hydration and the strength further increased, respectively. Compared with the conventional gypsum composites with Chinese fir fiber and Chinese fir particle, the mechanical properties and fire resistance of gypsum-based composites by adding wheat straw fiber with different dimension were tested and analyzed. The results showed that the physical and mechanical properties of gypsum-based composites with small wheat straw fiber were lower than those of gypsum-based composites with Chinese fir fiber, but were better than gypsum-based composites with thick wheat straw fiber. The internal bond strength, modulus of rupture, modulus of elasticity and thickness swelling of gypsum-based composites with small wheat straw fiber were 0.33 MPa, 7.1 MPa, 2 370 MPa and 2.82%, respectively, and could meet the requirements of gypsum particleboard standard. According to the lower thermal conductivity and higher ash content of wheat straw than wood materials, the time to ignition of gypsum-based composites with wheat straw was higher than that of gypsum-based composites with Chinese fir fiber, and there was no obvious peak heat release rate in the fire resistance test. Compared with the gypsum-based with Chinese fir fiber and Chinese fir particle, the total heat release of gypsum-based composites with small wheat straw fiber was 48.18% and 35.87% lower, respectively. The main peak of CO2 production rate was 42.25% and 38.81% lower than that of Chinese fir fiber and particle gypsum composites, respectively. The main peak of CO production rate was comparable to wood-gypsum composites. The weight percent retains of small wheat straw fiber gypsum composites was slightly higher than that of Chinese fir gypsum composites, and the appearance after burning test was more complete and the degree of carbonization was lighter obviously. Due to the smooth outer surface of the wheat straw, the gypsum was mainly attached to the internal surface of the wheat straw by microscopic observation using scanning electron microscope. Therefore, the small straw fiber could increase the contact area between the internal surface and the gypsum, which indicated the inherent reason for the better physical and mechanical properties of small wheat straw fiber gypsum composites. The smooth outer surface of the wheat straw was almost covered with SiO2, which also explained the superior fire resistance of wheat straw gypsum composites. The study can be a reference for the performance improving on the gypsum-based composites with wheat straw fiber and its application in project.

Preparation and properties study of straw fiber cement-based composite boards with efficient formaldehyde purification function

Mechanical and Water Soaking Properties of Medium Density Fiberboard with Wood Fiber and Soybean Protein Adhesive.

Study on Epoxy Resin Composite Reinforced with Rice Straw Fiber

Mechanical properties and fire resistance of gypsum-based composites with wheat straw

Effect of Chemical Treatment on Rice Straw Fiber Surface and Properties of Straw/Polylactic Acid Composites

Flexural Strength and Thermal Conductivity of Fiber-Reinforced Calcium Silicate Boards Prepared from Fly Ash

Preparation of Plastics- and Foaming Agent-Free and Porous Bamboo Charcoal based Composites Using Sodium Silicate as Adhesives

Preparation of Hot-Pressed Wheat Straw Board by Self-Adhesive Process: Effects of Raw Material Sizes and Acid/Alkali Pretreatment

A Study on Fire Retardant and Soundproof Properties of Stainless Steel EAF Reducing Slag Applied to Fiber Reinforced Cement Boards

Development of a new magnesium oxychloride cement board by recycling of waste wood, rice husk ash and flue gas desulfurization gypsum

Toward Novel Biocomposites from Unavoidable Food Supply Chain Wastes and Zirconia

Effect of Multi-Hydroxyl Polymer-Treated MUF Resin on the Mechanical Properties of Particleboard Manufactured with Reed Straw

Characterization of composite material from the copolymerized polyphenolic matrix with treated cassava peels starch

Tunable Physical-Mechanical Properties of Eco-Friendly and Sustainable Processing Bamboo Self-Bonding Composites by Adjusting Parenchyma Cell Content

Study on the Application of Desulfurization Gypsum for the Gypsum Fiber Board Production

Production of Biodegradable Board Using Rape Straw and Analysis of Mechanical Properties

The preparation of CaCO3/wood composites using a chemical precipitation method and its flame-retardant and mechanically beneficial properties

Comparison of Properties of Poly(Lactic Acid) Composites Prepared from Different Components of Corn Straw Fiber

Functionalized flattened bamboo board: In-situ immersion assembly of flame-retardant, waterproof and anti-mold composite coatings

Eco-friendly fiberboards with low formaldehyde content and enhanced mechanical properties produced with activated soybean protein isolate modified urea-formaldehyde resin

Influence of hot-pressing temperature and density on the physical and mechanical properties of bamboo scrimber