Tashni's first tunnel

Robert Blasiak

DOI: https://doi.org/10.1038/d41586-024-01282-3

IF: 64.8

2024-05-09

Nature

Abstract:Nature, Published online: 08 May 2024; doi:10.1038/d41586-024-01282-3 Digging deep.

multidisciplinary sciences

What problem does this paper attempt to address?

Boring Technology and Practice for Small Section Tunnel under Complicated Geological Conditions

Xia Yiping,Xia Yu,Liu Jun

DOI: https://doi.org/10.3969/j.issn.0559-9342.2010.10.014

2010-01-01

Abstract:The reasonable drilling and blasting program for the tunnel construction under complicated geological conditions is the key for surrounding rock stability and construction safety.As the different construction effect of emulsion explosives to nitramine explosives for multi-fractured rock,limiting the maximum dosage,taking millisecond delay blasting,changing the charging structure and using reasonable control technique can effectively improve the quality of chamber when using emulsion explosives.
Development of surface settlement of twin tunnels under the influence of the river

Liang Jiaxin,Tang Xiaowu,Wang Tianqi,Lin Weikang,Li Keyi,Xiang Qingqing

2024-01-01

International Journal of Geomate

Abstract:Soft soil poses more challenges to the construction of shallow-buried tunnels than other soils: the surrounding rock mass is more easily disturbed, and the tunnel stability is more influenced by groundwater seepage. The research is based on the Zizhi Tunnel project, a shallow-buried twin tunnel in soft soil. This paper divides the research area into the inside and outside river-affected area respectively. From the field monitoring data, the settlement law can be summarized, which found that for a single monitoring point, outside a river-affected area, the entire settlement development stage can be clearly divided into three stages: slow growth, rapid growth stage, and gradual convergence; however, inside the river-affected area, the settlement in the last stage will not converge but will continue to develop. Compared with the vault settlement, the surface settlement inside the river-affected area develops slower than that outside the river-affected area, which shows good consistency with the monitoring data. The synchronization of the sinking rate and stability of vault settlement and surface settlement verifies that the river over the tunnel has an impact on the development of surface settlement by the groundwater seepage in the soft soil. Based on field monitoring data, a numerical model is established to investigate the influence of the river on the surface settlement of the twin tunnels, of which the numerical results show the same development law as the monitoring data.
Statistical Approach to Tunneling Time in Attosecond Experiments

Durmus Demir,Tugrul Guner

DOI: https://doi.org/10.1016/j.aop.2017.09.009

2017-09-25

Abstract:Tunneling, transport of particles through classically forbidden regions, is a pure quantum phenomenon. It governs numerous phenomena ranging from single-molecule electronics to donor-acceptor transition reactions. The main problem is the absence of a universal method to compute tunneling time. This problem has been attacked in various ways in the literature. Here, in the present work, we show that a statistical approach to the problem, motivated by the imaginary nature of time in the forbidden regions, lead to a novel tunneling time formula which is real and subluminal (in contrast to various known time definitions implying superluminal tunneling). This entropic tunneling time, as we call it, shows good agreement with the tunneling time measurements in laser-driven He ionization. Moreover, it sets an accurate range for long-range electron transfer reactions. The entropic tunneling time is general enough to extend to the photon and phonon tunneling phenomena.

Quantum Physics,Mesoscale and Nanoscale Physics,Atomic Physics
Exis memoria

Hannya Kay

DOI: https://doi.org/10.1038/d41586-024-03908-y

IF: 64.8

2024-12-05

Nature

Abstract:Nature, Published online: 04 December 2024; doi:10.1038/d41586-024-03908-y Tales to tell.

multidisciplinary sciences
Geotechnical insights of mammal burrows in loose desert sand

Idil Deniz Akin,Sera Tirkes,Clint E. Collins

DOI: https://doi.org/10.1007/s11440-023-02000-5

2023-07-31

Acta Geotechnica

Abstract:Loose desert sand poses a constraint for geotechnical engineers to construct tunnels without a lining, which is typically steel, concrete, or slurry shield. Many desert mammals, however, can construct tunnels in loose sand, and the tunnels can remain stable over extended periods of time in harsh desert environments. This study presents the state of knowledge on mammal burrows in loose desert sand and provides insights from a geotechnical engineering perspective with the aim of understanding how desert mammals tackle a geotechnical challenge. The study presents these desert mammals as biogeotechnical engineers and explains their burrow stability using three fundamental soil mechanics principles: (i) unsaturated soil mechanics, (ii) compaction, and (iii) soil cementation. Damara mole-rats, kangaroo rats, pocket gophers, and round-tailed ground squirrels are presented as the desert biogeotechnical engineers. Proof-of-concept experiments conducted with a poorly graded fine sand demonstrate the effects of the fundamental soil mechanics principles used by the animals on soil strength. A limit equilibrium tunnel stability analysis performed using sand from a kangaroo rat habitat in the Sonoran Desert also demonstrated the link between tunnel stability of desert mammals and the three geotechnical principles.

engineering, geological
Geomorphological and sedimentary features of an underwater lava tube: the Túnel de la Atlántida (Lanzarote, Spain)

Javier Lario,Tamara Martín-Pozas,Sergio Sanchez-Moral,Juan Carlos Cañaveras,Angel Fernandez-Cortes,Roberto Cano,Cecilio Lopez-Tercero,Alvaro Roldan,Esther Martin,Carlos Perez-Mejias,Hai Cheng

DOI: https://doi.org/10.5194/egusphere-egu23-6059

2023-01-01

Abstract:The Túnel de la Atlántida (Atlantida Tunnel), located in Lanzarote Island (Canary Islands, Spain), with a length of about 2000 m and a depth of 64 m, is the largest submerged lava tunnel in the world. It corresponds to the submerged part of the lava tube complex of the La Corona volcano, with a length of about 10 km. During the development of the Sublantida Project, using diving techniques, various forms associated with the formation of the volcanic tube have been catalogued and a study of its sediments, minerals and speleothems has been carried out, including XRD, ESEM and petrological microscopy. It has been possible to propose a paleoenvironmental reconstruction from the formation of the volcanic tube, ca.21 Ka ago, to the present. The geomorphological, petrological, and sedimentary characteristics associated with the formation of the lava tube justify its importance as a World Geological Site of Interest.Acknowledgments: This project has received funding from the Spanish Ministry of Science and Innovation and the Spanish State Research Agency (grants CGL2017-91218-EXP and PID2019-110603RB-I00-SUBSYST). It is a contribution to the IGCP Project 725.
Reinforcing Tunnel Network Exploration in Proteins Using Gaussian Accelerated Molecular Dynamics

Nishita Mandal,Bartlomiej Surpeta,Jan Brezovsky

DOI: https://doi.org/10.1101/2024.04.30.591887

2024-05-16

Abstract:Tunnels are structural conduits in biomolecules responsible for transporting chemical compounds and solvent molecules to and from the active site. They have been shown to be present in a wide variety of enzymes across all functional and structural classes. However, the study of such pathways is experimentally challenging because they are typically transient. Computational methods such as molecular dynamics (MD) simulations have been successfully proposed to explore tunnels. Conventional MD (cMD) provides structural details to characterize tunnels but suffers from sampling limitations to capture rare tunnel openings on longer timescales. Therefore, in this study, we explored the potential of Gaussian accelerated MD (GaMD) simulations to improve the exploration of complex tunnel networks in enzymes. We used the haloalkane dehalogenase LinB and its two variants with engineered transport pathways, which are not only well-known for their application potential but have also been extensively studied experimentally and computationally regarding their tunnel networks and their importance in multi-step catalytic reactions. Our study demonstrates that GaMD efficiently improves tunnel sampling and allows the identification of all known tunnels for LinB and its two mutants. Furthermore, the improved sampling provided insight into a previously unknown transient side tunnel (ST). The extensive conformational landscape explored by GaMD simulations allowed us to investigate in detail the mechanism of ST opening. We determined variant-specific dynamic properties of ST opening, which were previously inaccessible due to limited sampling of cMD. Our comprehensive analysis supports multiple indicators of the functional relevance of the ST, emphasizing its potential significance beyond structural considerations. In conclusion, our research proves that the GaMD method can overcome the sampling limitations of cMD for the effective study of tunnels in enzymes, providing further means for identifying rare tunnels in enzymes with potential for drug development, precision medicine, and rational protein engineering.

Bioinformatics
Tunneling Nanotubes in the Brain

Dimitri Budinger,Vivian Baker,Michael T Heneka

DOI: https://doi.org/10.1007/978-3-031-62036-2_10

Abstract:Tunneling nanotubes (TNTs) have emerged as intriguing structures facilitating intercellular communications across diverse cell types, which are integral to several biological processes, as well as participating in various disease progression. This review provides an in-depth analysis of TNTs, elucidating their structural characteristics and functional roles, with a particular focus on their significance within the brain environment and their implications in neurological and neurodegenerative disorders. We explore the interplay between TNTs and neurological diseases, offering potential mechanistic insights into disease progression, while also highlighting their potential as viable therapeutic targets. Additionally, we address the significant challenges associated with studying TNTs, from technical limitations to their investigation in complex biological systems. By addressing some of these challenges, this review aims to pave the way for further exploration into TNTs, establishing them as a central focus in advancing our understanding of neurodegenerative disorders.
3D Simulation of TBM Excavation in Brittle Rock Associated with Fault Zones: the Brenner Exploratory Tunnel Case

Kai Zhao,Michele Janutolo,Giovanni Barla,Guoxing Chen

DOI: https://doi.org/10.1016/j.enggeo.2014.07.002

IF: 6.902

2014-01-01

Engineering Geology

Abstract:Brittle fault zones represent a major challenging geological environment for TBM tunnelling in deep Alpine tunnels, particularly when the faults are near parallel to or cross the tunnel axis at a low angle. This is the case of the Brenner Exploratory Tunnel in Italy. Serious local instabilities occurred at the left side wall during TBM drive in the granitic rocks associated with a sub-vertical fault zone, parallel to the tunnel axis. The segmental lining was collapsed at a distance of more than 2D (D is tunnel diameter) behind the face, without any evidence. The deformation and failure then propagated intensively to nearby, previously stabilized sections with a length of approximately 60 m in the longitudinal direction, leading to a subsequent damage of the shields and grippers of the machine and to a stoppage of the excavation in almost 4 months.To deal with these severe geotechnical problems encountered when tunnelling through a fault zone, a realistic 3D numerical simulation based on a site investigation and characterisation of the fault zone, can provide a helpful decision aid as they give a quantitative assessment of the potential mode of failure. In the case of the Brenner Exploratory Tunnel, the behaviour of the rock mass is neither ductile nor brittle, but governed by the combination due to the presence of the brittle fault zone. This paper focuses on the 3D simulation of such complex failure evolution. Special emphasis is placed on the modelling of the fault zone and of the TBM excavation process. The results demonstrate the role that the local rock mass condition and the complex interaction between the rock mass, the TBM components, and the tunnel support play on the characterization of this instability phenomenon. (C) 2014 Elsevier B.V. All rights reserved.
Ant nest geometry, stability, and excavation–inspiration for tunneling

Meron Belachew,Karie Yamamoto,Elliot Nichols,Danrong Zhang,J. David Frost,Chloé Arson

DOI: https://doi.org/10.1007/s11440-024-02232-z

2024-02-13

Acta Geotechnica

Abstract:Underground construction and tunnel excavation are known to redistribute stresses and cause ground displacement. Analytical solutions for stress distribution typically break down at shallow depths or in soil masses that exhibit high spatial variability, making numerical simulations necessary. Seeking to find new geometries and excavation strategies for underground construction, we propose to look to nature for inspiration. We extract 3D digital twins of Florida Harvester ant ( Pogonomyrmex Badius ) structures from a nest cast in situ and simulate the stress and displacement fields around that nest with the Finite Element Method (FEM). Stress invariants around the main shaft are compared to those around idealized geometric representations of that shaft, i.e., helixes with a fixed pitch angle and a uniform elliptical cross-section. Helical structures made of circular cross-sections and horizontally oriented elliptical cross-sections interact in a way that reduces the risk of tension failure and distributes the shear stress more evenly. One can show that in addition to the extra stability that they offer and the lower risk of tensile or shear failure that they exhibit, helical shafts have the advantage of requiring less power to excavate than straight sub-vertical shafts.

engineering, geological
Mechanical behaviors of surrounding rock and supporting structure of shallow-buried unsymmetrical pressure tunnel crossing soil–rock interface

Zhinan Hu,Ji Zhang,Yonggang Wang,Yunfei Wang

DOI: https://doi.org/10.3389/feart.2022.1113430

IF: 2.9

2023-01-06

Frontiers in Earth Science

Abstract:Shallow bias tunnels are sensitive at the entrance section, where the existence of soil–rock interface (SRI) results in more complex deformation of surrounding rock and supporting structure. This study investigates the mechanical properties of surrounding rock and supporting structure of a shallow-buried bias tunnel crossing the soil–rock interface by a combination of model tests and numerical simulations. A shallow-buried biased tunnel with significant cracking at its entrance section is selected in southwest China. The plastic zone distribution, deformation, and pressure of surrounding rock, as well as the stress and deformation of supporting structure, are analyzed under different conditions with the tunnel vault, arch haunch, arch spring, and wall foot crossing the soil–rock interface. The test and numerical results show that the internal force of the lining structure is the largest at the left arch haunch and the right arch spring, with cracks occurring in the project. The surrounding rock and supporting structure are most prominently influenced by the arch haunch and arch spring crossing the soil–rock interface among different positions of the tunnel. The supporting structure is subjected to stress in three modes: there is mainly shearing when the tunnel vault passes through the soil–rock interface, extrusion and shearing co-exist when the tunnel arch haunch and arch spring pass through the soil–rock interface, and extrusion is dominant when the tunnel wall foot passes through the soil–rock interface. Inserting grouting steel pipes perpendicular to the soil–rock interface on the deep-buried side of the tunnel can effectively control the deformation of surrounding rock and the stress of supporting structure.

geosciences, multidisciplinary
Las Leñas International Tunnel – Geomechanical challenges in large‐scale tunneling projects across The Andes

Rodrigo Orellana,Giorgio Höfer‐Öllinger,Juan Carlos Ulloa,Alejandro Flores Bertoglio

DOI: https://doi.org/10.1002/geot.202300001

2023-03-16

Geomechanik und Tunnelbau

Abstract:Developing large‐scale tunnelling projects in orogenic regions implies enormous technical challenges. Las Leñas International Tunnel Project through the Andes Main Cordillera of Chile and Argentina has been a long‐awaited infrastructure project, whose geological and topographic settings suggest several complex singularities to be considered, analyzed, and assessed during its development. Throughout the course of this feasibility study, the complex geological subsurface interpretation offers a broad spectrum of technical demands to be fulfilled. The overburden conditions, the presence of certain lithologies such as expansive clays or soluble evaporitic sequences, along with regional stress assessment, are major technical challenges. Through extensive geological, geotechnical, and hydrogeological mapping, subsurface 3D modelling interpretation, along with numerical analysis and its relationship with similar projects in the region, brittle, and plastic behaviour are analyzed. A wide range of modern techniques are used to assess those mentioned tasks, which enable an extensive comprehension of the geological and geotechnical conditions of the area. The purpose of this contribution is to enrich the knowledge on geological and geomechanical challenges faced in large tunnelling infrastructure projects in high‐mountain environments and what specific lessons may arise from them for similar future projects. Las Leñas International Tunnel – Geomechanische Herausforderungen bei großen Tunnelbauprojekten in den Anden Die Entwicklung groß angelegter Tunnelbauprojekte in orogenen Regionen impliziert enorme technische Herausforderungen. Der internationale Tunnel Las Leñas durch die zentralen Anden in Chile und Argentinien ist ein lang erwartetes Infrastrukturprojekt. Seine geologischen und topografischen Rahmenbedingungen zeigen komplexe Singularitäten auf, die während der Projektierung berücksichtigt, analysiert und bewertet werden müssen. Die Interpretation des komplexen geologischen Aufbaus bot im Zuge dieser Machbarkeitsstudie ein Spektrum an technischen Anforderungen: Die Überlagerungshöhe, Lithologien wie expansive Tone oder Evaporitgesteine sowie der regionale Spannungszustand führten zu technischen Herausforderungen. Auf Basis umfangreicher geologischer, geotechnischer und hydrogeologischer Kartierungen, Erstellung und Interpretation des Untergrunds in 3D‐Modellen sowie numerischer Analysen wurde unter Einbeziehung ähnlicher Projekte in der Region sprödes und plastisches Verhalten analysiert. Dabei wurden moderne Techniken eingesetzt, die ein umfassendes Verständnis der geologischen und geotechnischen Bedingungen des Gebiets ermöglichen. Ziel dieses Beitrags ist, Kenntnisse über die geologischen und geomechanischen Herausforderungen bei großen Tunnelbau‐Infrastrukturprojekten im Hochgebirge zu erweitern und konkrete Lehren daraus für ähnliche zukünftige Projekte zu ziehen.
Cross-scale rockmass characterization by high resolution seismic imaging around tunnels

Calin Cosma,Nicoleta Enescu

DOI: https://doi.org/10.1088/1755-1315/1124/1/012012

2023-01-11

IOP Conference Series: Earth and Environmental Science

Abstract:Reflection seismic surveys are relevant to the detailed characterisation of crystalline bedrock. Relatively small-scale features, even single fractures, can demonstrably be detected. Integrated analysis and modelling of geological, hydrogeological and geophysical data is instrumental in the interpretation of reflection seismic data. This requires the inference of the nature of the reflectors, e.g. lithological contacts or deformation zones and resolving the orientation ambiguity of the reflectors. Brittle deformation zones and large fractures may be heterogeneous in their detailed structure, making their characterization a challenging task. Several examples of structure characterization ahead and around tunnels are presented, with focus on the safety assessment for engineering and mining applications. Seismic imaging techniques adapted for tunnels and galleries are presented with examples from high resolution seismic surveys carried out at ONKALO (Finland) and Äspö HRL (Sweden). Studies performed over a span of several years demonstrate that large fractures identified initially through geological mapping, can also be found, positioned and characterized by seismics at the small scale of tunnels and/or boreholes. We show that reflection seismic surveys are relevant to the detailed characterization of crystalline bedrock. The detection of some distinctive features, even large-scale, can be uncertain if the survey layout is spatially constrained. Combinations of borehole and tunnel measurements using measuring arrays with diverse orientations helped reduce the location ambiguities and are recommended to be used in mining and tunneling rock characterization surveys wherever possible.
Analysis of TBM parameters during tunnelling in adverse conditions – The case study of the Frejus Safety Tunnel, Western Alps

Gianpino Walter Bianchi

DOI: https://doi.org/10.1002/geot.202200070

2023-02-01

Geomechanics and Tunnelling

Abstract:One of the main hazards during tunnel boring machine (TBM) excavation in hard rock is related to the occurrence of unforeseen adverse conditions, leading to unfavourable rock mass behaviour during tunnel boring. In this respect, the continuous analyses of TBM excavation parameters may represent an interesting tool for a continuous monitoring of geotechnical conditions at the tunnel face and for early detection of changing ground conditions in the rock mass. This work provides a back‐analysis of TBM data recorded during the excavation of the Frejus Safety Tunnel, bored across the French‐Italian border in the Western Alps. It is a 13 km‐long tunnel excavated by a 9.4 m diameter, single‐shield TBM through strongly anisotropic calcareous schist, with cover up to 1800 m. Main problems faced during TBM excavation were related to the local occurrence of buckling‐related convergence and consequent asymmetrical loading on the precast segment rings. Correlating TBM performance parameters to the encountered geological and geomechanical conditions provides the possibility to identify which parameters are most affected by geomechanical properties of the rock mass at the tunnel face and by rock mass behaviour. Conversely, the analysis indicates which parameters can be adopted as monitoring tool of ground conditions during TBM advance. In addition, this work highlights how buckling phenomena can be distinguished, in terms of TBM operation and performance, from other adverse conditions as, e.g., blocky ground or squeezing.
Breaking new ground: Decoding the root’s molecular circuits to penetrate compacted soil

Elohim Bello-Bello,Luis Herrera-Estrella

DOI: https://doi.org/10.1016/j.devcel.2024.01.028

IF: 13.417

2024-02-01

Developmental Cell

Abstract:Penetration capacity is a central root phenotype for enhancing rooting into compacted soils and improving abiotic stress tolerance in crop plants, but the molecular mechanisms are unclear. In this issue of Developmental Cell, Xu et al. demonstrate the vital role of the FER-PIF3-PIEZO circuitry in controlling primary root penetrability into compacted substrates.

cell biology,developmental biology
Mechanisms of Large Deformation in Soft Rock Tunnels: a Case Study of Huangjiazhai Tunnel

Kang Bian,Jian Liu,Zhenping Liu,Shangge Liu,Fei Ai,Xiaoqing Zheng,Shaohu Ni,Wei Zhang

DOI: https://doi.org/10.1007/s10064-017-1155-8

IF: 4.2

2017-01-01

Bulletin of Engineering Geology and the Environment

Abstract:Typical large-deformation phenomena of soft rock occurred frequently during the tunneling process in Huangjiazhai Tunnel, Hubei Province, China, including extrusion at the tunnel wall and severe damage of the primary support and secondary lining. To reveal the mechanisms of these anomalies, comprehensive investigations have been undertaken combining engineering, laboratory, and microscopic analyses. Since the monitoring results show that there might be a close relationship between the large deformation phenomena and water infiltration into the tunnel, the water–rock interaction is the research focus in the investigations. The experimental results reveal that the deforming resistance and strength of shales exposed at the excavation face weaken quickly in the first 20 days after the shales have contact with water. The results obtained by mineral composition detection and microstructure observation illustrate the microscopic reasons for the decreasing strength and deforming resistance of the tunnel surrounding rock after water infiltration. The results from in situ geostress tests indicate that as a result of high tectonic stress and low rock strength, the field of Huangjiazhai Tunnel is an extremely high geostress area. By combining analyses from the mechanical and geological perspectives, there are two main reasons for the large deformations in the Huangjiazhai Tunnel: the plastic flow caused by tunnel excavation under high geostress and low rock strength and a hydrated-mechanical coupling process between the shales and water.
Tunnel engineering enables multifaceted improvements in halogenase

Zhengyi Zhang,Huimin Zhao

DOI: https://doi.org/10.1016/j.checat.2022.09.010

2022-10-20

Chem Catalysis

Abstract:In a recent article in Nature Catalysis, Prakinee et al. applied a mechanism-guided protein-engineering strategy to optimize the behaviors of a flavin-dependent halogenase by tuning the hydrophobic interactions within the tunnel for hypohalous acid (HOX) transport. This strategy allows the control of the fate of enzymatic intermediates at low cost.
Deformation failure mechanism and characterization for black shale tunnels: A case study

Mateo Sanín Zuluaga,Silvana Montoya-Noguera

DOI: https://doi.org/10.1016/j.engfailanal.2024.108033

IF: 4

2024-02-03

Engineering Failure Analysis

Abstract:Excessive deformations in extensive excavations, especially in complex lithologies and tectonic settings, can lead to delays and increased costs. This paper presents a case study on the Guillermo Gaviria Echeverry (GGE) tunnel in the western Colombian mountain range, highlighting the importance of understanding rock characteristics and deformation causes. Focusing on the Penderisco formation, characterized by mudstones, lydites, and chert, with volcanic intrusions, the study investigates the deformations caused by water-induced weakening of clay minerals. Extensive research, including laboratory tests, field investigations, and analytical and numerical modeling, revealed significant deformations following the application of the final support. The study emphasizes the necessity of reevaluating geotechnical models to accurately represent real-world conditions, detailing the process of identifying and addressing the challenges in constructing what is set to be the longest road tunnel in Latin America. Countermeasures were proposed and evaluated through stress–strain analysis and geotechnical characterizations, showcasing a cost-effective technical solution for managing tunnel deformations.

engineering, mechanical,materials science, characterization & testing
Three-dimensional tunnel face extrusion and reinforcement effects of underground excavations in deep rock masses

Wuqiang Cai,Hehua Zhu,Wenhao Liang

DOI: https://doi.org/10.1016/j.ijrmms.2021.104999

IF: 6.849

2022-02-01

International Journal of Rock Mechanics and Mining Sciences

Abstract:The design experience and the shallow tunnel theory, which emphasize the plane strain assumption, two-dimensional (2D) strength theory, and indoor or back analysis-based parameters of rock mass, should not be directly adopted for deep tunnel design. This paper reports the development of a digital acquisition technique to quickly, automatically, and accurately obtain the in-situ strength parameters (e.g., GSI and D), followed by the establishment of a three-dimensional (3D) numerical model for deep tunneling for a typical tunnel in western China to study the 3D and nonlinear spatial effects and mechanisms during excavation with incorporation of the 3D Hoek-Brown (HB) strength criterion. The reliability and correctness of the developed methods were verified by the field monitoring data, and the results of our study showed that: (1) The deformations based on 2D strength criteria (e.g., HB and MC) and 3D criterion (e.g. GZZ) are close for shallow tunnel, but significantly different for deep tunnel because of the widely distributed plastic zone in deep tunneling, thereby indicating the obvious effect of intermediate principal stress (σ 2) on rock deformation; (2) The face extrusion deformation exhibits obvious nonlinear trends with an increasing buried depth, and the σ 3 of the core rock reflects a tensile value in deep tunnel, thereby indicating the presence of an extremely unstable state. Reinforcement could increase the overall stress inside the core rock and reduce the stress unloading effect caused by the strong disturbances of deep excavations, thereby promoting a gradual change from tensile stress to compressive stress; (3) A uniform relationship was found between pre-extrusion and pre-convergence deformations, indicating that the pre-convergence deformation of the surrounding rock could be controlled by constraining the pre-extrusion deformation of the core rock. This digital technique and such 3D HB-based (e.g., GZZ) numerical modeling may be promising for conducting the 3D forward and dynamic analyses of tunnel stability. Additionally, the core rock extrusion control can be treated as an active method to render the rock itself a natural support material and to realize its strength potential, thereby making a valuable contribution to the construction of deep and ultra-deep rock tunnels.

engineering, geological,mining & mineral processing

Tashni's first tunnel

Boring Technology and Practice for Small Section Tunnel under Complicated Geological Conditions

Development of surface settlement of twin tunnels under the influence of the river

Statistical Approach to Tunneling Time in Attosecond Experiments

Exis memoria

Geotechnical insights of mammal burrows in loose desert sand

Geomorphological and sedimentary features of an underwater lava tube: the Túnel de la Atlántida (Lanzarote, Spain)

Reinforcing Tunnel Network Exploration in Proteins Using Gaussian Accelerated Molecular Dynamics

Tunneling Nanotubes in the Brain

3D Simulation of TBM Excavation in Brittle Rock Associated with Fault Zones: the Brenner Exploratory Tunnel Case

Ant nest geometry, stability, and excavation–inspiration for tunneling

Mechanical behaviors of surrounding rock and supporting structure of shallow-buried unsymmetrical pressure tunnel crossing soil–rock interface

Las Leñas International Tunnel – Geomechanical challenges in large‐scale tunneling projects across The Andes

Cross-scale rockmass characterization by high resolution seismic imaging around tunnels

Analysis of TBM parameters during tunnelling in adverse conditions – The case study of the Frejus Safety Tunnel, Western Alps

Breaking new ground: Decoding the root’s molecular circuits to penetrate compacted soil

Mechanisms of Large Deformation in Soft Rock Tunnels: a Case Study of Huangjiazhai Tunnel

Tunnel engineering enables multifaceted improvements in halogenase

Deformation failure mechanism and characterization for black shale tunnels: A case study

Three-dimensional tunnel face extrusion and reinforcement effects of underground excavations in deep rock masses