Abstract:Amorphous thermoplastic polymers are important engineering materials; however, their non-linear, strongly temperature- and rate-dependent elastic-viscoplastic behavior is still not very well understood, and is modeled by existing constitutive theories with varying degrees of success. There is no generally agreed upon theory to model the large-deformation, thermo-mechanically-coupled, elastic-viscoplastic response of these materials in a temperature range which spans their glass transition temperature. Such a theory is crucial for the development of a numerical capability for the simulation and design of important polymer processing operations, and also for predicting the relationship between processing methods and the subsequent mechanical properties of polymeric products. In this paper we extend our recently published theory [Anand, L., Ames, N. M., Srivastava, V., Chester, S. A., 2009. A thermo-mechanically-coupled theory for large deformations of amorphous polymers. Part I: formulation. International Journal Plasticity 25, 1474–1494; Ames, N. M., Srivastava, V., Chester, S. A., Anand, L., 2009. A thermo-mechanically coupled theory for large deformations of amorphous polymers. Part II: applications. International Journal of Plasticity 25, 1495–1539] to fill this need.We have conducted large strain compression experiments on three representative amorphous polymeric materials – a cyclo-olefin polymer (Zeonex-690R), polycarbonate (PC), and poly(methyl methacrylate) (PMMA) – in a temperature range from room temperature to approximately 50°C above the glass transition temperature, ϑg, of each material, in a strain-rate range of ≈10-4 to 10-1s-1, and compressive true strains exceeding 100%. We have specialized our constitutive theory to capture the major features of the thermo-mechanical response of the three materials studied experimentally.We have numerically implemented our thermo-mechanically-coupled constitutive theory by writing a user material subroutine for a widely used finite element program. In order to validate the predictive capabilities of our theory and its numerical implementation, we have performed the following validation experiments: (i) a plane-strain forging of PC at a temperature below ϑg, and another at a temperature above ϑg; (ii) blow-forming of thin-walled semi-spherical shapes of PC above ϑg; and (iii) microscale hot-embossing of channels in Zeonex and PMMA above ϑg. By comparing the results from this suite of validation experiments of some key features, such as the experimentally-measured deformed shapes and the load-displacement curves, against corresponding results from numerical simulations, we show that our theory is capable of reasonably accurately reproducing the experimental results obtained in the validation experiments.

A generic formulation of anisotropic thermo-elastoviscoplasticity at finite deformations for finite element codes

An Approach to Elastoplasticity at Large Deformations

An Explicit Integration Algorithm for Introducing User-Defined Thermo-Viscoplastic Constitutive Models in Fe Simulations

A Multi-Phase Model for Transformation Plasticity Using Thermodynamics-Based Metallurgical Algorithm

A Thermomechanically Coupled Finite Deformation Constitutive Model for Shape Memory Alloys Based on Hencky Strain

A generalized anisotropic deformation formulation for geomaterials

A Co-Rotational Based Anisotropic Elasto-Plastic Model for Geometrically Non-Linear Analysis of Fibre Reinforced Polymer Composites: Formulation and Finite Element Implementation

A large deformation theory for rate-dependent elastic–plastic materials with combined isotropic and kinematic hardening

Elasto-plasticity theory for large plastic deformation and its use for the material stiffness determination

A multiplicative finite strain crystal plasticity formulation based on additive elastic corrector rates: Theory and numerical implementation

Fully anisotropic finite strain viscoelasticity based on a reverse multiplicative decomposition and logarithmic strains

A Finite Deformation Formulation for Amorphous Glassy Polymers under Moderate and Impact Strain Rates: Application to Adhesive Films

Development of a Constitutive Model to Predict the Elasto-Plastic Behaviour of 3D-Printed Thermoplastics: A Meshless Formulation

3-D Thermal-Elastic-Plastic Fem in Finite Deformation and Its Application to Non-Isothermal Sheet Forming

An Explicit Approach Toward Modeling Thermo-Coupled Deformation Behaviors of SMPs

A thermo-mechanically-coupled large-deformation theory for amorphous polymers in a temperature range which spans their glass transition

On the use of constrained reactive mixtures of solids to model finite deformation isothermal elastoplasticity and elastoplastic damage mechanics

Numerical framework for anisotropic flexible piezoelectrics with large deformation

A Generalized, Computationally Versatile Plasticity Model Framework - Part I: Theory and Verification Focusing on Tension‒compression Asymmetry

An additive Mori-Tanaka scheme for elastic-viscoplastic composites based on a modified tangent linearization

An objective isogeometric mixed finite element formulation for nonlinear elastodynamic beams with incompatible warping strains