Abstract:The increasing demand for high-performance aircraft engines has led to a greater emphasis being placed on advanced sealing coating technologies. Developing long-life, self-lubricating, and wear-resistant coatings is of significant research value. This study focuses on the fabrication of a novel self-lubricating and wear-resistant NiCoCrAlY-Cr2O3-AgMo composite coating. This coating was deposited onto a GH4169 substrate utilizing plasma spraying. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffraction (XRD) methods were employed to characterize the elemental composition and microstructure of the fabricated NiCoCrAlY-Cr2O3-AgMo composite coating. Microhardness measurements across the coating cross-section indicated a gradual increase in hardness from the GH4169 substrate to the NiCoCrAlY-Cr2O3-AgMo coating. The average hardness of the GH4169 substrate was 413.92 HV0.2, while the CoNiCrAlY bonding layer region exhibited an average hardness of 467.60 HV0.2. The NiCoCrAlY-Cr2O3-AgMo coating itself demonstrated an average microhardness of 643.22 HV0.2. Room temperature friction tests indicated that the average coefficient of friction (COF) of the GH4169 substrate was 0.665. In contrast, the NiCoCrAlY-Cr2O3-AgMo coating exhibited a significantly lower average COF of 0.16, representing a 75.94% reduction compared to the uncoated GH4169 substrate. High-temperature friction tests were conducted at 400 °C, 500 °C, and 600 °C, indicating average COF values of 0.438, 0.410, and 0.268, respectively, for the NiCoCrAlY-Cr2O3-AgMo coating. Specifically, at 600 °C, the formation of a lubricious NiMoO4 tribofilm on the coating surface was observed. This tribofilm effectively reduced the wear rate of the GH605 pin to 2.78 × 10−6 mm3/N·m, highlighting the potential of the NiCoCrAlY-Cr2O3-AgMo coating to reduce wear in high-temperature sliding contact applications.

Study on pin temperature and wear behaviour of plasma sprayed Ni-Cr coatings with nano Al2O3 particle

Study on high-temperature erosive wear behaviour, surface roughness and scratch resistance of NiCrAlY-based composite coating

Analysis of tribological behavior, pin temperature, and surface roughness of a brake pad material with nano coating

A Comparative Study of Erosion Wear Performance of Thermally Sprayed Ni-Based Composite Coatings

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

High-Temperature Wear Behavior and Mechanisms of Self-Healing NiCrAlY-Cr3C2-Ti2SnC Coating Prepared by Atmospheric Plasma Spraying

Abrasive wear behavior of nano-ceria modified NiCoCrAlY coatings deposited by the high-velocity oxy-fuel process

Microstructure and tribological behavior of plasma spray Ni60 alloy coating deposited on ZL109 aluminum alloy substrate

Tribological performance and high temperature oxidation behaviour of thermal sprayed Ni- and NiCrAlY-based composite coatings

Evaluation of wear resistance of CrN, CrAlN, and TiAlN coatings deposited by multi-arc ion plating on spinning die of Cr12MoV

A Study of Parameters Affecting Wear Resistance of Alumina and Yttria Stabilized Zirconia Composite Coatings on Al-6061 Substrate

Characterization of sputter-deposited hydrophobic chromium doped nickel alumnide coatings for mechanical and high-temperature oxidation-resistant applications

Sliding Wear Behavior of the Nanoceria-Doped AlCrFeCoNi High-Entropy Alloy Coatings Deposited by Air Plasma Spraying Technique

Comparative investigation and characterization of the nano-mechanical and tribological behavior of RF magnetron sputtered TiN, CrN, and TiB2 coating on Ti6Al4V alloy

Wear Properties of NiAl Based Materials

Wear resistance of Ni/nano-Al2O3 composite coatings by brush electroplating

Effect of Nickel Aluminide Microcrystalline Coating on High-Temperature Oxidation Behavior of NiAl-33.5%Cr-0.5%Zr Alloy

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

Tribological Properties of Craln and Tin Coatings Tested in Nano- and Micro-Scale Laboratory Wear Tests

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

Abrasive wear characteristics of plasma sprayed nanostructured alumina/titania coatings