The dynamic system of the traffic assignment problem: Part III. Incorporating traffic dynamics

Wen-Long Jin

DOI: https://doi.org/10.48550/arXiv.math/0503285

2007-11-17

Abstract:The paper has been merged into <a class="link-https" data-arxiv-id="math/0503283" href="https://arxiv.org/abs/math/0503283">math/0503283</a>

Dynamical Systems

What problem does this paper attempt to address?

Aging-dependent Strain Localization in Amorphous Glassy Polymers: from Necking to Shear Banding

Run Zhang,Pengxiang Bai,Dong Lei,Rui Xiao

DOI: https://doi.org/10.1016/j.ijsolstr.2018.03.030

IF: 3.667

2018-01-01

International Journal of Solids and Structures

Abstract:This study investigates the influence of physical aging on the tensile deformation behaviors of poly(ethylene terephthalate)-glycol. The polymers are subjected to a quenched and an annealed heat treatment, followed by deformation in tension. The digital image correlation (DIC) is used to capture the surface strain. The DIC results show that the deformation localization occurs in the post-yield strain softening region. The quenched and annealed polymers exhibit different localization types, representing as necking for quenched polymers and shear banding for annealed polymers. With the help of the DIC, the nucleation and propagation of the localization zones are fully captured. The DIC results show that the reference location with the maximum strain does not change with the deformation. At the same strain level, the maximum strain in the shear bands is much larger than that in the necks, which explains the failure strain of the annealed polymers is smaller than the quenched polymers. The stretch rate also has a strong effect on the localization behaviors. A larger stretch rate results in a stronger localization due to an increase in the amount of strain softening.
Analysis of Strain Localization in Porous Media with Transversely Isotropic Elasticity under Undrained Conditions

Y. Q. Zhang,L. Z. Wang,M. Pang,L. F. Fan

DOI: https://doi.org/10.15632/jtam-pl.55.1.199

2017-01-01

Abstract:The properties of strain localization for elastic-plastic porous media with transversely isotropic elasticity under undrained conditions are investigated. Under non-associated plasticity and tri-axial stress states, the conditions for strain localization of elastic-plastic porous media are derived, in which the effects of deviation from isotropic elasticity and pore fluid compressibility are included. Based on the Mohr-Coulomb yield criterion, the influences of the deviation from isotropic elasticity and pore fluid compressibility on the direction angle of localized band initiation and the corresponding critical hardening modulus for the case of plane strain are discussed. As a result, the properties of strain localization are dependent upon the deviation from isotropic elasticity and pore fluid compressibility. The deviation from isotropic elasticity and pore fluid compressibility has significant impacts on the direction angle of localized band initiation and the corresponding critical hardening modulus.
Shear Localization-Induced Amorphization in Nanocrystals During High Strain Rate Deformation

Qi-lin Xiong,Takahiro Shimada,Takayuki Kitamura

DOI: https://doi.org/10.1016/j.ijmecsci.2024.109324

IF: 7.3

2024-01-01

International Journal of Mechanical Sciences

Abstract:Shear localization is the predominant form of failure of metals at high strain rates where amorphization often occurs. However, the mechanism and role of amorphization in shear localization are not yet clearly understood. In this work, a series of shear deformations of nanocrystals with different grain sizes at high strain rates are investigated using molecular dynamics simulations. The results show that amorphization is not the result of thermal melting, but a new plastic deformation mechanism in the process of shear localization, which serves as a complement to dislocation and grain boundary to support plastic deformation at a high strain rate. The critical shear strain at which shear localization and amorphization occur is greater for small-grained specimens than for large-grained specimens. This can be attributed to the fact that small-grained specimens have more defects and slip systems that can be activated, which cause amorphization to occur later. The strain rate has a significant influence on shear localization and amorphization. The processes of shear localization and amorphization become more complicated at extremely high strain rates than at relatively low strain rates.
Structural transformation and localization during simulated nanoindentation of a non-crystalline metal film

Yunfeng Shi,Michael L. Falk

DOI: https://doi.org/10.48550/arXiv.cond-mat/0503286

2005-03-11

Materials Science

Abstract:A simulation study demonstrates that localization can arise as the result of the breakdown of stable quasi-crystal-like atomic configurations. Samples produced at elevated quench rates and via more energetic processes contain a lower fraction of such configurations and exhibit significantly less pronounced localization and shorter spacing between bands. In the samples produced by the lowest quench rates localization is accompanied by the amorphization of material with initially quasi-crystal-like medium range order. This result is of particular significance in light of recent experimental evidence of local quasi-crystal order in the most stable of the bulk metallic glasses.
Strain localization in a nanocrystalline metal: Atomic mechanisms and the effect of testing conditions

Timothy J. Rupert

DOI: https://doi.org/10.48550/arXiv.1407.5927

2014-07-23

Abstract:Molecular dynamics simulations are used to investigate strain localization in a model nanocrystalline metal. The atomic mechanisms of such catastrophic failure are first studied for two grain sizes of interest. Detailed analysis shows that the formation of a strain path across the sample width is crucial, and can be achieved entirely through grain boundary deformation or through a combination of grain boundary sliding and grain boundary dislocation emission. Pronounced mechanically-induced grain growth is also found within the strain localization region. The effects of testing conditions on strain localization are also highlighted, to understand the conditions that promote shear banding and compare these observations to metallic glass behavior. We observed that, while strain localization occurs at low temperatures and slow strain rates, a shift to more uniform plastic flow is observed when either strain rate or temperature is increased. We also explore how external sample dimensions influence strain localization, but find no size effect for the grain sizes and samples sizes studied here.

Materials Science,Mesoscale and Nanoscale Physics
ORIGIN OF HEAT EFFECTS AND SHEAR MODULUS CHANGES OF A Cu-BASED AMORPHOUS ALLOY

Zhang Langting,Vitaly Akhonik,Qiao Jichao

DOI: https://doi.org/10.6052/0459-1879-20-233

2020-01-01

Abstract:Shear modulus is one of important parameters to control the viscous flow, diffusion and structural relaxation of amorphous alloy. Macroscopic shear elasticity determines the change of heat flow. The correlation between the mechanical properties and the heat flow during the structural relaxation and glass transition is one of the important issues to understand the origin of mechanical properties of amorphous alloy. In the framework of the interstitialcy theory, the shear modulus, heat flow and viscosity of Cu$_{49}$Hf$_{42}$Al$_{9}$ amorphous alloy were used to probe the correlation between shear modulus and heat flow. In parallel, evolution of interstitialcy defects concentration was determined by shear modulus in initial and relaxed states. From the perspective of energy, the influence of interstitialcy defects concentration on the thermodynamic properties of amorphous alloy was investigated by activation energy spectrum (AES). Dynamic mechanical analysis (DMA) was used to investigate the dynamic mechanical process of the Cu$_{49}$Hf$_{42}$Al$_{9 }$ amorphous alloy. Structural relaxation induced by physical aging and the evolution of internal friction in-situ annealing was discussed. The results demonstrated that interstitialcy theory could accurately describe the relaxation kinetics, shear softening and other phenomena induced by structural relaxation of amorphous alloy. Temperature dependence of the shear modulus in initial and relaxed states can be well predicted by the data of differential scanning calorimetry (DSC). Activation energy spectrum directly reflects the interstitialcy defects concentration, which can be activated per unit activation energy. Structural relaxation leads to a reduction of the defect concentration, which indicates the structure transforms to a more stable state. During the glass transition process, defect concentration rapidly increases, which corresponds to the shear softening accompanied by heat absorption. Structural relaxation induces decrease of both internal friction and atomic mobility of amorphous alloy. However, the atomic mobility is high enough to eliminate the influence of structural relaxation on defect concentration in the supercooled liquid region.
Nucleation Mechanisms of Shear Bands in Amorphous Alumina

Qinqin Xu,Meng Liang,Guojian Lyu,Jichao Qiao,Chong Wei,Wenyi Huo,Stefanos Papanikolaou,Claudio Fusco

DOI: https://doi.org/10.1016/j.matchemphys.2024.129783

IF: 4.778

2024-01-01

Materials Chemistry and Physics

Abstract:The origin of the plastic deformation in amorphous solids is a challenging issue unlike that of the plasticity in crystals. Plasticity in amorphous systems can occur by the nucleation and propagation of shear bands (SBs). In this work, we investigate the mechanical response of an amorphous alumina sample subjected to shear deformation via extensive molecular dynamics simulations. We find SBs form only within a certain range of parameter values, e.g., low quenching rates, low temperatures and high strain rates. In our proposed atomic-scale model shear transformation zones (STZs) first nucleate and act as precursors of SBs due to their high stress concentration. The results showed that STZs generate an anti-symmetric stress that is responsible for the vortex-like motion of atoms that facilitate the percolation of STZs, finally forming an SB. These results provide insight into the mechanisms of plastic deformation of similar amorphous solids.
Localized crystallization in shear bands of a metallic glass

Zhijie Yan,Kaikai Song,Yong Hu,Fuping Dai,Zhibing Chu,Jürgen Eckert

DOI: https://doi.org/10.1038/srep19358

IF: 4.6

2016-01-01

Scientific Reports

Abstract:Stress-induced viscous flow is the characteristic of atomic movements during plastic deformation of metallic glasses in the absence of substantial temperature increase, which suggests that stress state plays an important role in mechanically induced crystallization in a metallic glass. However, it is poorly understood. Here, we report on the stress-induced localized crystallization in individual shear bands of Zr 60 Al 15 Ni 25 metallic glass subjected to cold rolling. We find that crystallization in individual shear bands preferentially occurs in the regions neighboring the amorphous matrix, where the materials are subjected to compressive stresses demonstrated by our finite element simulations. Our results provide direct evidence that the mechanically induced crystallization kinetics is closely related with the stress state. The crystallization kinetics under compressive and tensile stresses are interpreted within the frameworks of potential energy landscape and classical nucleation theory, which reduces the role of stress state in mechanically induced crystallization in a metallic glass.
Strain localization and failure of disordered particle rafts with tunable ductility during tensile deformation

Hongyi Xiao,Robert JS Ivancic,Douglas J Durian

DOI: https://doi.org/10.1039/D0SM00839G

2020-05-09

Abstract:Quasi-static tensile experiments were performed for a model disordered solid consisting of a two-dimensional raft of polydisperse floating granular particles with capillary attractions. The ductility is tuned by controlling the capillary interaction range, which varies with the particle size. During the tensile tests, after an initial period of elastic deformation, strain localization occurs and leads to the formation of a shear band at which the pillar later fails. In this process, small particles with long-ranged interactions can endure large plastic deformations without forming significant voids, while large particles with short-range interactions fail dramatically by fracturing at small deformation. Particle-level structure was measured, and the strain-localized region was found to have higher structural anisotropy than the bulk. Local interactions between anisotropic sites and particle rearrangements were the main mechanisms driving strain localization and the subsequent failure, and significant differences of such interactions exist between ductile and brittle behaviors.

Soft Condensed Matter
An atomistic study of deformation of amorphous metals

D. Srolovitz,V. Vitek,T. Egami

DOI: https://doi.org/10.1016/0001-6160(83)90110-4

1983-02-01

Acta Metallurgica

Abstract:The computer simulation of a shear deformation of a model monoatomic amorphous metal has been performed. The strain was applied incrementally, relaxing the structure at each step. The complete stress-strain curve was thus obtained. A large number of microscopic deformation events have been observed and analyzed using the description of the local atomic structure by the atomic level stresses. Although no temperature effects have been included in the present study the calculated stress-strain curve is in very good agreement with the stress-strain curves measured experimentally at or above room temperature. The common feature of these experiments and present calculations is, however, the homogeneity of the deformation. Hence, it is argued that fundamental microscopic deformation mechanisms are the same at low and high temperatures and the macroscopic differences arise owing to the strain localization in the former case. The regions of inhomogeneous atomic movement which results in plastic deformation, have not been found to be correlated with local density fluctuations in contrast with assumptions of the models based on free volume theory. They are, however, correlated with regions of high shear stresses, called τ-defects. These defects are formed during the deformation, are sustained by the applied stress and appear to act as stress concentrators in the vicinity of which a localized viscous flow develops.
Shear localization in polycrystalline metal at high-strain rates with dynamic recrystallization: Crystal plasticity modeling and texture effect

Wen An,Chuan-zhi Liu,Qi-lin Xiong,Zhenhuan Li,Xicheng Huang,Tao Suo

DOI: https://doi.org/10.1016/j.ijplas.2023.103616

IF: 8.5

2023-04-23

International Journal of Plasticity

Abstract:Shear localization is an important failure mode, or even the dominant mode in metals at high-strain rates. However, it is a great challenge to accurately predict the occurrence and evolution of shear localization in metals at the high-strain rate deformation. Here, a dislocation-based crystal plasticity constitutive model with a crucial mechanism of shear instability, namely dynamic recrystallization, was developed. The evolution equations of dislocation density and grain size in the process of dynamic recrystallization were proposed and incorporated into the new constitutive model. The threshold of the stored energy in crystals was used as the criterion for the occurrence of dynamic recrystallization. Dynamic compression of a nanograin Cu-Al alloy was performed using the crystal plasticity finite element method based on the new constitutive model, and good agreement of the numerical prediction with the existing experimental data validates the new constitutive model. The results show dynamic recrystallization can be a more dominant mechanism for the occurrence of shear instability than thermal softening. In addition, dynamic tension and shear of the Cu-Al alloys with five typical textures were also simulated, showing that both loading mode and texture can significantly affect the formation of shear localization. This work is helpful for us to understand the role of microstructural evolution in the formation of shear localization at high-strain rates and to design the microstructure for artificially controlling or preventing the formation of shear localization.

materials science, multidisciplinary,engineering, mechanical,mechanics
Theoretical and Experimental Study of Strain Localization Phenomenon Based on Phase Transition Theory

Fayuan Yan,Enzhi Wang,Xiaoli Liu,Chengzhi Qi,Yangyang Guo,Weiqiang Xie

DOI: https://doi.org/10.1063/5.0207063

IF: 4.6

2024-01-01

Physics of Fluids

Abstract:In the study of large-scale localized strain features, localized strain can lead to energy release and seismic effects. From the macroscopic process of localized strain, it is found that localized deformation is accompanied by structural weakening, which is due to phase changes in rocks. The phase change corresponds to the secondary phase transition process in physics. The present study illustrates this phenomenon from the perspective of secondary phase transition theory in statistical physics, combining the localized strain features on a large scale. Theoretical analysis and experimental studies were carried out using three brittle rocks, including marble, granite and red sandstone. First, two perturbation methods, i.e., Krylov-Bogoliubov method and Poincare method, are used to calculate the higher-order control equations in analytical model. The influences of control equation coefficients on the strain localization process are analyzed. Then the uniaxial compression tests are carried out on the three rocks to record the strain process. Finally, the theoretical and experimental results are compared to analyze the strain localization phenomenon. The comparison results show that both the Krylov-Bogoliubov solution and the Poincare solution in the analytical model can well describe the evolution characteristics of localized strain. It indicates that the theoretical model is valid and has high accuracy. The Poincare method better simulates the nonlinear phenomenon of strain localization. The present study provides a new theoretical method to better understand the strain localization phenomenon.
Non-localized deformation in metallic alloys with amorphous structure

H. F. Zhou,C. Zhong,Q. P. Cao,S. X. Qu,X. D. Wang,W. Yang,Jianzhong Jiang

DOI: https://doi.org/10.1016/j.actamat.2014.01.003

IF: 9.4

2014-01-01

Acta Materialia

Abstract:In bulk or ribbon metallic alloys with monolithic amorphous structure, plastic deformation at room temperature is dominated by highly localized shear banding. Here we report suppressed shear localization under tension in a metallic glass (MG) embedded with pre-existing amorphous shear bands using large-scale atomistic simulations. It is demonstrated that pre-deformation lowers material strength and triggers enhanced strain fluctuation before sample yielding, leading to highly dispersed plastic shearing in the entire sample. Furthermore, the transition in deformation mode from highly localized shear banding to non-localized plastic deformation is associated with the competition between the yield strength of the material and the critical stress required for the formation of mature shear bands in the load-bearing materials. Given that a sufficient amount of glassy heterogeneities can be introduced into MGs under experimental conditions, the obtained results could provide a promising strategy for designing tensile ductile MGs with pure amorphous structure at room temperature.
Shear localization in metallic materials at high strain rates

Na Yan,Zezhou Li,Yongbo Xu,Marc A. Meyers

DOI: https://doi.org/10.1016/j.pmatsci.2020.100755

IF: 48.165

2021-06-01

Progress in Materials Science

Abstract:Three factors govern adiabatic shear localization: strain hardening (or softening), strain-rate hardening, and thermal softening. It is typically associated with large shear strains (>1), high strain rates (103-107 s-1), and high temperatures (40-100% of melting point), all of which happen within narrow regions with widths of about 1-200 μm.It is often an undesirable phenomenon, leading to failure, but there are situations where it is desirable, e. g., the generation of machining chips. Here, we review the development of both theoretical and experimental achievements, from the initiation of shear bands to their propagation with emphasis on three aspects: novel experimental techniques, novel materials, and nano/microstructural effects. The principal characteristics of adiabatic shear bands in metallic materials at the nano- and micro-scale are described. Bands that were formerly identified as transformed actually consist of nanocrystalline/ultrafine grains. These grains result from the breakup of the microstructure by a rotational recrystallization process.The evolution of the microstructure inside shear bands and their interactions for hcp, bcc, and fcc alloys, high-entropy alloys, nanocrystalline alloys, and metallic glasses are analyzed mechanistically.The gaps in the field and opportunities for future research are identified. Modern experimental characterization and computational techniques enable a more profound and predictive understanding of adiabatic localization and its avoidance in advanced materials.

materials science, multidisciplinary
A Local Statistical Structural Model for Amorphous Solids

sun qiang

DOI: https://doi.org/10.1088/0256-307X/30/12/126102

2013-01-01

Chinese Physics Letters

Abstract:From Raman spectroscopic study on OH stretching bands, the local statistical interpretation for water structure is proposed. Due to the closely structural relationship between amorphous solids and liquids, the structural model is extended to investigate the amorphous solids, which indicates that various intensity of potential can be expected around an atom (molecule). From this, a local statistical order parameter is proposed to understand the short-range order and long-range disorder. The order parameter is influenced by the cooling rate in the glass formation, which means that glass is formed with a slower cooling rate, and has higher structural order. For amorphous solids, the geometric topology is closely related to chemical bonding type, such as covalent bond and metallic bond.
Scaling of relaxation and excess entropy in plastically deformed amorphous solids

K.L. Galloway,Xiaoguang Ma,Nathan C. Keim,Douglas J. Jerolmack,Arjun G. Yodh,Paulo E. Arratia

DOI: https://doi.org/10.1073/pnas.2000698117

2021-08-06

Abstract:When stressed sufficiently, solid materials yield and deform plastically via reorganization of microscopic constituents. Indeed, it is possible to alter the micro-structure of materials by judicious application of stress, an empirical pro- cess utilized in practice to enhance the mechanical properties of metals. Un- derstanding the interdependence of plastic flow and microscopic structure in these non-equilibrium states, however, remains a major challenge. Here, we ex- perimentally investigate this relationship, between the relaxation dynamics and microscopic structure of disordered colloidal solids during plastic deformation. We apply oscillatory shear to solid colloidal monolayers and study their particle trajectories as a function of shear rate in the plastic regime. Under these cir- cumstances, the strain rate, the relaxation rate associated with plastic flow, and the sample microscopic structure oscillate together but with different phases. Interestingly, the experiments reveal that the relaxation rate associated with plastic flow at time t is correlated with the strain rate and sample microscopic structure measured at earlier and later times, respectively. The relaxation rate, in this non-stationary condition, exhibits power-law shear-thinning behavior and scales exponentially with sample excess entropy. Thus, measurement of sample static structure (excess entropy) provides insight about both strain-rate and constituent rearrangement dynamics in the sample at earlier times.

Soft Condensed Matter
Characterization of Mechanical Heterogeneity in Amorphous Solids

H. L. Peng,M. Z. Li,B. A. Sun,W. H. Wang

DOI: https://doi.org/10.1063/1.4739260

IF: 2.877

2012-01-01

Journal of Applied Physics

Abstract:The structural geometry and size distribution of the local atomic rearrangements induced by external stress in amorphous solids are investigated by molecular dynamics studies. We find that the size distribution exhibits a generic power-law behavior and their structural geometry shows fractal feature. This indicates that the local atomic rearrangements in amorphous solids are self-organized during deformation. A simple theoretical model based on the interaction of the heterogeneous elastic field sources is proposed which predicts the power-law scaling and characterizes the properties of the local atomic rearrangements in amorphous solids.
Localization and Macroscopic Instability in Nanoporous Metals

Sun Zhangtao,Guo Tianfu,Elkhodary Khalil I.,Yang Hang,Zhou Nian,Tang Shan

DOI: https://doi.org/10.1007/s10409-022-21538-x

2022-01-01

Abstract:Ductile fracture generally relates to microscopic voiding and to strain localization in metallic materials. When the void size is reduced to the nanoscale, size effects often lead to a different macroscopic plastic behavior from that established for the same material with larger voids. For example, irradiation of metallic materials can generate a large number of voids at the nanoscale, leading to complex deformation behaviors. The present work advances the understanding of strain localization in nanoporous metallic materials, connecting both the microscopic (nano-) and macroscopic scales. To explore the physical mechanisms at the nanoscale, molecular dynamics (MD) simulations were here carried out, capturing multiple nanovoids explicitly. Then, a homogenized continuum theory based in Gurson’s constitutive framework is proposed, which enables us to explore how localized behavior at the macroscopic scale evolves. The homogenized model incorporates the surface tension associated with nanosized void. The importance of this surface tension is illustrated by several parametric studies on the conditions of localization, when a specimen is subjected to uniaxial tension. Our parametric studies show that for smaller nanovoid sizes, and for a hardening matrix material, shear localization onset is delayed. Our proposed homogenization model was then used to predict localization behavior captured by our MD simulation. The yield stress and the localization strain predicted by our continuum model are in general agreement with the trends obtained by MD simulation. Moreover, based on our present study, experimental results of shear failure strain vs. dose of irradiation for several metals could be qualitatively explained rather successfully. Our model can therefore help shed light on prolonging the operation limits and the lifetime of irradiated metallic materials under complex loading conditions.
Spatiotemporal analysis of nonaffine displacements in disordered solids sheared across the yielding point

Nikolai V. Priezjev

DOI: https://doi.org/10.1007/s11661-020-05774-5

2019-10-03

Abstract:The time evolution and spatial correlations of nonaffine displacements in deformed amorphous solids are investigated using molecular dynamics simulations. The three-dimensional model glass is represented via the binary mixture, which is slowly annealed well below the glass transition temperature and then sheared at a constant strain rate. It is shown that with increasing strain, the typical size of clusters of atoms with large nonaffine displacements increases, and these clusters remain spatially homogeneously distributed, until the yielding point when mobile atoms become localized within a system-spanning shear band. Furthermore, the yielding transition is associated with an abrupt change in the spatial correlation of nonaffine displacements, which varies from exponential to power-law decay. We also find that the height of the first peak in the pair correlation function of small atoms exhibits a distinct increase at the yielding strain. These results are discussed in relation to the yielding transition in amorphous materials under cyclic loading.

Soft Condensed Matter,Materials Science,Computational Physics
Coarse graining atomistic simulations of plastically deforming amorphous solids

Adam R Hinkle,Chris H Rycroft,Michael D Shields,Michael L Falk,Adam R. Hinkle,Chris H. Rycroft,Michael D. Shields,Michael L. Falk

DOI: https://doi.org/10.1103/physreve.95.053001

IF: 2.707

2017-05-05

Physical Review E

Abstract:The primary mode of failure in disordered solids results from the formation and persistence of highly localized regions of large plastic strains known as shear bands. Continuum-level field theories capable of predicting this mechanical response rely upon an accurate representation of the initial and evolving states of the amorphous structure. We perform molecular dynamics simulations of a metallic glass and propose a methodology for coarse graining discrete, atomistic quantities, such as the potential energies of the elemental constituents. A strain criterion is established and used to distinguish the coarse-grained degrees-of-freedom inside the emerging shear band from those of the surrounding material. A signal-to-noise ratio provides a means of evaluating the strength of the signal of the shear band as a function of the coarse graining. Finally, we investigate the effect of different coarse graining length scales by comparing a two-dimensional, numerical implementation of the effective-temperature description in the shear transformation zone (STZ) theory with direct molecular dynamics simulations. These comparisons indicate the coarse graining length scale has a lower bound, above which there is a high level of agreement between the atomistics and the STZ theory, and below which the concept of effective temperature breaks down.

physics, fluids & plasmas, mathematical

The dynamic system of the traffic assignment problem: Part III. Incorporating traffic dynamics

Aging-dependent Strain Localization in Amorphous Glassy Polymers: from Necking to Shear Banding

Analysis of Strain Localization in Porous Media with Transversely Isotropic Elasticity under Undrained Conditions

Shear Localization-Induced Amorphization in Nanocrystals During High Strain Rate Deformation

Structural transformation and localization during simulated nanoindentation of a non-crystalline metal film

Strain localization in a nanocrystalline metal: Atomic mechanisms and the effect of testing conditions

ORIGIN OF HEAT EFFECTS AND SHEAR MODULUS CHANGES OF A Cu-BASED AMORPHOUS ALLOY

Nucleation Mechanisms of Shear Bands in Amorphous Alumina

Localized crystallization in shear bands of a metallic glass

Strain localization and failure of disordered particle rafts with tunable ductility during tensile deformation

An atomistic study of deformation of amorphous metals

Shear localization in polycrystalline metal at high-strain rates with dynamic recrystallization: Crystal plasticity modeling and texture effect

Theoretical and Experimental Study of Strain Localization Phenomenon Based on Phase Transition Theory

Non-localized deformation in metallic alloys with amorphous structure

Shear localization in metallic materials at high strain rates

A Local Statistical Structural Model for Amorphous Solids

Scaling of relaxation and excess entropy in plastically deformed amorphous solids

Characterization of Mechanical Heterogeneity in Amorphous Solids

Localization and Macroscopic Instability in Nanoporous Metals

Spatiotemporal analysis of nonaffine displacements in disordered solids sheared across the yielding point

Coarse graining atomistic simulations of plastically deforming amorphous solids