Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Micro/Nano Na 3 V 2 (PO 4 ) 3 /N-Doped Carbon Composites with a Hierarchical Porous Structure for High-Rate Pouch-Type Sodium-Ion Full-Cell Performance

Micro/Nano Na3V2(PO4)3/N-Doped Carbon Composites with a Hierarchical Porous Structure for High-Rate Pouch-Type Sodium-Ion Full-Cell Performance

A Hierarchical N/S‐Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High‐Performance Sodium‐Ion Batteries

N-doped dual carbon-layer-modified Na3V2(PO4)3 as a high-performance cathode material for sodium-ion batteries

Na 3 V 2 (PO 4 ) 3 @nitrogen,sulfur-codoped 3D porous carbon enabling ultra-long cycle life sodium-ion batteries.

Boosting High-Rate Sodium Storage Performance of N-Doped Carbon-Encapsulated Na 3 V 2 (PO 4 ) 3 Nanoparticles Anchoring on Carbon Cloth.

Synergistically Boosting Sodium-Storage Performance of Na 3 V 2 (PO 4 ) 3 by Regulating Na Sites and Constructing 3D Interconnected Carbon Nanosheet Frameworks

Boosting High‐Rate Sodium Storage Performance of N‐Doped Carbon‐Encapsulated Na <sub>3</sub> V <sub>2</sub> (PO <sub>4</sub> ) <sub>3</sub> Nanoparticles Anchoring on Carbon Cloth

Nitrogen-Doped Carbon Coated Na 3 V 2 (PO 4 ) 2 F 3 Derived from Polyvinylpyrrolidone as a High-Performance Cathode for Sodium-Ion Batteries

3D interconnected porous carbon coated Na3V2(PO4)3/C composite cathode materials for sodium-ion batteries

Nanoconfined Carbon‐Coated Na3V2(PO4)3 Particles in Mesoporous Carbon Enabling Ultralong Cycle Life for Sodium‐Ion Batteries

Carbon-Coated Na3v2(Po4)(3) Anchored on Freestanding Graphite Foam for High-Performance Sodium-Ion Cathodes

Three-dimensional Na3V2(PO4)3@carbon/N-doped graphene aerogel: A versatile cathode and anode host material with high-rate and ultralong-life for sodium storage

N/S Co-Modified Carbon/Na3V2(PO4)3 with High Rate Capability in Zn-ion storage

N/P-dual-doped carbon coated Na3V2(PO4)2O2F microspheres as high-performance cathode material for sodium-ion batteries.

Sol–gel design strategy for embedded Na3V2(PO4)3 particles into carbon matrices for high-performance sodium-ion batteries

One–Step Synthesis of Three–Dimensional Na3V2(PO4)3/Carbon Frameworks as Promising Sodium–Ion Battery Cathode

Ostwald Ripening Tailoring Hierarchically Porous Na3 V2 (PO4 )2 O2 F Hollow Nanospheres for Superior High-Rate and Ultrastable Sodium Ion Storage.

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

Na3V2(PO4)3 Coated by N-doped Carbon from Ionic Liquid As Cathode Materials for High Rate and Long-Life Na-ion Batteries

In-situ structural evolution analysis of Zr-doped Na3V2(PO4)2F3 coated by N-doped carbon layer as high-performance cathode for sodium-ion batteries