Abstract:Tremendous amount of fossil fuel is consumed in the form of low-grade waste heat (< 130 °C) due to inefficient energy utilization, and harvesting this waste heat as useful electricity contributes to mitigating the increasing energy crisis and the global greenhouse effect. Recently, compared with the past technologies (e.g. solid-state thermoelectric generator (s-TEG) and organic Rankine cycle (ORC)), liquid-based thermo-electrochemical batteries or systems feature more efficient and low cost for heat-to-electricity conversion. Among them, bimetallic thermally regenerative ammonia batteries (B-TRABs) based on redox reactions and ammonia thermal distillation that output the highest power density. However, all the existing ammonia batteries exhibit a common phenomenon that their discharge voltage curve basically has no stable platform and gradually decreases after peaking early, which is mainly due to the large pH difference between catholyte and anolyte, leading to self-discharge and severe energy decay. Here, an electrolyte decoupled strategy is proposed for a Cu/Zn-TRAB to restrain the self-discharge and enhance energy density as well as power generation at high temperatures. The self-discharge by ions cross contamination is observed visually as a colour evolution of the interlayer solution, and a transition of principal cathodic reactant from Cu(NH3)4 2+ to Cu2+ exists during discharging, which signals the beginning of performance degradation. The results demonstrate that the decoupled Cu/Zn-TRABs with double and triple-membrane designs improve the energy density by 45-50%, mainly due to the delay of transition region. With an energy density of 1034 W h m-3 obtained by a decoupled Cu/Zn-TRAB with double-membrane design, a thermoelectric conversion efficiency of 1.86% (15.6% relative to the Carnot efficiency) is achieved at a condenser temperature of 16 °C.

3-D printed gradient porous composite electrodes improve anodic current distribution and performance in thermally regenerative flow battery for low-grade waste heat recovery

Performance of a thermally regenerative ammonia-based battery using gradient-porous copper foam electrodes

Biomass waste-derived hierarchical porous composite electrodes for high-performance thermally regenerative ammonia-based batteries

Construction of a hierarchical porous surface composite electrode by dynamic hydrogen bubble template electrodeposition for ultrahigh-performance thermally regenerative ammonia-based batteries

A Review of Porous Electrode Structural Parameters and Optimization for Redox Flow Batteries

Cu/Ni composite electrodes for increased anodic coulombic efficiency and electrode operation time in a thermally regenerative ammonia-based battery for converting low-grade waste heat into electricity

Performance of a non-aqueous nanofluid thermally regenerative flow battery for electrical energy recovery from low-grade waste heat

Numerical Study on Heat and Ion Transport Characteristics Enables Optimal Design of Aqueous Thermocells for Low-Grade Heat Recovery

Thermally Regenerative Flow Batteries with pH Neutral Electrolytes for Harvesting Low-Grade Heat

Ammonia crossover in thermally regenerative ammonia-based batteries for low-grade waste heat recovery

A fluidized-bed reactor for enhanced mass transfer and increased performance in thermally regenerative batteries for low-grade waste heat recovery

High Power Thermally Regenerative Ammonia-Copper Redox Flow Battery Enabled by a Zero Gap Cell Design, Low-Resistant Membranes, and Electrode Coatings

Effect of operating parameters on the performance of thermally regenerative ammonia-based battery for low-temperature waste heat recovery

Power generation enhancement of a membrane-free thermally regenerative battery induced by the density difference of electrolytes

Graphene oxide modified membrane for alleviated ammonia crossover and improved electricity generation in thermally regenerative batteries

Analysis and Optimization of Thermally-Regenerative Ammonia-Based Flow Battery Based on a 3-D Model

Alleviated ammonia crossover in thermally regenerative ammonia-based batteries by optimizing the introduced intermediate-chamber

The coupled removal of heavy metals from electroplating wastewater induced stable electricity generation during long-time discharging in a three-chamber thermally regenerative battery

A Bimetallic Thermally-Regenerative Ammonia-Based Flow Battery for Low-Grade Waste Heat Recovery

Enhancing Low-Grade Thermal Energy Recovery in A Thermally Regenerative Ammonia Battery Using Elevated Temperatures

An Electrolyte-Decoupled Ammonia Battery for Enhancing Electricity Production from Low-Grade Waste Heat